User's Manual

ManualsBrandsArdi Technology ManualsElectronicsWireless Electronic Tracker(2.4GHz)

Pick Buster User Manual

Packing description

This product contains:

* Key ring master x 1

* Battery CR2016 x 2 (inside of card slave)

* Card slave x 1

* Protection insert for card slave x 2

* Battery LR44 x 3 (inside of master)

The battery installment and the key description

(1) Master battery installment, as shown in the illustration.

(2) Slave battery installment, as shown in the illustration. (Two protection inserts attached for your future replacement)

(3) Key description for master and slave, as shown in the illustration.

Specifications

Master specification: Key ring type

Size : 63 x 42 x 17.3 (mm)

Frequency : 2.4GHz ISM

Battery

: 303/AG13/LR44 x 3pcs

Button (1)

: Power switch

Button (2)

: Range detect switch

Button (3)

: LED flashlight switch

LED : 5 LEDs status indictor (when activated)

LED Light

: 1 white LED flashlight

Slave specification: Slim card type

Size : 80 x 50 x 2.4 (mm)

Frequency : 2.4GHz ISM

Battery

: CR2016 x 2pcs

Button

: Power switch

LED : 1 LED status indictor (when activated)

LED indictor for detect

Power switch

1. Remove the screw in back of master battery cover,

and take out battery cover.

2. Make sure the battery's positive (

) and negative (

) ends

are facing correctly when load it into the unit as shown in

direction (total three batteries), and put battery cover back,

then screw tighten it.

1. Make sure the battery's positive (

) and

negative (

) ends are facing correctly

when load it into the unit as shown in

direction (total three batteries).

2.Stick the protection insert.

3. When replace new battery, please pull

U-type tab and remove protection insert

and the old battery, then follow the step

and for replacement.

1 2

Operating instructions

(1) In the first time use, Please take out the plastic piece for electronic isolation on the battery slot of master and slave. (one piece on master, two

pieces on slave)

(2) Turn to power "ON" position for master and slave devices at the same time (in around 3 seconds), after master makes "Beep" sound, and slave

device will start to flash LED light synchronal, then the device will be into the stand-by mode and ready to use.

(3) Please put the slave and the master separately, and not separate both of them too far. For example, the slave can be put in the wallet or handbag,

the master can be put in your pocket, or hang in the handbag strap, or attach to the leather belt. Because static electricity will be occurred by

human body, if any happen and cause master device beep sounds randomly, please try to

relocate the master position. (Please refer to Handling Precautions 2, and 3)

(4) If the wallet with card slave attached was stolen and left around 3 to 8m, the master will beep

high-frequency warming sounds (95dB/30cm approximately, battery is in full charged condition),

and into the warning mode. As shown in the illustration. (Please refer to Handling Precautions 2)

(5) To long press on "Distance" key of master device, if master flashes the range detect LED (with 5 lights), under 15 to 20m, 5 LEDs light may show

how far the distance between master and slave. (Please refer to light signal and beep sound description) (Please refer to Handling Precautions 3)

(6) In distance detect mode, if master flashes the range detect LED under 15~20m, the user may use master to survey 360° direction. If ranges detect

LED increase lights in somewhere, then slave device possibly are located the position. As shown in the illustration.

(7) In warming mode or distance detect mode, be ware that when slave device is over 30 to 50m from master device, the detect action will be failed

when over the limitation of detect distance. If slave device is back 30 to 50m, detect function will be able to search and return to alarm mode or

distance detect mode. (Please refer to Handling Precautions 3)

(8) To long press on "Light" key of master device, may enter the flashlight mode.

(9) If static electricity is occurred by human body or irregular work by any artificial influence, please turn off and turn on again (reset) for both master

and slave devices.

under 5~15m

under 30~50m

360°

Master Slave

* User Manual x 1

White LED

button

Flashlight with high

brightness white LED

LED indictor for detect and

available range(when activated)

Switch button for detect

Power switch

over 3~8m

Insert

PB-101 / 91M-0003-U50G00

The light signal and beep sound description

Master light signal and beep sound Slave light signal and

beep sound

Near

To long press on "Distance" key of master device, and show how far the

distance between master and slave by LED indictor and beep sounds

Distance detect

mode

+BeepBeepBeep

No battery power for operation (Slave)No battery power

mode (Slave)

+BeepBeepBeep

Any irregular work by artificial influence, devices folded or distortion,

please turn off and turn on (reset) for both master and slave devices

Others

Stand-by mode(1) Turn on both master and slave devices, they will start to flash

LED light synchronal

Turn on both master and slave devices, they will start to flash

LED light synchronal

Stand-by mode(2)

+Beep +Beep

Under 30 to 50m with signal appear, but searchable range is over

15 to 20m

+Middle frequency

Beep

+Beep

Under 30 to 50m with signal appear, and searchable range is

under 15 to 20m, and range is long

+Middle frequency

Beep

+Beep

Under 30 to 50m with signal appear, and searchable range is

under 15 to 20m, and range is close

+High frequency

Beep

+Beep

Under 30 to 50m with signal appear, and searchable range is

under 5 to 15m, and range is close with side

+High frequency

Beep

+Beep

Under 30 to 50m with signal appear, and searchable range is

under 3 to 10m, can hear the beep sounds of slave, carefully

+Beep~10seconds

~Beep

Battery power is lower than standard working power (Master)Low battery power

mode (Master)

+Beep~10seconds

~Beep

Battery power is lower than standard working power (Slave)Low battery power

mode (Slave)

+BeepBeepBeep

No battery power for operation (Master)No battery power

mode (Master)

+Alarm sound

Slave is over 3 to 8m between master, start to beep sounds by

alarm mode

Alarm mode

+Low frequency

Beep

+Beep

Under 30 to 50m with signal appear, and searchable range is

under 15 to 20m, but range is long

:The circle symbol indicates light shine :The semicircle symbol indicates light flash

In warming mode or distance detect mode, slave device is over

30 to 50m from master device and detect fail

No signal mode

+BeepBeepBeep +BeepBeepBeep

Far

Summary of content (2 pages)

PAGE 1
Operating instructions Pick Buster User Manual © 2008 All Right Reserved Packing description This product contains: * Key ring master x 1 * Card slave x 1 * Battery LR44 x 3 (inside of master) * Battery CR2016 x 2 (inside of card slave) * Protection insert for card slave x 2 * User Manual x 1 The battery installment and the key description 5 (1) Master battery installment, as shown in the illustration.
PAGE 2
Suggested Using Method Handling Precautions (A) (B) Figure A Master device can be attached to the leather belt, and slave device can be put in the wallet, then put in your pocket. Figure B Master device can be attached to the leather belt, and slave device can be put in the handbag or suitcase. (C) (D) (1) Except for battery replacement for slave device, please do not paste protection insert in other place. It may cause protection insert to lose stickiness, and bad connection with devices.