Homekit无线开关说明书V3 尺寸:65*65mm 材质:105g太空梭哑粉 工艺:胶装 料号:3020212 PANTONE COOL GRAY 7C PANTONE COOL GRAY 2C PANTONE 299C
Wireless Mini Switch T1
Wireless Mini Switch T1 Quick Start Guide English Product Introduction Reset Button Long Press for 5s: Reset/Connect to Network Single Press: Effective Range Test/Identify Device Push Button Indicator Light * This device requires a compatible Zigbee 3.0 hub. Some features require a specific hub. For a detailed list, visit www.aqara.com/support.
English Quick Setup 1. Please add the Hub to the app according to the Hub Quick Start Guide. 2. Please open the app, tap “Home” and then tap “+” at the top right corner to enter “Add Device (Accessory)” page. Select “Wireless Mini Switch T1”, and add it according to instructions. 3. Need help? Visit www.aqara.com/support. * If the connection fails, please move the device closer to the Hub and try again.
Option 1: Place it directly on the desired position. English Option 2: Remove the protective film, and stick it to the desired position. * Keep the surface clean and dry.
English Specifications Model: WMS-R01 Dimensions: 45 × 45 × 12 mm (1.77 × 1.77 × 0.47 in.) Wireless Protocol: Zigbee 3.0 Battery: CR2032 Operating Temperature: -10° - +50℃ (14° - 122℉) Operating Humidity: 0 - 95% RH, non-condensing * Read this Quick Start Guide carefully before use and keep it for future reference.
無線開關 T1使用說明書 產品介紹 按鍵 指示燈 * 本產品需要配合具備Zigbee 3.0閘道器功能的設備使用。部分功能 需要特定型號閘道器支援,詳情列表請查看:www.aqara.
繁體中文 快速設定 1、請依照閘道器說明書,將閘道器添加到app; 2、開啓app,點選首頁右上角「+」,進入「添加設備(配 件)」頁面,選擇無線開關 T1,並依照提示進行操作; 3、如需幫助請查詢:www.aqara.
方式二:撕下膠貼保護膜,粘貼在所需位置。 繁體中文 *請確保粘貼位置表面清潔乾燥。 基本參數 產品型號:WMS-R01 產品尺寸:45×45×12公釐(1.77×1.77×0.47英吋) 無線連接:Zigbee 3.
Kabelloser Minischalter T1 Schnellstartanleitung Deutsch Produktübersicht Rücksetztaste Langer Tastendruck 5 Sek: Netzwerk zurücksetzen/verbinden Einmal drücken: Test Empfangsbereich/Gerät identifizieren Taste Anzeigelampe * Für dieses Zubehör wird ein kompatibler Zigbee 3.0-hub benötigt. Für einige Funktionen wird ein spezifischer hub benötigt. Die detaillierte Liste dazu finden Sie hier: www.aqara.com/support.
Schnelleinrichtung * Wenn die Verbindung fehlschlägt, geben Sie bitte das Zubehör näher an den Hub und versuchen Sie es erneut. Montage Test der wirksamen Reichweite: Drücken Sie einmal die Rücksetztaste des Zubehörgeräts an dessen gewünschtem Standort. Wenn der Hub Töne von sich gibt, bedeutet dies, dass das Zubehör mit dem Hub korrekt kommunizieren kann. Deutsch 1. Bitte fügen Sie den Hub entsprechend der Hub-Schnellstartanleitung zur App hinzu. 2.
* Vermeiden Sie die Nähe von Metalloberflächen, um die Signalstärke zu maximieren. Deutsch Option 1: Legen Sie ihn direkt an die gewünschte Stelle. Option 2: Entfernen Sie die Schutzfolie und kleben Sie ihn an die gewünschte Stelle.
* Halten Sie die Oberflächen sauber und trocken. Spezifikationen * Lesen Sie bitte die Schnellstartanleitung vor der erstmaligen Verwendung und bewahren Sie sie auf. Deutsch Modell: WMS-R01 Abmessungen: 45 × 45 × 12 mm (1,77 × 1,77 × 0,47 Zoll) Drahtloses Protokoll: Zigbee 3.
