LS 600d Pro Product Manual English
Foreword Thank you for purchasing Aputure “Light Storm” LS 600d Pro. The Aputure LS 600d Pro is a perfect fixture with big power. It owns all features of previous series products,and further it will support the battery charging under the operation and another feature of it is that it can work on raining . IMPORTANT SAFETY INSTRUCTIONS When using this unit, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2.
8. Let the lighting fixture cool completely before storing. 9. To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids. 10. To reduce the risk of fire or electric shock, do not disassemble this fixture. Contact cs@aputure.com or take it to qualified service personnel when service or repair work is required. Incorrect reassembly may cause electric shock when the lighting fixture is in use. 11.
21. This product is certified by RoHS, CE, KC, PSE, and FCC. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunctions, although you may request such repairs on a chargeable basis. 22. The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.
Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a different circuit than the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help. RF Warning Statement: This device has been evaluated to meet general RF exposure requirements.This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Check list Please make sure all accessories listed below are completed before using.
Product Details 1. Lamp Head Bowens Mount Bowens Mount Release Latch Label LED Light Source Made in China UID 55° Hyper-Reflector 5-Pin Male XLR Receiver Cable Relief Hook Ratcheting Disk Brake Handle T-Handle / Baby Pin Mounting Screw Baby Pin Receiver/Mounting Column (5/8in. / 16mm) 2.
5-Pin Female XLR Power Output DMX OUT DMX IN Port Port Battery Input Neutrik® (DC) powerCON Power Input 3.
Installations 1. Attaching/detaching the protection cover Pull back the retaining pin, rotate the cover clockwise, then detach the cover. To reattach the cover, insert it into the Bowens mount and rotate counterclockwise. Notice: Always remove the protection cover prior to turning on the light. Always re-install the cover when packing it away. 2.
4. Instructions for the Quick-Release "Lightning Clamp" 1) Clamp the Lightning Clamp onto a light stand. 2) To attach the control box, rotate the release lever to unlock the quick-release baseplate, then mount the control box onto the Lightning Clamp (the release lever will automatically spring back). 3) To remove the control box, grasp it firmly, then unlock the quick-release plate by turning the release lever, and detach the control box. 1 2 1 2 Specifications Weight 670g / 1.48lbs Sizes (L*W*H) 10.
6. Powering up the controller 1) Powering by AC Neutrik® powerCON Male Connector PUSH AC 100V-240V 1 2 ~ ~ Neutrik® powerCON Female Locking Connector To disconnect the Neutrik® powerCon cable, pull back on the yellow release tab on the cable connector, and rotate the connector counterclockwise. 2) Powering by Batteries V-Mount Battery Anton Bauer Battery * Batteries Spec: Voltage 14.4~28.8V,but the capacity is higher 180Wh.
Operations 1. Press the power button to turn the light on and off Brightness Dimming Curve Wireless Mode Remaining Operating Time Battery Level/ AC Power Symbol Fixture Serial Number 2. Manual Control 1) Rotate the select button to adjust the intensity of the light from 0-100%. - + 2) Press the MENU button to enter the system menu interface, They are DMX Mode、Dimming curve、Fan Mode、Studio Mode、Control System、Language、Update、Effects.
2.1) DMX Mode Press the MENU button to enter the system menu, rotate the select knob to select DMX Mode, and press the select button again to enter DMX Mode. 2.2) Dimming curve Press the MENU button to enter the system menu, rotate the select knob to select Dimming Curve, and press the select button again to enter the dimming curve. rotate the select knob can choose your choice from exponential (Exp), logarithmic (Log), S-Curve, or linear dimming curves. 2.
2.4) Studio Mode Press the MENU button to enter the system menu, rotate the select knob to select Studio Mode, and press the select button again to enter the Studio Mode.Via press select button can choose "YES" or "NO". 2.5) Control System There are 4 control systems on it,namely Bluetooth、2.4G、Lumenradio and Art-Net. 2.5.1) Bluetooth (1) Under the control system, rotate the select knob to select on or off or Bluetooth Reset. Press the select button again to enter the Bluetooth Menu.
(2) After resetting the light's Bluetooth connection, your mobile phone or tablet will be able to connect to and control the light;If the Bluetooth Reset fails, a [Reset Failed] screen will pop-up, and the light will return to Bluetooth mode after 2 seconds. 2.5.2) 2.4G Control Under the control system, rotate the select knob to select 2.4G Control.Press the select button again to enter the 2.4G Control.You can adjust on or off、channel and group via rotate and press select button. 2.5.
