88.
1、出厂有配对，默认开机自动连接。 2、如果开机不连接，关闭扩音器，先开麦克风，长按麦克风M键，麦克风蓝灯开始快闪时， 打开扩音器主机，稍等一会就会连接。 3、如果多台一起使用，先关闭扩音器，先开麦克风，长按麦克风M键，麦克风蓝灯开始快闪时， 打开扩音器主机，连接后再短按 麦克风的M键切换频率，按一次，换一个频点。按多次， 频点持续变动。 4、复位操作 ：关闭无线麦，然后按住 无线麦音量 + 这个按键，不要松手，打开 无线麦电源开关， 灯会闪2下，就恢复出厂设置了 。 5、无线麦未连接是蓝灯慢闪，如果蓝灯快速闪烁，表示电量不足，请充电。 UHF无线麦克风 电量不足时，指示灯会闪烁。关闭麦克风插上充电时，指示灯亮红色， 充满指示灯熄灭。
2.
蓝牙功能介绍 蓝牙名称 :APORO ，按主机的M键 切换到蓝牙模式，显示屏显示BLUE并且闪烁，此时可以用 手机或者其他支持蓝牙的装备上搜索蓝牙设备，选择APORO点击配对连接。连接成功，显示屏 不再闪烁，显示PAUS，即可开始使用蓝牙播放了。 （本功能仅适用于部分带蓝牙的机型） Bluetooth function introduction The Bluetooth name is APORO. Press the M key of the host to switch to the Bluetooth mode. The display screen displays blue and flashes. At this time, you can search for Bluetooth devices on your mobile phone or other Bluetooth enabled devices, select APORO and click pairing connection.
US B 充电头要求为 V5 A1，最大不超过5V A2。 充电时，电池图标闪烁。充满电后，停止闪烁。建议充满后， 不要立即停止，继续充够4 小时，避免虚电。
8-12
合格证 检验员: A-001 QC
88.
1, the factor y has matching, default boot automatic connection. 2. If the boot is disconnected, turn off the amplifier, turn on the microphone first, press the microphone M key for a long time, when the microphone blue light starts flashing, turn on the amplifier, and connect later. 3.
2.4G When the power of 2.4G wireless microphone is insufficient, the indicator light will flash quickly. When charging, the indicator light is on red, and the full indicator light is off.
charging head is required to be 5V 1a, and the maximum is no more than 5V 2A. When charging, the batter y icon flashes. When fully charged, stop flashing. It is recommended not to stop immediately after full charge, and continue to charge for 4 hours to avoid vir tual power.
8-10
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
