Key function 1. Power button Press it to “ON” Press & hold it for 5sec to “OFF” 1 2. Mode change button To change diagnosis process Moisture -> Wrinkle (30X) -> Evenness (60X) > Pore (60X) -> Pigmentation (60X PL) -> 1X lens 2 3. LED light mode change button Only used in 1X lens mode In the album, it is move key to select another image 3 4 5 6 5 7 4.
Moisture Check 1 To check moisture, Simply place moisture sensor area to skin And press button 3. There are four round shaped metal in the lens part, above two metals “1” are moisture sensor 2 The test result will be displaced as shown as “2” moisture sensor 3 3 Please press “M” button to move to next step.
Wrinkle Check X30 Capture the image by “1” Re-activate & re-capture press “1” Diagnosis process will be done in 1) PDA ( which has Blue tooth ) 2) PC ( Blue tooth ) Or captured image will be saved in external memory such as SD or Mini SD card then it can be inserted into PC to perform the analysis 1 Diagnosis software can be provided – depends on project. 1 Auto-focus function- press “1”. Capture – press “1” for 2 sec. 4 Please press “M” button to move to next step.
Album ( 4 images view ) Captured image is saved in Album Go to Album, press “3” when the camera is activating When album is shown, “4” images will shown Press “1” selected image will be shown in “Full Screen” 2 3 4 1 5 In 4 images view, press “2” or “3” to select other images In 4 images view & one image view, press “4” to transfer the image to external device and press “5” to delete selected image 5
Album ( 1 images view ) Captured image is saved in Album Go to Album, press “3” when the camera is activating When album is shown, “4” images will shown Press “1” selected image will be shown in “Full Screen” 2 3 In 4 images view, press “2” or “3” to select other images In 4 images view & one image view, press “4” to transfer the image to external device and press “5” to delete selected image 6 4 1 5
Evenness Check X60 From “Wrinkle” check to “Evenness” check process, press “M” to change 1 Capture the image by “2” Re-activate & re-capture press “2” 2 2 Please press “M” button to move to next step.
Pore Check X60 From “Evenness” check to “Pore” check process, press “M” to change Capture the image by “2” Re-activate & re-capture press “2” 2 2 Please press “M” button to move to next step.
Spot Check X60Polarizing mode From “Pore” check to “Spot” check process, press “M” to change Capture the image by “2” Re-activate & re-capture press “2” 2 2 Please press “M” button to move to next step.
X1 Client’s profile From “Spot” check to “X1 lens to take client picture”. process, press “M” to change Capture the image by “2” Re-activate & re-capture press “2” Operating frequency: 2400-2483.5 MHz Operating voltage : DC 3.7V Li-ion Battery Operating temperature : -10℃ ~ 50℃ 2 10 Please press “M” button to move to first step.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT Safety Instruction: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this equipment near water. 6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce heat.