Guide de démarrage rapide du mini commutateur sans fil T1 Présentation du produit Bouton de réinitialisation Appui prolongé (5 secondes): Réinitialisation/Connexion au réseau Un seul appui: Essai de portée réelle/dentification de l'appareil Français Bouton poussoir Voyant indicateur * Cet accessoire nécessite d'un hub compatible Zigbee 3.0. Certaines fonctions exigent un hub spécifique. Vous trouverez une liste détaillée sur le site www.aqara.com/support.
Configuration rapide 1. Ajoutez le concentrateur à l'application conformément au guide de démarrage rapide du concentrateur. 2. Ouvrez l'application, touchez «Home» (Maison) puis touchez «+» au coin supérieur droit pour entrer à la page «Add Device (Accessory)» (Ajouter un périphérique (accessoire)). Sélectionnez «Wireless Mini Switch T1» (Mini commutateur sans fil T1) et ajoutez-le comme indiqué dans les instructions. 3. Vous avez besoin d'aide? Visitez www.aqara.com/support.
* Évitez les surfaces métalliques qui peuvent affaiblir le signal. Option 1 : Placez-le directement à l'endroit voulu. Français Option 2: Enlevez le film de protection et collez-le directement à l'endroit voulu. * Maintenez la surface propre et sèche.
Caractéristiques Modèle: WMS-R01 Dimensions: 45 × 45 × 12 mm (1,77× 1,77 × 0,47 in) Protocole sans fil: Zigbee 3.0 Pile: CR2032 Température de service: de -10 à +50 ℃ (de 14 à 122 ℉) Humidité de service: de 0 à 95% HR, non condensante * Lisez attentivement ce guide de démarrage rapide avant d'utiliser l'appareil, et conservez-le pour pouvoir le consulter ultérieurement.
Guía rápida del mini switch inalámbrico T1 Presentación del producto Botón de restablecimiento Pulsación larga durante 5 seg: restablecer/conectarse a la red Una pulsación: prueba de alcance efectivo/identificación de dispositivos Botón Español Luz indicadora * Este accesorio requiere un Zigbee 3.0 hub compatible. Algunas funciones requieren un hub específico. Consulte una lista detallada a continuación: www.aqara.com/support.
Configuración rápida 1. Siga las instrucciones en la Guía rápida del Hub para añadir el Hub a la aplicación. 2. Abra la aplicación, pulse “Home” (Casa) y luego “+” en la parte superior derecha para acceder a la página “Add Device (Accessory)” (Añadir dispositivo [Accesorio]). Seleccione “Wireless Mini Switch T1” (Mini switch inalámbrico T1) y siga las instrucciones para añadirlo. 3. ¿Necesita ayuda? Visite www.aqara.com/support.
Opción 1: Colóquelo directamente en la posición deseada. Español Opción 2: Retire el film protector y adhiéralo en la posición deseada. * Mantenga la superficie limpia y seca.
Especificaciones Modelo: WMS-R01 Dimensiones: 45 × 45 × 12 mm (1,77× 1,77 × 0,47 pulgadas) Protocolo inalámbrico: Zigbee 3.0 Batería: CR2032 Temperatura de funcionamiento: -10° - +50℃ (14° - 122℉) Humedad de funcionamiento: 0 - 95% HR, sin condensación * Lea esta guía rápida detenidamente antes de utilizar el producto y consérvela para futuras consultas.
Mini-interruttore Wireless T1 Guida di avvio rapido Presentazione del prodotto Tasto Reset (Ripristina) Pressione lunga per 5s: Resettare/Collegare alla rete Singola pressione: Test della gamma effettiva/Identificare dispositivo Italiano Pulsante a pressione Spia sensore * Questo dispositivo richiede un hub compatibile con Zigbee 3.0. Alcune funzioni richiedono un hub specifico. Per un elenco dettagliato invitiamo a consultare il sito www.aqara.com/support.
Configurazione rapida 1. Si prega di aggiungere l’Hub all’app in linea con quanto definito nella guida di avvio rapido dell’hub. 2. Aprire l’app, toccare “Home” e poi toccare “+” sull’angolo superiore destro per accedere alla pagina “Aggiungi dispositivo (Accessorio)”. Selezionare “Mini-interruttore Wireless T1”, e aggiungerlo seguendo le istruzioni. 3. Serve aiuto? Visita il sito www.aqara.com/support. * Qualora la connessione non vada a buon fine, avvicinare il dispositivo all’Hub e riprovare.
