5634PEW User's Manual EE ee 1 i Congratulations on purchasing the most sophisticated modem available, our modem combines advanced technology with state-of-the-art features ] to bring you the modern advanced communications device available today! This modem provides the following features. ® Data Mode Capabilities ~ V.90 56kbps ~ IT-T V.34 33.6kbps and fallback V.32bis -. V.22bis ~ V22 ~V21 ~Bell 212A Bell 103 ~ Standard AT command set ~ and MNP error correction V.
S634PEW User's Manual Table Contents Table Contents... 2 Chapter 1 Installation. oso 3 1.1 Checking your components 1.2 What else you need... 3 1.3 Installing the modem... 3 1.4 Removing the computer cover... 4 1.5 Inserting the modem 1.7 Connecting to your telephone... 5 1.8 Verifying your connection 6 1.9 Modem Driver Installation ( PnP 8 Chapter 2 AT commands and Result Code Responses... 9 2.1 Starting an AT Command Session... Entering Commands ee 10 2.3 Using the Escape Command... 10 2.
S634PEW User's Manual ee ith Chapter 1 Installation Chapter 1 provides detailed instructions for installing your modem. 1.1 Checking your components Unpack your components and make sure you have the following items; The modem. A modular telephone cable to connect your modem to the telephone line. This user's manual. Communication software and manual. When you open your package, make sure all of the above items are included and not damaged.
S634PEW User's Manual different computer, refer to the manual that accompanied your computer or contact your computer dealer for instructions on installing the modem in your personal computer. 1.4 Removing the computer cover Turn off the personal computer's power. No power must be applied to your computer when you install the internal modem and computer could be damaged. . Make sure you can freely access the back of the personal computer. Unscrew the necessary screws to loosen the computer cover.
S5634PEW User's Manual modem in the PCI soot. You may want to test the modem's telephone connection (described in the next section) before securing your modem. 7. Use the cover-mounting screws to secure the computer cover, Figure 1-3. Inserting the modem 1.6 Connecting to the telephone line Use the following procedure to connect your made ta the telephone line: 1. Make sure you have an JR-11 telephone jack.
S634PEW Manual that lets you connect your telephone to the same telephone line the modem is using. This lets you manually dial data calls or make voice calls when you are not using your modem 1. Use the following procedure to connect your telephone to your modem: 2. Connect the telephone's modular cord into the PHONE jack on the back of your modem (see Figure 1-4). Lift your telephone’s handset and listen for a dial tone. Le 5634PEW Figure 1-4. Back of the modem 1.
S634PEW User's Manual 5634PEW Figure 1-5. Completed modem installation If you connected the modem to a computer, place the computer into terminal mode and complete the configuration information required by the software. Refer to your computer manual to find out the appropriate command to use. Then use the following procedure to verify that your connections: 1. Type AT and press the Enter key.
S634PEW U ! i 535s ans Your modem is now ready for operation. Refer to the manual that came with your communication software to begin communications. If you will be communicating directly with your modem, or if you want to find out more about the modem's operation, proceed to Chapter 2. :% Note: The voice function would not work without a sound card. Please make sure that your system contains a sound card before you record the greetings. 1.9 Modem Driver Installation ( PnP) 1. Turn on the computer.
5634PEW User's Manual Chapter 2 AT commands and Result Code Responses Chapter 2 describes the format to use when typing modem commands. Chapter 2 also describes the responses that your modem sends to your computer screen when you execute, or try to execute, modem commands. These commands are issued by using a data communications program. An example of such a program is Hyper Terminal, which is installed by Windows 95 when you install your modem hardware.
S034PEW Users Manual 7. Enter a number (for example, 555-1234) and click OK. Note: Before clicking OK, be sure the correct made is selected in the Phone Number dialog box. Select the modem from the Connect Using list. This opens the Connect dialog box. 8. Click Cancel. This closes the Connect dialog box, leaving the Hyper Terminal windows. You don't actually want to dial the number, you just want try out some AT commands. 9. Type AT&F and press the enter key.
5634PEW User's Manual 2.4 Basic AT Commands Command Function Al Persecute last command. A Go off-hook and attempt to answer a call B 0 Select V.22 connection at 1200bps or V.21 at 300bps. 1 Select Bell 212A connection at 120Qbps or Bell 103 at 300bps. (DEFAULT) Cc 1 Return OK message. D Dial the string of characters (0-9, A-D, #, or *) which can be modified by one of several modifiers listed below. 0-9 [Numbers 0-8 can be used when dialing pulse or tone. A-D. # *[A.