2.5.4) Art-Net Under the control system, rotate the select knob to select Art-Net.Press the select button again to enter the Art-Net,You can see the information of Local IP、Remote IP、Gateway and MAC Address. 2.6) Language Press the MENU button to enter the system menu, rotate the select konb to select Language, and press the select button again to enter the Language menu. Use the knob to select from the available languages. Initial languages include "English" and "Chinese". 2.
2.8) Effects Press the MENU button to enter the system menu, rotate the select konb to select Effects, and press the select button again to enter the Effects toggled between Paparazzi, Fireworks, Faulty Bulb, Lightning, TV, Pulsing, Strobe, Explosion. a. Paparazzi Effect b. Fireworks Effect c. Faulty Bulb Effect d. Lightning Effect* * In lightning mode, short press the Effects button to single trigger the light effect. e. TV Effect f.
g. Strobe Effect h. Explosion Effect* * In explosion mode, short press the Effects button to single trigger the light effect. When in Lighting FX mode, short press the "select" button to enter Intensity Adjustment Mode. Then rotate the select wheel to adjust the intensity from 0% to 100% as displayed on the screen. When in Lighting FX menu, short press the "select" button to enter Frequency Adjustment Mode.
4) You can return effects interface whatever under any status via press Effects button. 5) You can also do an OTA wireless firmware update using the Sidus Link mobile app. 3. Remote Control You can control the LS 600d Pro from any channel or group configuration. * Light Storm lights have three channels (1/2/3) and four groups (A/B/C/D). * Only groups "C" or "D" can be used to control brightness and lighting effects, while groups "A" and "B" can only be used to control brightness.
3) FX Control Press the ( + / ) button to enter or exit lighting effect mode. Press the ( + / ) to toggle between different effects. Press the ( / ) buttons to adjust the output of the light. Press the ( / ) buttons to toggle the effect frequency. Enter or Exit Effect Mode a. Paparazzi Mode b. Fireworks Mode c. Faulty bulb Mode d. Lightning Mode e. TV Mode f. Pulsing Mode g. Strobe Mode h. Explosion Mode * The remote control can only be used to operate lighting effects if the lights are in groups C or D.
* The DMX interface schematic is shown in the pictures below: 3 4 2 5 3 4 1 5 PUSH Data 1+ (Primary Data Link) Data 2- (Optional Secondary Data Link) Data 1(Primary Data Link) Data 2+ (Optional Secondary Data Link) Signal Common Data 1+ (Primary Data Link) Data 1(Primary Data Link) Signal Common PUSH 2 1 Data 2- (Optional Secondary Data Link) Data 2+ (Optional Secondary Data Link) 2) Channel Selection In DMX mode, match the channel of your DMX controller with the light, and then adjust ac
2) DMX Chart DMX Channel Values / Functions (5 DMX Channels) Channel 20-39 2 Value Function 40-59 3 Dimmer 60-79 4 0-255 Intensity 0 to 100% 80-99 5 1 4 100-119 6 0-127 Manual Mode 120-139 7 128-255 FX Mode 140-159 8 FX Control 160-179 9 10 R Mode Selection 2 3 0-19 Paparazzi 180-199 20-39 Fireworks 200-219 40-59 Fault Bulb 220-255 60-79 Lightning Undefined IN Lightning mode 80-99 TV 0-9 Start Point 100-119 Pulsing 10-127 Single Trigger 120-139 Strobe 140
6. Using the Sidus Link APP You can download the Sidus Link app from the iOS App Store or Google Play Store for enhancing the functionality of the light. Please visit sidus.link/app/help for more details regarding how to use the app to control your Aputure lights. Get Sidus Link R App Sidus.link/app/help Specifications Operating Current 8A Power Supply 100V~240V 50Hz/60Hz Power Input ≤720W Power Output ≤600W CRI ≥96 TLCI ≥96 CQS ≥95 Radio Frequency 2.
Photometrics Distance 1m 3m 5m 22150(lux) 2600(lux) 1020(lux) 2058(fc) 242(fc) 95(fc) 98500(lux) 8500(lux) 3000(lux) 9150(fc) 790(fc) 280(fc) Bare Bulb Hyper-Reflector * This is an averaged result, the number might be slightly different on each light. Trademarks Bowens is a trademark registered by Bowens in China and other countries. Anton Bauer is a trademark registered by Anton Bauer in the US and other countries.