Opzione 1: Collocarlo direttamente nella posizione desiderata. Italiano Opzione 2: Togliere la pellicola protettiva e fissarla nella posizione desiderata. . * Mantenere la superficie pulita e asciutta.
Specifiche Modello: WMS-R01 Dimensioni: 45 × 45 × 12 mm (1.77 × 1.77 × 0.47 in.) Protocollo Wireless: Zigbee 3.0 Batteria: CR2032 Temperatura de funcionamiento: -10° - +50℃ (14° - 122℉) Humedad de funcionamiento: 0 - 95% RH, non-condensing * Leggere attentamente questa Guida rapida prima dell'uso e conservarla per riferimenti futuri.
Краткое руководство по эксплуатации беспроводной мини-выключатель T1 русский Описание продукта Описание продукта Длительное нажатие в течение 5 с: Сброс/Подключение к сети Однарное нажатие: Тест рабочего диапазона/Определение устройств Кнопка Световой индикатор * Для работы данного аксессуара требуется совместимый Zigbee 3.0 контроллер. Для некоторых функций требуется специальный контроллер. Подробнее см. на веб-сайте: www.aqara.com/support.
Быстрая настройка * В случае сбоя соединения принадлежность следует переместить ближе к хабу и повторить попытку. Монтаж Проверка эффективной дальности действия: Однократно нажмите кнопку сброса на принадлежности в требуемом месте. Если хаб подает голосовые инструкции, значит принадлежность эффективно обменивается данными с хабами. русский 1. Добавьте хаб к приложению согласно краткому руководству по эксплуатации хаба. 2.
* Для максимальной эффективности передачи сигналов избегайте металлических поверхностей вблизи устройств. русский Вариант 1: Разместите его непосредственно в требуемом месте. Вариант 2: Снимите защитную пленку и приклейте непосредственно в требуемом месте. * Поверхность должна быть чистой и сухой.
Спецификации Модель: WMS-R01 Габариты: 45 × 45 × 12 мм (1,77 × 1,77 × 0,47 дюймов) Протокол беспроводной связи: Zigbee 3.0 Батарея: CR2032 Температура эксплуатация: -10° - +50℃ (14° - 122℉) Рабочая влажность: 0 - 95% RH, без конденсации * Внимательно прочтите это краткое руководство перед началом русский эксплуатации и сохраните его для дальнейшего использования.
日本語 製品紹介 ワイヤレス・ミニ・スイッチT1 クイックスタートガイド リセットボタン 5秒間押し続ける: リセット/ネットワークへ接続 一回押す:動作範囲試験/デバイスの検出 プッシュボタン インジケータライト * 本アクセサリは互換のZigbee 3.0ハブを必要とします。 一部の機能は特 定のハブが必要です。 詳細はこちらをご覧ください:www.aqara.
クイック設定 *接続がうまくいかない場合、 アクセサリをハブに近づけて、 再度お試しください。 インストール 検出範囲のテスト:所望の位置にて、 アクセサリ上のリセット ボタンを一回押します。 ハブが音声プロンプトを流せば、 アク セサリがハブと通信可能であることを示します。 *信号強度を最大限に保つため、金属面は避けてください。 日本語 1、ハブのクイックスタートガイドを参照して、 ハブをアプリに 加えてください。 2、アプリを開き、 「Home」 (ホーム)をタップした後、上右隅の 「+」をタップして 「Add Device (Accessory)」 (デバイス (ア クセサリ)を追加)ページへ進みます。 「Wireless Mini Switch T1」 (ワイヤレス・ミニ・スイッチT1)を選び、指示に 従い追加します。 3、ご質問がおありですか?www.aqara.
日本語 オプション1:所望の位置へ直接配置します。 オプション2:保護フィルムを外し、所望の場所へ直接貼り付 けて固定します。 *乾燥した清潔な配置面を選んでください。
仕様 * 使用前に本クイックスタートガイドを注意深く読み、将来の参考用に保管 してください。 日本語 モデル:WMS-R01 寸法:45×45×12mm ワイヤレス通信規格:Zigbee 3.
