User's Manual

ManualsBrandsApollo America ManualsElectronicsWireless Smoke Heat Alarm

ATTENTION: This manual should be read prior to use and retained for

further information.

GENERAL INFORMATION

The Wireless Smoke Heat Alarm is a 3xAAA battery powered wireless

detector intended for use with a compatible wireless alarm system. The

detector has a built-in wireless transmitter, which communicates with the

control panel. When smoke is detected, the alarm sounds a loud local alarm

and the built-in transmitter sends a signal to the control panel. The Wireless

Smoke Heat Alarm contains an integrated xed 41°F temperature freeze

sensor that will send a warning signal based on temperature detected. This

detector is designed to provide protection with 70-foot spacing capability.

The detector can send alarm, tamper and battery condition messages to

the system’s receiver. Refer to the wireless system’s instruction for the

maximum number of transmitters that can be supported.

CONTENTS OF BOX:

• Wireless Smoke Heat Alarm with base

51000-355 / 51000-357

Wireless Smoke Heat Alarm

Installation Guide

• Installation guide (APD0601)

• Pack of screws and anchors

• Labels or decals as appropriate

• 3 AAA PC2400 Duracell Procell batteries (1.5V 1100mAh) or 3 AAA

Energizer E92 batteries (1.5V 1100mAh)

The Wireless Smoke Heat Alarm contains a sounder which generates the

ANSI S3.41 temporal 3 pattern in an alarm condition. In alarm, a message

is also sent to the control panel and the detector’s ID is displayed at the

console. During an alarm condition, pressing the detector’s hush button

will silence the sounder (see table below). The mounting base installation

is simplied by the incorporation of features compatible for both drywall

fasteners (not supplied) and other methods.

Tricolored LED (red, yellow, green) and a sounder on the detector provide

local visual and audible indication of the detector’s status as listed in Table

During initial power-up the LED blinks alternately red, yellow then green. It

takes about 8 seconds for the detector to stabilize.

After power-up has completed and the detector is functioning normally, the

green LED blinks once every 12 seconds.

Detector Trouble: When the detector has a general fault, the yellow LED

blinks once every four seconds and there is a chirp every 48 seconds. After

12 hours the panel will display a loss of supervision message.

Summary of content (16 pages)