光 • 风暴 LS 600d Pro 使 用 者 指 南 中 文
前言 感谢您购买爱图仕“光·风暴”系列LED摄影灯—LS 600d Pro。 爱图仕LS 600d Pro 是一款大功率LED灯具。它拥有以往光风暴系列产品所 有的特性,并且在工作中支持电池充电,另外一个显著特点是雨天也能正 常工作。 重要的安全说明 使用此摄影灯时,应始终遵循基本的安全预防措施,包括: 1. 使用前阅读并理解所有说明。 2. 当儿童靠近设备或使用设备时,必须进行密切监督。在使用设备时,请 勿将设备置于无人看管状态。 3. 必须小心接触高温部件防止被烫伤。 4. 请勿操作电源线损坏的设备以及掉落或损坏的设备,直到合格的维修人 员检查过。 5. 请归置好电源线,防止被电源线绊倒或拉扯电源线导致设备断电,且电 源线不可接触灼热表面。 6. 如果需要延长线,应使用额定电流至少等于设备额定电流的延长线。额 定电流小于设备的电线可能过热。 7. 在清洁和维修之前以及不使用时,务必从电源插座上拔下电器插头。切 勿拉扯电线从插座拔出插头,应抓住插头并拉动来拔出。 8. 在存放前让设备完全冷却。存放时,请将电源线从设备上拔出,待冷却 后归置在手提包对应位置。 9.
10.为降低电击风险,请勿拆卸本产品,在需要维修时将其交给合格的维修 人员。不正确的重装可能会在随后使用设备时引起电击。 11.使用非制造商推荐的配件可能会引起火灾、电击或人身伤害。 12.请将本产品连接到接地插座。 13.使用前请将保护罩取下。 14.使用标准罩前将EVA内托取下。 15.本产品工作时,请勿遮挡散热孔,勿直视灯珠; 任何情况下勿触摸灯珠。 注 意 LED光源灯珠,切勿触碰 16.勿将本产品置于液体或其他易燃,易挥发溶剂附近,避免损坏产品。 17.请用软布、干布清洁本设备。 18.请勿在潮湿的环境下使用本设备,否则有短路或电击的危险。 19.需要维修时请联系授权的维修人员。本设备内有精密电子线路。未经许 可擅自拆卸导致故障不在本司保修范围内,但用户可以付费维修。 20.建议使用爱图仕原厂线缆。由于使用非爱图仕原厂附件导致本产品的任 何损坏,不在本司保修范围内,但用户可以付费维修。 21.本产品已通过RoHS, CE, KC, PSE和FCC认证,请参考相关国家标准使 用和操作。因使用操作不当而造成机器损坏,不在保修范围内,但用户 可以付费维修。 22.
FCC 符合声明: 此设备符合 FCC 规则第 15 部分中的规范。操作设备须符合以下两个条件: (1) 此设备不会导致有害干扰; (2) 此设备可承受任何外来干扰,包括可能导致非预期操作的干扰。 【警告】如果用户未经爱图仕明确许可而进行改动或改装,可能会丧失继续 操作该设备的权利。 【注】此设备经测试确定符合 B 类数码设备(依照 FCC 规则第 15 部分规范) 的限制。这些限制的设计旨在为居住场所安装条件下的有害干扰提供合理的 保护。此设备生成、使用并可以发射射频能量。如果未按照指示安装和使用 ,可能对无线电通信造成有害干扰。但是,在特定安装条件下,不保证这类 干扰不会发生。如果此设备确实对无线电或电视机接收信号造成有害干扰, 而这点可以通过关闭和打开设备来确定,那么建议用户尝试使用以下一种或 多种措施来消除干扰: 扩大设备与接收器之间的距离。 将设备连接到其他电路的插座中,而不是接收器所连接电路的插座。 咨询经销商或有经验的无线电/电视机技术人员以获得帮助。 FCC 辐射暴露声明 本设备符合FCC针对未受控制环境所制定的辐射暴露限制。 -3-
物品清单 使用本产品前,请检查包装内是否包含所有以下物品。如有缺失,请与经销商联系。 保护罩 (1 pc) 挂绳 (1 pc) 快装件 (1 pc) 摇控器 (1 pc) 灯体 (1 pc) 集线绑带 电源线 (1 pc) 控制盒 (1 pc) 55° 标准罩 (1 pc) 集线绑带 连接线 (1 pc) -4- 手提包 (1 pc)
产品视图 1. 灯体 顶杆手柄 保荣卡口 灯体贴纸 光源 Made in China UID 标准罩 接口公座 挂线柱 碟刹手柄 紧固手柄 灯体支撑柱 2.
