ITEM #0007224 0749753 0368939 0749677 0007631 0749676 BATHROOM FAUCET AquaSource® is a registered trademark of LF, LLC. All Rights Reserved. MODEL #67307-5001 67307W-5001 67307-5002 67307W-5002 67307-5004 67307W-5004 Francias / Español p. 10 ATTACH YOUR RECEIPT HERE Serial Number ____________ Purchase Date ____________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday. Lowes.
PACKAGE CONTENTS E F A F N N O O P JJ Q B G H C T W S S D V X U M M I I R L K PART DESCRIPTION QUANTITY A Spout 1 B C D E Rubber Washer (Preassembled to Faucet (A)) Metal Washer (Preassembled to Faucet (A)) Retaining Nut (Preassembled to Faucet (A)) Hot End Valve 1 1 1 1 F Cold End Valve 1 G H I J Washer (Preassembled to Hot End Valve (E) and Cold End Valve (F)) Bracket (Preassembled to Hot End Valve (E) and Cold End Valve (F)) Locking Screw (Preassembled to Bracket (H)
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. WARNING: Follow the installation instructions carefully. Proper installation is the installer’s responsibility. Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury. CAUTION: Check local building codes before beginning installation to ensure compliance.
ASSEMBLY INSTRUCTIONS 2. Install the spout (A): 2 a. Remove the preassembled rubber washer (B), metal washer (C), and retaining nut (D) from the spout (A) and place the spout (A) through the center hole of the sink. A b. From underneath the sink, thread the rubber washer (B), metal washer (C), and retaining nut (D) onto the spout (A) and tighten securely. B C D 3. Install the hot and cold end valves (E and F). 3 a.
ASSEMBLY INSTRUCTIONS 5. Connect a 1/2 in. IPS faucet connector or coupling nuts (not included) with 3/8 in. O.D. ball-nose risers (not included) to the water supplies underneath the sink using wrenches (not included). 5 Note: Refer to local plumbing codes for permissible types of water supply connectors. 6. Before tightening the faucet connector to the water supply, apply a second wrench to the supply tube This will prevent the supply tube from moving or twisting when tightening the faucet connector.
ASSEMBLY INSTRUCTIONS 8. Apply silicone sealant (not included) to the underside of the (O). 8 O 9. Insert the pop-up body (R) into the sink and screw the (O) onto the pop-up body (R). Ensure the pivot hole is facing the back of the sink. Tighten the nut (Q) and remove the pivot nut (S). 9 O Q S R 10. Insert the stopper (N) onto the sink. Remove the preassembled horizontal rod (T) and clip (U) from the lift rod strap (W).
ASSEMBLY INSTRUCTIONS 11. Re-attach the lift rod strap (W) to the horizontal rod (T) using the clip (U). 11 W U T 12. Insert the lift rod (X) through the spout (A) and into the lift rod strap (W). Tighten the screw (V) on the lift rod strap (W). 12 X A V W OPERATING INSTRUCTIONS 1. After the installation is complete: 1 a. Remove the aerator from the faucet (A) using a coin (not included). b. Turn on the water supply and allow both hot and cold water to run for at least one minute each. A c.
CARE AND MAINTENANCE Clean carefully by gently wiping with a grit-free damp cloth. Use only mild soap with water. Never use acids, harsh chemicals, or abrasive detergents to clean the surface. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION There is a leak from under the handle or there is a leak from the spout when the faucet is off. 1. The bonnet nut is not tight enough. 1. Remove the handle and retighten the bonnet nut. 2. The cartridge is damaged. 2.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