SO34PEW User's Manual Command | Function 0 0 Go online 1 Go online and initiate a long retrain sequence before returning to online data mode. 2 Go online and initiate a short retrain sequence before returning to online data mods. P Enable pulse dialing. Q 0 Send Result codes to DTE: (DEFAULT) 1 DO NOT send Result codes to DTE. Sn Select last S-Register to be accessed. Sn? Return the value of S-Register n. Sn=v Set default S-Register to value v. ? Re tum the value of last S-Register to be accessed.
5034PEW User's Manual 2.5 Extended AT Commands Command Function &C 0 Force ALSO (Carrier Detect) active regardless of the carrier state. (DEFAULT) 1 Allow LSD (Carrier Detect) to folio the carrier state being received. aD 0 Ignore DTR (assumed ON). (DEFAULT) 1 DTR going from ON to OFF forces the modem to command mode. 2 DTR going from ON to OFF forces the modem to go unhook {hang up). &F 0 Restore factory configuration 0. 1 Restore factory configuration 1. &J 0 Auxiliary never operated.
S634PEW User's Manual 2.6 Error Control and Data Compression Commands Command Function %C O Disable data compression. 1 Enable MNP 5 data compression. 2 Enable V.42bis data compression. 3 Enable both V.42bis and MNP 5 compression. (DEFAULT) Set maximum block size it MNP to 64. (DEFAULT) Set maximum block size in MNP to 128. Set maximum block size in MNP to 192, Set maximum block size in MNP to 256. \G Disable modem-to-modem XON/XOFF flow control. Enable modem-to-modem XON/XOFF flow control. ZEN \Ln NP block
5634PEW User's Manual 2.8 S-Registers Register Function Range Units Default SO Ring to auto-answer. 0-255 rings 0 S1 Ring counter. 0-255 rings 0 82 Escape character. 0-255 ASCII 43 83 Carriage return character. 0-127 ASCII 13(CR) $4 Line feed character, 0-127 Ascella 10(LF} $5 Backspace character. 0-32 ASCII 8(BS) SB Wait time for dial tone. 2-255 s 2 87 Wait time for carrier. 0-258 s 60 S8 Wait time for dial delay 0-255 s 2 modifier. $8 Reserved. $10 Carrier loss disconnect time. 1-256 0.
5634PEW User's Manual 2.9 Result Code Responses Verbose Number Description OK 0 Modem has successfully executed a command. CONNECT 1 Data connection has been made with a remote modem. RING 2 Modem has detected an incoming ring. NO CARRIER 3 Remote carrier signal was lost or not detected within the time limit specified by S-register S7. ERROR 4 Modem has found an error in your command line. CONNECT 1200 5 Modem has made a connection with a 1200 bps DTE rate. NO DIAL TONE 6 Modem has not detected a dial tone.
S5634PEW User's Manual Verbose Number Description CARRIER 7200 49 Modem has made a 7200 bps carrier connection. CARRIER 9600 50 |Modem has made a 9600 bps carrier connection. CARRIER 12000 51 [Modem has made a 12000 bps carrier connection. CARRIER 14400 52 [Modem has made a 14400 bps carrier connection. CARRIER 16800 53 [Modem has made a 16800 bps carrier connection. CARRIER 13200 54 I Modem has made a 19200 bps carrier connection. CARRIER 21600 55 |Modem has made a 21600 bps carrier connection.
S634PEW User's Manual Verbose Number Description CARRIER 31200 82 Modem has made a 31200 bps carrier connection. CARRIER 33600 83 |Modem has made a 33600 bps carrier connection. CONNECT 230400 84 Modem has made a connection with a 230400 bps DTE rate. CONNECT 86 Modem has made a connection with a bps DTE rate. CONNECT 34666 87 Modem has made a connection with a 34666 bps DTE rate. CONNECT 36000 88 |Modem has made a connection with a 3600Q bps DTE rate.
3634PEW User's Manual Verbose Number Description CARRIER 105 Modem has made a bps carrier connection. CARRIER 34666 106 [Modem has made a 34666 bps carrier connection. CARRIER 36000 107 |Modem has made a 36000 bps carrier connection. CARRIER 37333 108 [Modem has made a 37333 bps carrier connection CARRIER 38666 108 [Modem has made a 38666 bps carrier connection. CARRIER 110 |Modem has made a bps carrier connection. . CARRIER 41333 111 [Modem has made a 41333 bps carrier connection.
S634PEW User's Manual A FCC Compliance Appendix A provides compliance information about your modem. A.1 FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and.
S634PEW User's Manual This device complies with Part 15 of the FCC rules. Operation is subject ta the following two condition: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation. A.2 FCC Requirement This equipment complies with Part 68 of the FCC Rules. On the base unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Numbered) for this equipment.