User's Guide

LED DESK LAMP
WITH WIRELESS CHARGING
User’s Guide
Getting Started
Step 1: Plug In
1. Plug the included power adapter into the
power jack on the back of the lamp.
2. Plug the other end of this cable into a working
power outlet.
BATTERY BACKUP
Your clock has a pre-installed battery backup that will keep the time
in case power is interrupted (like by a power outage, for example). To
start using the battery backup, pull the activation tab above the battery
door on the back of the lamp. The protective film covering the battery
will come of with the tab and the battery will be activated.
If you notice that battery backup is no longer working, simply replace
the CR2032 coin-cell battery in the battery compartment on the back of
the lamp. Use a coin to turn the battery door and unlock it. Then remove
the door and access the CR2032 battery.
Lamp, back
panel
Step 2: Unfold and turn on the lamp
This lamp has 2 articulating arms
for complete flexibility in angle and
placement. Unfold the lamp completely
and experiment with both arms until you
find the position and angle you prefer.
To turn on the lamp: Press
on the
base of the lamp.
Step 2: Set the Time and Date
When you first plug it in, the lamp’s clock
display shows 12:00.
1. Press
on the back of the lamp.
2. Press
and on back of the lamp
to adjust the hour. Press to set
the hour and move to the minutes.
3. Press
and to adjust the minutes.
Press
to set the minutes and
move to the year.
Lamp, back
panel
4. Press and to adjust the year. Press to set the year and move to the date.
5. Press
and to adjust the date. Press to finish setting the time and date.
Note: By default, the clock uses the 12-hour format (for example, 5:00 pm instead of
17:00). To switch between 12- and 24-hour format, press
.
Everyday Use
Setting the Alarm
1. Press on the back of the lamp to display the alarm time.
2. Press
on the back of the lamp to adjust the alarm time.
3. Press
and on back of the lamp to adjust the alarm hour.
Press
to set the hour and move to the minutes.
4. Press
and to adjust the alarm minutes. Press to set
the minutes and move to the snooze time.
5. Press
and to adjust the amount of alarm delay for snooze.
Lamp, back
panel
Press to set the snooze time and move to the alarm sound/
music.
6. Press
and to select the sound/music you want to use for the alarm. Press
to select it and finish setting the alarm.
To turn the alarm on/off: Press
on the back of the lamp to display the alarm time.
Then press and on back of the lamp to turn on the alarm and/or snooze function.
• One press turns on the alarm.
• Two presses turns on the alarm and snooze function (alarm sounds for one
minute, then snoozes).
• Three presses turns off alarm and snooze.
Note: The alarm sounds for 1 minute when activated.
Setting the Display Brightness
The clock display defaults to its highest brightness setting when you first plug the
lamp in.
To adjust display brightness: Press
on the back of the lamp. Each press goes to
the next setting—minimum, medium, and maximum.
Using the Lamp
The lamp offers 5 brightness levels and 3 color temperature settings.
To turn on the lamp: Press
on the base of the lamp.
To adjust the lamp’s brightness: Press
and on the base of the lamp.
To adjust the lamp’s color temperature: Press
on the base of the lamp. Each
press goes to the next temperature setting (cool, warm, and neutral).
Charging your Device
Charging
indicator
IMPORTANT: Before you try to charge your
device, make sure it is compatible with
wireless charging. If your device has a metal
case, remove it before you put the device on
the charger.
1. Place your wireless charging-compatible
device directly onto the charging pad on
base of the lamp. Refer to the placement
illustration here as a guide.
Lamp,
base