ITEM #0007224 0368939 0007631 2-HANDLE 8 IN. WIDESPREAD LAVATORY FAUCET AquaSource® is a registered trademark of LF, LLC. All Rights Reserved. MODEL #67307-5001 67307-5002 67307-5004 Français p. 9 Español p. 17 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
PACKAGE CONTENTS E A J G H I N F Z O B C D Q R P S M U Y X V T W L K PART A B C D E F G H I J K L M DESCRIPTION Spout Rubber Washer (Preassembled to Faucet (A)) Metal Washer (Preassembled to Faucet (A)) Retaining Nut (Preassembled to Faucet (A)) Hot End Valve Cold End Valve Washer (Preassembled to Hot End Valve (E) and Cold End Valve (F)) Bracket (Preassembled to Hot End Valve (E) and Cold End Valve (F)) Locking Screw (Preassembled to Bracket (H)) Block (Preassembled to Faucet (A)ǃHot E
PACKAGE CONTENTS PART N O P Q R S T U V W X Y Z DESCRIPTION Stopper Flange Pop-up Body Gasket (Preassembled to Pop-up Body (P)) Nut (Preassembled to Pop-up Body (P)) Pivot Nut (Preassembled to Pop-up Body (P)) Lift Rod Strap Horizontal Rod (Preassembled to Lift Rod Strap (T)) Strap (Preassembled to Lift Rod Strap (T)) Clip (Preassembled to Lift Rod Strap (T)) Screw (Preassembled to Lift Rod Strap (T)) Lift Rod Aerator Tool QUANTITY 1 1 1 1 1 1 1 1 1 1 1 1 1 SAFTEY INFORMATION Please read and understand
ASSEMBLY INSTRUCTIONS 1. Shut off water supplies. Remove old faucet. 1 2. Place spout (A) through center mounting hole of sink (not included). Secure spout (A) with rubber washer (B), metal washer (C) and retaining nut (D). 2 A B C D 3. Slide hot end valve (E) and cold end valve (F) through sink mounting holes. Make sure long tubes are installed away from the spout (A). Handles should point out when in off position. Secure hot end valve (E) and cold end valve (F) with washers (G) and brackets (H).
ASSEMBLY INSTRUCTIONS 5. Connect 1/2 in. IPS faucet connector or coupling nuts (not included) with 3/8 in. O.D.ball-nose risers (not included) to water supplies using wrenches (not included). Note: Refer to local plumbing codes for permissible types of water supply connectors. 5 6 6. Remove stopper (N) and flange (O). Screw nut (R) all the way down. Push gasket (Q) down. N O Q R 7 S IL ICO NE 7. Apply silicone or putty (not included) to underside of flange (O). O 8.
ASSEMBLY INSTRUCTIONS 10 10. Install horizontal rod (U) through the hole of stopper (N). Hand tighten pivot nut (S). N U S 11 11. Attach horizontal rod (U) to strap (V) using clip (W). V U W 12 12. Insert lift rod (Y) through faucet and into strap (V). Tighten screw (X). Y X V 13 13. After installation is completed, remove aerator on spout (A) using aerator tool (Z). Turn on water supply and allow both hot and cold water to run for at least one minute each.
CARE AND MAINTENANCE &OHDQ FDUHIXOO\ E\ JHQWO\ ZLSLQJ ZLWK D JULW IUHH GDPS FORWK 8VH RQO\ PLOG VRDS ZLWK ZDWHU 1HYHU XVH DFLGV KDUVK FKHPLFDOV RU DEUDVLYH GHWHUJHQWV WR FOHDQ VXUIDFH TROUBLESHOOTING ,I \RX KDYH DQ\ TXHVWLRQV UHJDUGLQJ WKH SURGXFW SOHDVH FDOO RXU FXVWRPHU VHUYLFH DW D P S P (67 0RQGD\ )ULGD\ PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION /HDN IURP XQGHU KDQGOH 'DPDJHG FDUWULGJH 5HPRYH KDQGOH 5HSODFH FDUWULGJH ,QFRQVLVWHQW IORZ SDWWHUQ $HUDWRU
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.