E-Guardian S409 Mask & Fever Detection Solution Quick Installation Guide
Draft Version Copyright Notice ©2020 All Rights Reserved. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Disclaimer The S409 Preliminary Fever Detection Solution is not intended to replace professional medical device.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
System Overview The S409 mask and fever screening detection solution is designed for fast preliminary detection of potential fever symptoms. The S409 comprises of the following main components: • Thermal camera: An infrared thermography camera to detect potential fever. A temperature of >37.5°C is defined as potential fever with S409. • Calibrator: To calibrate the thermography camera to enhance the accuracy.
How the S409 Works AI-Powered Human Recognition The S409 is an AI-powered solution so it is able to recognize a human from the thermal image and thus measuring the forehead temperature and mask. An individual wearing a mask can still be detected. Real-time On-Screen Display The S409 continuously measures the temperature and mask of people passing through the S409. Detection results are displayed real-time on the screen.
Installation Options Designed for flexible installation, the S409 comes with an all-in-one installation kit to support various installations. A. VESA Mount S409 can be installed on the VESA kit for the vehicle application. Optional VESA mount kit B. Tripod Mount S409 can be installed on the tripod with an universal 1/4" threaded tripod socket for installation on a tripod.
Package Contents Package Contents • S409 (including power cord and S409.
Getting Started Before installation, please get yourself familiar with the components of the S409.
Getting Started Rear View LED Indicator Status Power LED Network LED Thermal Detection LED 6
Getting Started Bottom View 1/4" Thread and VESA mount Power connector LAN port USB port Side View SIM Card and Memory Card slots 7
132.9 Dimension 158.3 196.5 177.
Installation Advice Before proceeding to install the S409, please follow the guidelines below to get the optimal performance of the system: • Install the S409 indoor with ambient temperature of 15~30°C. • For the person to be detected, it’s suggested to stand at a distance of 1M~1.5M to the S409. • To avoid detection interference, prevent other heating source such as fluorescent or lamp from being constantly displayed in the S409's field of view.
Installation Advice • The S409 is capable of detecting multiple human temperatures. However, avoid overlaps between people to ensure the measurement. For optimal performance, it's suggested that you allow only one person appear in the field of view at a time.
Installations Installing the S409 – Vehicle Please follow the steps as below to install the S409 in vehicle: 1. Locate the VESA hole in the bottom of the S409 mounting plate, and install 4 M3*L9 screws on the S409. 2. Tighten 4 M6*30 screws for two pairs of pipe clamps. The lower pipe clamp is about 125cm away from the car floor, and the distance between the two pipe clamps is about 10cm.
Installations 3. Tighten 2 M6*10 screws for racket/device on the pipe to secure the position. 4. Adjust the angle of S409 to 15 degrees to screen passengers in the vehicle. Then tighten the screws in the picture as left. Cautions: • DO NOT expose the S409 to direct sunshine, water, oil, dust or corrosive gas.
Installations Mounting the S409 – Tripod Mount 1. Locate the threaded hole in the bottom of the S409 mounting plate. 2. Mount your tripod head to S409 plate. Tighten the screw-head from the bottom of the tripod head to secure the assembly. Then mount it to your tripod. 3. Adjust the angle and the height of the tripod to ensure the S409 and person to be detected are in the camera's field of view.
Installations 4. Connect the power cord of the provided power adapter to the power connector on S409. Then plug the power adapter into a power outlet. (use a coordinate plug adapter for your territory) The power of S409 will startup automatically. (Please note that S409 will cause auto shut down after 10 seconds by itself if the power is unplugged.) Cautions: • DO NOT expose the S409 to direct sunshine, water, oil, dust or corrosive gas.
Installations Power Connection 1. The S409 come with a Type-U (or M8 to DC) power cord for power source. 2. Attach the correct plug according to your location to the power adapter. Then plug the power adapter into a standard AC power outlet. 3. When power is applied, the S409 will power on automatically. Then the S409 will launch the Fever and Mask Detection APP automatically upon startup.
Using S409 When a person's temperature is detected under 37.5°C, "PASS" will be displayed; otherwise, "OUT OF TEMP" will be displayed and a sound alert will be sent. If the person did not wear the mask, the screen would show "NO MASK" and a sound alert will be sent. When S409 detects the mask and the temperature is under 37.5, the monitor will show a green "PASS" sign. If the temperature is over 37.5, the monitor will show a red "OUT of TEMP" sign.
Adjust the Volume If usrs need to adjust the volume of the audio, follow the insutreuction as below: • Slide down the menu 17
Adjust the Volume 18
Adjust the Volume • 19
Screen Mirroring Wireless screen Mirroring is available for the S409. It's a suitable invehicle environment. Please follow the instruction for the screen mirroring.
Screen Mirroring 21
Screen Mirroring Then choose your devices. The screen on the S409 can be mirrored on your display device. (Please note that screen mirroring may not be supported depending on your model or brand of display devices.
Specifications Specifications Highlight Measuring Distance 1M ~1.5M Accuracy ±0.5ºC System Power 12V/24V, 3A Touch Screen 5" Capacitive touch screen Control Power button O.S Android 11.0 Thermal Imaging Lepton 2.5 Array Format 80 x 60 Calibration Blackbody, ±0.3ºC Dimension 196.36 x 132.86 x 157.61 mm (W x H x D) Weight 920g Working Temp. 15 ~ 30 °C Storage Temp.
Q&A 1. Q: What will the device do A: When users are not in mask when subjects not in masks and have fever simultaneously, the device will say "Abnormal temperature". 2. Q: Can the device scan a QR A:The QRCode scanning function code?. is not built in the S409. 3. Q: Can one device detect moreA: It is recommended to set up than two people at the samea single gateway to detect one time in a large field site. person at a time when developing S409.