Specification Sheet

ManualsBrandsApproved Vendor ManualsAnchors1/2X4 Hex nut Sleeve Anchor Zinc, Pkg of 25

Anchors

269

Hex Nut &

Washer style

Sleeve Anchor

LEEVE

NCHORS

EAD

FF-S-325, Group II,

Type 3, Class 3

LHFW

Drill

Diameter

Fixture

Clearance

Hole

Minimum

Embedment

Required Torque

to Set (Ft. Lbs.)

Tensile

Strength

(psi.)

Shear

Strength

(psi.)

Anchor Diam x

Length

Nut

Height

Head

Width

Washer

O.D.

Thread Size

of Stud

Ref Ref Ref

Carbon

Steel

Stainless

Steel

4000 psi. Concrete

Strength

5/16 x 1 1/2

7/32 7/16 5/8 5/16 3/8

1 3/8

1/4-20 8 -

- -

5/16 x 2 1/2 1 1/2 1750 2015

3/8 x 1 7/8

17/64 1/2 13/16 3/8 7/16 1 5/8 5/16-18 16 11 2700 32503/8 x 3

3/8 x 4

1/2 x 2 1/4

21/64 9/16 1 1/2 9/16

2 1/8

3/8-16 28 20

- -

1/2 x 3

2 1/4 5015 63721/2 x 4

1/2 x 6

5/8 x 2 1/4

7/16 3/4 1 3/8 5/8 11/16

2 1/8

1/2-13 60 42

5/8 x 3

2 3/4 6345 10,2555/8 x 4 1/4

5/8 x 6

3/4 x 2 1/2

35/64 15/16 1 3/4 3/4 15/16

2 1/8

5/8-11 90 60

- -

3/4 x 4

3 3/8 9135 12,800

3/4 x 5 3/4

Description

A device for giving stability to one part of a structure by making it fast to another consisting of (A) a threaded stud with a conical end

flared outward; (B) a hollow, cylindrical dilating sleeve assembled over the stud and positioned against the minor diameter of the cone; (C)

a washer and hex nut assembled at the end opposite the cone.

Applications/

Advantages

The anchor works by expanding against the material in which it is embedded. When the hex nut is tightened the conical end is pulled into

the dilating sleeve pushing it outward 360° around the anchor into the masonry. They are designed to be used in solid or hollow

masonry, including cinder block, brick, marble and concrete. One advantage of the sleeve anchor is that it can be removed after it's been

installed. Another is that the length of the sleeve induces less stress on the substrate than does a wedge anchor. It is well-suited for

permanently anchoring heavy equipment to concrete.

Material

Steel Stainless

Threaded Bolt: AISI 1010 - 1018 cold rolled steel

Sleeve: AISI 1008 cold rolled steel

Nut: Shall be made from a low carbon steel which conforms to the

following chemical composition requirements:

Carbon-

0.58%

maximum;

Phosphorus-

0.13% maximum;

Sulfur-

0.23% maximum

Washer: AISI 1008 - 1010 cold rolled steel

Threaded Bolt: 18-8 stainless steel

Sleeve: Type 304 stainless steel

Nut: Type 304 stainless steel

Washer: 18-8 stainless steel

Anchor Spacing

Anchors should be installed with a minimum of 10 anchor diameters between each other and a minimum of 5 diameters from the edge.

Tensile Strength

The suggested safe working load is one-fourth of the average proof test load shown in the above table.

Shear Strength

The suggested safe working load is one-fourth of the average proof test load shown in the above table.

Plating

Steel sleeve anchors are usually supplied plated zinc. Stainless sleeve anchors usually have no additional finish applied.

This page prints with a watermark