Mini Tracker 505 User Manual
Master Front Buzzer Right direction LED light button (Mute distance melody button at search mode) Mode switch Mute Signal indication Search button Power on (Standby) Power off (Sleeping) Hanging hole for strap LED light Slave Back Distance indication Left direction Clip Front Battery cover Back Hanging hole for strap Signal indication 1
Working Method Master Slave Slave 8~16m No Alarm Alarm Search 0m 100 m Specification Master Size Frequency Battery Switch Button Slave : 39x48x6.8mm : 2.4GHz ISM : LR1130 x 2pcs : 3 sections : 2 buttons Size : 19x28x7.5mm Frequency : 2.
The Battery Installment Master 2 1. Press the clip on battery cover then push backwardly. 2. Put 2pcs batteries into. ***Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on battery cover. 1 3. Set the battery cover back.
Slave 1. Open from the fillister on the bottom of housing or curve side by your nail, like open shell. 1 2. Put 2pcs batteries into. *** Make sure the installment direction of positive (+) & negative (-) of battery are followed up the drawing showed on the inside of back battery cover. 2 3 1 3. Set back the battery cover.
Getting Started 1. 2. For the first time use, please set the battery into Master according to above battery installment . Switch to power on 3. Plastic isolation 4.
5. 6. Beep Beep Distance indication Signal indication Re-link successful! Master shows the distance with Slave via LED and melody (beep). Signal LED ON for re-linking. Important Beep If Master can't link with Slave, it will beep once every few seconds.
[Suggested setting place] Master Slave 7
Alarm Beep Beep Signal indication Over 8~16 meter. Come with beep! Stop alarm (beep) if both devices comes within 8 meter again.
Search Beep Beep Distance indication Press Search button 2~3 seconds 4 Distance indication LED and Right/Left direction LED lights up 1 second then release the Search button. Start to detect the location of Slave Display the intensity of signal on Master by 1.) LED light: more closer, more lights. 2.) Search melody: more closer, more rapid.
[Suggestion: Go to original direction or make a turn.] 0~100 m Flash signal LED by 3 seconds 1.) When Slave is on the back side. 2.) Go to wrong direction When Slave in the front of left side. 0~ 10 0m Near 0~100 m Right direction indication 1~2 m When Slave in the front of m 00 right side.
Press Search button 2~3 seconds Stop searching Back to Standby mode Signal indication Signal LED flashes every second for re-linking Important a.) Wrong holding Correct holding 90 < 90 Keep Master parallel Keep Master inclined or vertical b.) Error indication - whole direction LED goes off but signal LED lights up 3 seconds then displays new searched distance. b-1.) Search from correct direction to wrong direction b-2.
Location: North North Signal indication LED East Go the wrong direction 0~100 meter Distance LED goes out all lights suddenly and only flash Signal LED with beep sound Original searching (Right direction) North East 3 seconds later [Suggestion] LED displays new searched distance 12 Go back to original search direction or location
c.) Mute searching melody from Master. Listen beep sound from Slave to assist short range searching.
Sleeping (No Need The Guard Service) a.
b.
Important Beep Can't get signal from Slave. Signal LED flashes each second & comes with beep. (Slave maybe out off working range 100 meter, or no power.) Mute (Mute At Search mode, Or No Need The Guard Service) a.
b.) Press Search button Only Display the distance indication LED without searching melody Important Under mute mode, the Alarm function is disabled. Low Battery 1 beep sound every 20 seconds continuously. Important If this kit is under low battery stage, it may cause abnormal display to alarm, beeps or non-working to confuse actual working stage. Please change new battery as soon as possible.
Care and maintenance (a) Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. (b) Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. (c) Do not store the device in hot areas.
Recycle: The Battery provided in this product should be recycled to protect the local environment. Please contact with local recycle department for detail. Warning: Do not put the battery into the fire or heat resource. It will be cause dangerous or even explosion. FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
91E-0213-U50G00