Issue date: 12/4/2018 MINI EASY ONE BUTTON REMOTE CONTROL MEBT-1706 CONTENTS 1. Overview and features Page 2. 2. Diagrams Page 3. 3. Battery Page 4. 4. Pairing / Un-pairing device Page 7. 5. Scene setup / Scene control Page 14. 6. Operation Page 16. 7. Specifications Page 18. 8. Warning Page 19.
Issue date: 12/4/2018 1. Overview and features Easy one button remote control with 3 LED colour indication. (Red / Green / Amber). Equipped with 3 scene control and 1 ALL OFF control. New dimming method by holding down the button to take control of the load level. 3V CR2450 battery operation capable of 3 year battery life and built in battery low indictor. Main features of remote control; • • Compatible to current “Self Learning” system and the new M series. Easy freestanding on the table.
Issue date: 12/4/2018 2. Diagrams. Notes for the diagrams: Function Switch 1. Load Control 2. Scene Control 3.
Issue date: 12/4/2018 3. Battery Red LED will flash once every 4 seconds to indicate the battery is low. 1. With the one button remote control bottom facing up gently slide down the back cabinet. 2. Remove battery insulation strip.
Issue date: 12/4/2018 3. Or replacing a new battery use a slot screwdriver and push down the small metal spring then push out the battery. 4. Replace with a new 3V CR2450 battery making the positive symbol is facing upwards.
Issue date: 12/4/2018 5. Slide battery compartment upwards to complete the battery replacement. LITHIUM BATTERY CAUTION: Risk of Explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the environment protection rules.
8 Issue date: 12/4/2018 4. Pairing / Un-pairing Device PAIRING / UN-PAIRING Refer to the relevant receiver operation manual that you wish to control for detailed pairing / un-pairing procedure. With the receiver that you intent to use, enter into “Learning Mode” Function switch at position 1. To Pair: Press button once. Green LED flash once. LED Flash once To Un-Pair: Press button twice. Red LED flash twice.
9 Issue date: 12/4/2018 5. Scene Setup / Scene Control SCENE SETUP Mini one button remote control has built in 3 scene control which sends the unique special command to the M series receiver to call already stored scene memory from the receiver.
10 Issue date: 12/4/2018 3. Slide function switch to position 3. 4. Press button once to store Scene Status 1. 5. Green LED flash 3 times Amber LED flash 1 time to confirm Scene 1 is stored. LED 3 Times Scene 2 1. Function switch at position 1. 2. Set the desired load level status.
11 Issue date: 12/4/2018 3. Slide function switch to position 3. 4. Press button twice to store Scene Status 2. 5. Green LED flash 3 times Amber LED flash 2 times to confirm Scene 2 is stored. LED 3 Times Scene 3 1. Function switch at position 1. 2. Set the desired load level status.
12 Issue date: 12/4/2018 3. Slide function switch to position 3. 4. Press button 3 times to store Scene Status 3. 5. Green LED flash 3 times Amber LED flash 3 times to confirm Scene 3 is stored.
13 Issue date: 12/4/2018 Multiple receiver device setup with 2nd remote control: If you intend to set up multiple receiver device at the same time then you will need to use a 2nd remote control such as LYCT-505 or MYCT-1702 to set the load level. Firstly, make sure the 2nd remote control is also paired to each individual receiver device that the one button remote control is already paired to. Scene 1 1. With the 2nd remote control, set the desired load level status. 2.
14 Issue date: 12/4/2018 Scene 2 1. With the 2nd remote control, set the desired load level status. 2. On the one button remote control slide function switch to position 3. 3. Press button twice to store Scene Status 2. 4. Green LED flash 3 times Amber LED flash 2 times to confirm Scene 2 is stored. LED 3 Times LED 2 Times Scene 3 1. With the 2nd remote control, set the desired load level status. 2. On the one button remote control slide function switch to position 3. 3.
15 Issue date: 12/4/2018 SCENE CONTROL Function switch at position 2. Activate Scene 1: Press button once, Amber LED will flash 1 time to confirm. LED 1 Time Activate Scene 2: Press button twice. Amber LED will flash 2 times to confirm.
16 Issue date: 12/4/2018 Activate Scene 3: Press button 3 times. Amber LED will flash 3 times to confirm. LED 3 Times Deactivate Scene (ALL OFF): Long press button for 2 seconds. Red LED flash 2 times.
17 Issue date: 12/4/2018 6. Operation Mini one button remote control is compatible to M series receiver device and can control “Self Learning” system receivers as ON/OFF/Dimmer function however, scene control is not available. Please refer to the relevant user guide for detailed operation. SINGLE CONTROL Function switch at position 1. Turn the load ON: Press button once. Green LED flash once. LED Flash once Turn the load OFF: Press button twice. Red LED flash twice.
18 Issue date: 12/4/2018 Dim the load: 1. Press button once to turn ON load. 2. Press and hold down button again to start dimming, load will start to adjust. 3. Green LED will quick flash until button is released. LED Quick flash 4. At the desired level release button to stop. During dimming process when the load level reaches to the lowest or brightest, to continue dimming release button then press button again to start dimming.
19 Issue date: 12/4/2018 7. Specifications Battery: Radio Frequency: 3V CR2450 Lithium Cell Battery 433.92MHz Power consumption: 1W Operation Temperature: Range: 0-40 ºC up to 50 m indoors (Depends on building materials) Low Voltage Directive 2014/35/EU RED Directive 2014/53/EU The CE marked affixed to this product confirms Its complaisance with the European Directives Which apply to the product and in particular its compliance with the harmonizes standards and specifications.
20 8. Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