控制盒输出接口 3.
安装 1. 保护罩的拆卸与安装 按照图示箭头方向拨顶杆手柄,同时将保护罩旋转拔出。反方向旋转则将保护罩装入。 * 使用时,务必将保护罩拔出,否则会烧掉。 不使用时,将保护罩装入以保护灯头。 2. 标准罩的安装与拆卸 按照图示箭头方向拨顶杆手柄,同时将标准罩旋转装入。反方向旋转则将标准罩拔出。 3.
4. 快装件使用说明 1)将快装件装到灯架或支架上; 2)打开快装件旋柄,将控制盒装进快装件(旋钮自动弹回); 3)打开快装件(必须抓住控制盒,不然会摔落),取下控制盒。 1 1 2 快装件规格 重量 670g / 1.48lbs 2 尺寸(长X宽X高) 10.35x8.74x12.5cm / 4.07x3.44x4.92in * 快装件能夹直径2-5cm / 0.79-1.97in的圆管或方管。 5.
6. 供电 1) 交流电供电 弹簧锁口 PUSH AC 100V-240V 1 2 ~ ~ 锁口槽 * 拆卸电源线时,请下拉电源线上的弹簧锁口按钮再拆卸,切勿硬拔。 2)电池供电 V-mount电池 * 电池规格:支持14.4~28.
操作 1. 接通电源,打开控制盒电源开关。 亮度指示 调光曲线显示 无线模式显示 剩余使用 时间显示 电池电量显示/ AC电源符号显示 序列号 2.
2.1) DMX模式 按MENU键进入菜单界面,旋转Select键并选择进入DMX模式。 2.2) 调光曲线 按MENU键进入菜单模式,旋转Select键并选择进入调光曲线,可以选择对应的 指数型、对数型、“S”型、线型曲线。 2.
2.4) 演播室模式 按MENU键进入菜单模式,旋转Select键选择演播厅模式,短按Select键进入演 播厅模式菜单,再旋转Select键选择”是“或”否“,短按Select键开启或关闭 演播厅模式。 2.5) 控制系统 有四种控制方式,它们分别是蓝牙、2.4G、Lumenradio和以太网。 2.5.
(2) 蓝牙重置成功后,可使用智能终端(手机或平板电脑)与灯进行配对连接,连 接 成功后,可以对灯进行相关控制;如果蓝牙重置不成功,将会弹出界面【 Reset Failed】,显示2秒后返回蓝牙界面。 2.5.2) 2.4G 控制 在控制界面,旋转Select键选择2.4G 模式,短按menu键进入2.4G子界面,通 过旋转、按压Select键可以调节2.4G的开关、频道以及群组的选择。 2.5.
2.5.4) 以太网 在控制界面,旋转Select键选择以太网,短按Select键进入以太网子界面,你可 以看到子网、IP地址、网关以及MAC地址。 2.6) 语言 按MENU键进入菜单模式,旋转Select键选择Language,短按Select键进入语言 菜单, 旋转Select键选择English或中文,再短按Select键确认选择。 2.
2.8) 光效 按MENU键进入菜单模式,旋转Select键选择光效,短按Select键进入光效子 界面,可以选择狗仔队模式、烟花模式、故障灯泡模式、闪电模式、电视模式 、脉搏模式、闪光灯模式、爆炸模式。 a. 狗仔队模式 b.烟花模式 c. 故障灯泡模式 d. 闪电模式 * 闪电模式下,需通过Effects按键触发光效,短按一次Effects按键触发一次光效。 e. 电视模式 f.
g. 闪光灯模式 h.
4) 可以通过按压Effects按键快速回到光效界面,无论处于什么状态下。 5) 固件升级可以通过Sidus Link app进行OTA在线升级更新。 3. 遥控器远程遥控 设置遥控频道为2,群组为B时,控制亮度可按如下操作: * 光•风暴控制盒和遥控器分1、2、3三个频道和A、B、C、D四个群组。 * A、B只能控制亮度,C、D控制亮度和光效的选择。 1) 遥控器设置和显示 2) 亮度调节 按遥控器B组的( 为0~100%。 按( / )键,选择频道2 “ ”指示灯亮,选择频道成功 )按键调节亮度,亮度以0.1%的变量均匀变化。亮度可调节范围 * DMX、DMX光效模式下,不可以进行遥控操作。 * 使用遥控器进行调节操作,必须切换至2.
