User Manual IP™-Twelve 2-Channel Power Amplifier
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
WICHTIGE SICHERHEITSHINWEISE ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
INSTRUCTIONS IMPORTANTES DE SECURITE ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Lire ces instructions. Gardez ce manuel pour de futures références. Prétez attention aux messages de précautions de ce manuel. Suivez ces instructions. N’utilisez pas cette unité proche de plans d’eau. N’utilisez qu’un tissu sec pour le nettoyage de votre unité.
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela seca. 7. No bloquear ninguna de las salidas de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
Important Precautions This symbol is used to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This symbol is used to alert the user to the presence of “dangerous voltage” within the product enclosure that be of sufficient magnitude to constitute a risk of electric shock to persons. 8. Have gain controls on amplifiers turned down during power-up to prevent speaker damage if there are high signal levels at the inputs.
ENGLISH IP™-Twelve Power Amplifier Introduction Congratulations on your purchase of a Peavey Architectural Acoustics IP-Twelve power amplifier. Please read this manual carefully (especially the “Important Precautions” section located inside the front cover) as it contains information vital to the safe operation of the amplifier. Also, please fill out and return the enclosed product registration card.
1 4 2 5 1 TWELVE CH A CH B ACTIVE SIGNAL ACTIVE SIGNAL TEMP CLIP TEMP MODEL: IP-TWELVE BOTTOM CABINET IP-TWELVE SPRAY BLACK SCM: 660-180700-00 COLOUR: TEXT AND GRAPHICS SCREENED ON CHASSIS: PANTONE 645C GLOSSY BLUE & PEAVEY LIGHT GRAY DATE: 12 OCTOBER 2005 1 3 Front Panel CLIP 6 1 (1) Rack Mounting Ears 900 B REAKER 2 Two mounting holes are provided on each front mounting ear. D ESIGNED & E NGINEERED IN U.S.A.
TWELVE CH A CH B ACTIVE SIGNAL ACTIVE SIGNAL TEMP CLIP TEMP CLIP 5 6 MODEL: IP-TWELVE BOTTOM CABINET IP-TWELVE SPRAY BLACK SCM: 660-180700-00 COLOUR: TEXT AND GRAPHICS SCREENED ON CHASSIS: PANTONE 645C GLOSSY BLUE & PEAVEY LIGHT GRAY DATE: 12 OCTOBER 2005 900 2 B REAKER D ESIGNED & E NGINEERED IN U.S.A.
Operation AC Mains Circuit Size Requirements Power requirements for the IP-Twelve amplifier are rated at “idle”, 1/8th power (“typical” music conditions), 1/3rd power, and maximum rated power. The maximum power current draw rating is limited by the amplifier’s circuit breaker. Consult the specification sheet for the current that each amplifier will demand. AC mains voltage must be the same as that indicated on the back of the amplifier.
Operation Signal Mode Configuration The IP-Twelve amplifier is configured for Two-Channel (stereo), Bridged Mode, or Parallel Mode operation at the input connector. To send the same signal to both channels (Parallel Mode), connect the input signal to channel A via the input connector. Run jumpers from the positive and negative terminals of channel A’s input connector to the respective terminals of Channel B. Both channels then share channel A’s input signal, but will operate independently.
CONNECTIONS Speaker Output Connections Speakers are connected using the output barrier strip connectors. Spade lugs, ring tongues or bare wire may be connected to the output barrier strip elements. The barrier strip can accommodate up to a 10 gage wire per terminal. Make sure the amplifier is turned off before you change any output connections or jumpers. Consult the Wire Gauge Chart to find a suitable wire gauge to minimize losses of power in the speaker cables.
WIRE GAUGE CHART Cable Length Standard Wire Gauge Power Loss Power Loss Power Loss (4Ω) (2Ω) (Ft.) (AWG) (8Ω) 5' 18 AWG .79% 16 .5 1.0 2.0 14 .31 .62 1.24 12 .20 .40 .80 10 .125 .25 .50 10' 40' 80' 18 AWG 1.58% 3.16% 1.58% 3.16% 6.32% 16 1.0 2.0 4.0 14 .62 1.25 2.50 12 .40 .80 1.6 10 .25 .50 1.0 18 AWG 8.0% 12.6% 25.2% 16 4.0 8.0 16.0 14 2.5 5.0 10.0 12 1.60 3.2 6.4 10 1.0 2.0 4.0 8 .625 1.25 2.25 16 AWG 8.0% 14 5.0 10.0 20.
PROTECTION FEATURES The IP-Twelve incorporates protection features derived from Peavey’s extensive experience with reliability. The amplifiers are ruggedly built from high quality components and feature comprehensive protection circuits to protect your amplifier from those real world occurrences.
IP™-Twelve SPECIFICATIONS Rated Power 4 ohms bridge 1850 watts @ 1 kHz <0.1% THD Rated Power 2 x 2 ohms 900 watts per channel @ 1 kHz <0.05% THD both channels driven Rated Power 2 x 4 ohms 700 watts per channel @ 1 kHz <0.05% THD both channels driven Rated Power 2 x 8 ohms 450 watts per channel @ 1 kHz <0.05% THD both channels driven Rated Power 1 x 2 ohms 950 watts @ 1 kHz at <0.05% THD Rated Power 1 x 4 ohms 775 watts @ 1 kHz at <0.05% THD Rated Power 1 x 8 ohms 475 watts @ 1 kHz at <0.
IP™-Six SPECIFICATIONS Input Impedance 15k ohms, balanced Hum and Noise > -106dB, “A” weighted referenced to rated 8 ohm power Crosstalk > -55dB, “A” weighted referenced to rated 8 ohm power Current Draw @ 1/8 power 1,000 watts @ 2 ohms, 685 watts @ 4 ohms, 400 @ 8 ohms Current Draw @ 1/3 power 2,340 watts @ 2 ohms, 1,650 watts @ 4 ohms, 1,000 watts @ 8 ohms Idle Current Draw 30 watts Max. Current Draw 1752 watts @ 2 ohms, 1158 watts @ 4 ohms, 710 watts @ 8 ohms Thermal Emissions (BTU/hr.
Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301 601-483-5376 • Fax 601-486-1678 • http://aa.peavey.