PAGE 1
51000-355 / 51000-357 Wireless Smoke Heat Alarm Installation Guide ATTENTION: This manual should be read prior to use and retained for further information. GENERAL INFORMATION The Wireless Smoke Heat Alarm is a 3xAAA battery powered wireless detector intended for use with a compatible wireless alarm system. The detector has a built-in wireless transmitter, which communicates with the control panel.
PAGE 2
Status LEDs Normal Green flash every 12 seconds Off Heat Alarm Red flash every 1 second ANSI S3.41 temporal 3 Smoke Alarm Red flash every 1 second ANSI S3.41 temporal 3 (press button to hush for 5-10 minutes) Heat Test Red flash every 1 second Smoke Test Red flash every 1 second Test Alarm Red flash every 1 second Detector Trouble Yellow flash every 4 seconds Freeze Warning Low Battery Detector Dirty Power-up Tamper 3 yellow flashes every 4 seconds ANSI S3.
PAGE 3
uring initial power-up the LED blinks alternately red, yellow sends then green. relative to the stairway so as to intercept smoke coming from a ﬁre in the the transmitter a low battery message to the control panel, which akes about 8 seconds for the detector to stabilize. before the smoke enters the stairway. displays the detector’s ID at low battery. In addition, the yellow LED ofbasement the detector will blink every 12 seconds.
PAGE 4
every 12 seconds to indicate normal operation. If the batteries are not room room the compartment. If the batteries are incorrectly inserted please remove - In or below a cupboard CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR correctly, thecorrectly detector will not operate and the batteries may be gently with installed a non-conductive tool and - Where air ﬂow would be HIGH reinsert. HUMIDITY MAY REDUCE BATTERY LIFE. the compartment.
PAGE 5
d ceilings 3 screws are at the elbow of the screw slots and secure. 2. Fit the detector inside the base by aligning it over the base as shown (detector’s alignment notch should be slightly offset from mounting base tamper release tab), then turn the detector in a clockwise direction until it clicks into place. MOUNTING THE DETECTOR 3.
PAGE 6
MAINTENANCE • Studies have shown that smoke and heat alarms may not awaken all sleeping individuals, and that it is the responsibility of individuals in the household that are capable of assisting others to provide assistance to those who may not be awakened by the alarm sound or those who may be incapable of safely evacuating the area unassisted. TEST ONCE A WEEK. WARNING! USE ONLY BATTERIES SPECIFIED. USE OF DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE SMOKE ALARM.
PAGE 7
IF THE ALARM SOUNDS a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 8
51000-355 / 51000-357 Détecteur de chaleur et de fumée sans fil Guide d'installation This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.) (National Fire Alarm Code® and NFPA 72® are registered trademarks of the National Fire Protection Association, Inc., Quincy, MA 02269.
PAGE 9
État DEL Normal Détecteur de chaleur Épreuve de résistance à la chaleur Détecteur de fumée Clignote en vert toutes les 12 secondes Clignote en rouge chaque seconde Clignote en rouge chaque seconde Clignote en rouge chaque seconde Test de fumée Clignote en rouge chaque seconde Tester le détecteur Alarme de gel Clignote en rouge chaque seconde Clignote en jaune 3 fois toutes les 4 secondes Défaut du détecteur Clignote en jaune toutes les 4 secondes Piles faibles Clignote en jaune toutes les 12 seconde
PAGE 10
Normal Heat Alarm second 1. Remove the detector from its mounting base by twisting the detector counterclockwise. Remove and dispose of the batteries according to your local regulations. Off Red ﬂash every 1 2. To ensure proper power-down sequence, wait a minimum of 20 seconds secondremplacées. Appuyez sur le bouton silence pour arrêter les bips sonores pendant 12 heures, s’il n’existe aucun autre défaut. Remplacez les piles dès que les bips piles soient before installing new batteries.
PAGE 11
6. Test the detector (as described later). 6. Test the detector (as described later). Entrée dans cette zone the ceiling surface, and begins to bank down from the ceiling. The corner where the ceiling and wall meet is an air space into which the smoke could CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR OR CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES HIGH HUMIDITY MAYMAY REDUCE BATTERY LIFE.LIFE. have difﬁculty penetrating.
PAGE 12
damaged. If the detector does not power-up, check for correct batteries installation and for a fully charged batteries 6. Test the detector (as described later). Cave Fig 4. Un détecteur installé à chaque étage Endroits déconseillés pour l’installation d’un détecteur : CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH HUMIDITY MAY REDUCE BATTERY LIFE.
PAGE 13
2. Appuyez et maintenez le bouton de test pendant au moins 5 secondes. Le panneau d’alarme se déclenche puis le détecteur se met en alerte. La sonde émet la séquence temporelle 3 et la DEL rouge clignote. La console du panneau d’alarme doit en principe afficher le nom du détecteur ayant déclenché l’alarme. est capable de protéger environ la moitié des occupants des incendies potentiellement mortels.
PAGE 14
• • • • • • • • • • Dimensions : Ø 125 mm x hauteur 63 mm (Ø 5 po x hauteur 2,5 po) Poids (piles incluses) : 243 g oz (8,57) Couleur : blanc Capacité du rayon : 70 pi Signal sonore (ANSI Temporel 3) : 85 dBA min.
PAGE 15
le parcours du signal a été récemment vérifié au cours d’un test hebdomadaire. Un blocage peut se produire si un objet métallique a été déplacé dans le parcours du signal du capteur. • Réorientez ou déplacez l’antenne de réception. • Augmentez la distance qui sépare l’équipement du récepteur • Branchez l’équipement à une prise située sur un circuit différent de celui auquel le récepteur est connecté.
PAGE 16
Apollo America 25 Corporate Drive Auburn Hills, MI 48326 248-332-3900 Phone 888-332-2241 Tech Support www.apollo-fire.