(3) 光效控制 按遥控器的( 按遥控器的( + / / )按键进入或退出光效模式,按( )控制光效的亮度,按( / + / )切换光效模式。 )控制光效的频率。 进入或退出光效模式 a. 狗仔队模式 b.烟花模式 c. 故障灯泡模式 d. 闪电模式 e. 电视模式 f. 脉搏模式 g. 闪光灯模式 * 遥控器只能在灯处于C或D组时用于控制光效。 h. 爆炸模式 4.
*DMX接口定义如图所示: 4 5 数据正(+) 1 备用数据负(-) 数据负(-) 地 备用数据正(+) 数据正(+) 数据负(-) 地 2) 频道选择 2 3 4 5 PUSH PUSH 3 2 1 备用数据负(-) 备用数据正(+) DMX控制台通道数与控制盒DMX通道数保持一致时,可使用控制台进行亮度调节操作。 适用于单台或多台连接方式。 *光•风暴在DMX模式下,控制通道号出厂默认值为1。 *光•风暴在DMX模式下,LS 600d Pro可设置通道范围为1-512。 5.
2) DMX 实用表 DMX 频道数值-功能对应表 (5个频道) 频道 数值 1 0-255 20-39 2档 功能 40-59 3档 亮度调节 60-79 4档 亮度0-100% 4 模式选择 2 5档 6档 0-127 常规模式 120-139 7档 128-255 光效模式 140-159 8档 光效控制 160-179 9档 狗仔队 180-199 10档 20-39 烟花 200-219 R档 40-59 故障灯 220-255 备用 60-79 闪电 80-99 电视 0-19 3 80-99 100-119 闪电模式 0-9 起始点 100-119 脉搏 10-127 单次触发 120-139 闪光灯 128-255 循环模式 140-159 爆炸 160-255 备用 0-19 5 爆炸模式 0-9 起始点 频率控制 10-127 单次触发 1档 128-255 备用 * 进入DMX光效模式后,只能通过DMX控制台进行亮度、频率及光效调节。 * 当独立控制多
6. Sidus Link APP 的使用 您可以在App store和安卓市场搜索sidus link下载专业控制软件来控制爱图仕灯具, 更多详细使用方法请访问:sidus.link/app/help Get Sidus Link R App Sidus.link/app/help Specifications 工作电流 输入功率 CRI 输出功率 ≤720W TLCI ≥96 CQS 工作频率 ≥95 ≤600W ≥96 2.4GHz 1/2/3 色温 5600±200K 防水等级 IP54 电池要求 14.4V-15A ≥180Wh 26V-8.5A ≥180Wh 28.8V-7.5A ≥180Wh 散热方式 主动散热 APP控制方式 蓝牙 灯体 群组 100V~240V 50Hz/60Hz 频道 遥控距离 尺寸 工作电压 8A ≤100 米 30.78*24.36*15.01cm/12.12*9.59*5.91 in 控制盒(A-mount) 32.83*17.56*14.11cm/12.93*6.91*5.
亮度测试数据 距离 1m 3m 5m 裸光源 22150(lux) 2600(lux) 1020(lux) 2058(fc) 242(fc) 95(fc) 标准罩 98500(lux) 8500(lux) 3000(lux) 9150(fc) 790(fc) 280(fc) * 亮度数据为平均数据,不同灯的亮度会有微小差异。 商标声明 Bowens是保荣公司在中国或其他国家的商标及产品型号。 Anton bauer是安东保尔公司在美国或其他国家的商标及产品型号。 Neutrik®是 Neutrik® 公司在美国或其他国家的商标及产品型号。 -22-
Serial No. Item Name Purchase Date Buyer Name Buyer Phone Buyer Add Franchiser Seal Aputure Imaging Industries Co.,Ltd. Inspection: Qualified Add: F/3, Building 21, Longjun Industrial Estate, Heping West Road, Shenzhen, Guangdong Aputure Imaging Industries Co., Ltd. warrants the original consumer purchaser from defects in material and workmanship for a period of one (1) year after the date of purchase. For more details of warranty visit www.aputure.com Aputure Imaging Industries Co., Ltd.
产品编号 产品名称 购买日期 用户姓名 用户电话 用户地址 经销商印章 深 圳 市 爱 图 仕 影 像 器 材 有 限公司 检验:合格 地址: 深圳市龙华新区和平西路部九窝龙军工业区 保修条款(中文) 本公司对产品第一买主客户提供为期一年的质量保证期。 质保内 容和细节,请登陆我们的网站www.aputure.