한국어 무선 미니 스위치 T1 빠른 시작 안내서 제품 소개 리셋 버튼 5초간 길게 누름: 재설정/네트워크로 연결 한 번만 누름: 효력 범위 테스트/장치 식별 누름 버튼 지시등 * 이 액세서리에는 호환 가능한 지그비 3.0 허브가 필요합니다. 일부 기능에는 특정 허브가 필요합니다. 세부 목록에 대해서는 www.aqara.com/support를 참조합니다.
빠른 설정 * 연결이 되지 않는 경우, 액세서리를 허브에 더 가까이 이동시켜서 다시 시도해 주십시오. 설치 유효 범위 테스트: 원하는 위치에서 액세서리의 리셋 버튼을 한 차례 누릅니다. 허브에 음성 프롬프트가 나타나는 경우, 액세서리가 허브와 유효하게 통신할 수 있다는 것을 나타냅니다. * 신호 강도를 극대화하려면 금속 표면에 놓지 마십시오. 한국어 1. 허브 퀵 설치 가이드에 따라 허브를 앱에 추가해 주십시오. 2. 앱을 열고 “Home” (홈) 을 탭한 다음에 오른쪽 상단 구석의 “+” 를 탭하여 “Add Device (Accessory)” (장치 추가(액세서리)) 페이지로 들어갑니다. “Wireless Mini Switch T1” (무선 미니 스위치 T1) 를 선택하고, 지시에 따라 추가합니다. 3. 도움이 필요하신가요? www.aqara.com/support를 방문해 주세요.
한국어 옵션 1: 원하는 위치에 직접 놓습니다. 옵션 2: 보호 필름을 제거하고 원하는 위치에 붙입니다. * 표면을 깨끗하고 건조된 상태로 유지합니다.
사양 * 사용 전에 주의하여 이 빠른 시작 안내서를 읽고 향후 참조를 위해 보관합니다. 한국어 모델: WMS-R01 제원: 45 × 45 × 12mm (1.77 × 1.77 × 0.47인치) 무선 프로토콜: Zigbee3.
FCC ID: 2AKIT-AR001 Federal Communications Commission (FCC) compliance statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
CAUTION: RISK OF EXPLOSION IF REPLACED BY AN INCORRECT TYPE. BATTERY IS DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. RECYCLING. This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
Complies with the European Union’s Restriction of Hazardous Substances Directive which protects the environment by restricting specific hazardous materials and products.
Warnings 1. This product is NOT a toy. Please keep children away from this product. 2. This product is designed for indoor use only. Do NOT use in humid environments or outdoors. 3. Beware of moisture, do NOT spill water or other liquids onto the product. 4. Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation. 5. Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional. 6.
Avertissements 1. Ce produit N'EST PAS un jouet Maintenez-le hors de portée des enfants. 2. Cet appareil ne doit être utilisé qu'à l'intérieur. Ne l'utilisez PAS à l'extérieur ou dans des environnements humides. 3. Méfiez-vous de l'humidité, et n'éclaboussez pas l'appareil d'eau ni d'autres liquides. 4. Ne placez PAS ce produit près d'une source de chaleur. Ne le mettez PAS dans un lieu clos, à moins qu'il ne soit suffisamment ventilé. 5. N'essayez PAS de réparer vous-même cet appareil.
Advertencias 1. Este producto NO es un juguete. Mantenga este producto fuera del alcance de los niños. 2. Este producto ha sido diseñado únicamente para uso en interiores NO lo utilice en el exterior ni en entornos húmedos. 3. Evite la humedad y NO vierta agua ni otro líquidos sobre el producto. 4. NO instale el producto cerca de una fuente de calor. NO lo instale en lugares confinados, a menos que haya ventilación suficiente. 5. NO intente reparar este producto usted mismo.
Email: support@aqara.com Manufacturer: Lumi United Technology Co., Ltd. Address: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Courriel: support@aqara.com Fabricant: Lumi United Technology Co., Ltd. Adresse: 8th Floor, JinQi Wisdom Valley, No.1 Tangling Road, Liuxian Ave, Taoyuan Residential District, Nanshan District, Shenzhen, China. Correo electrónico: support@aqara.com Fabricante: Lumi United Technology Co., Ltd.