User's Manual

所有材质符合RoHS/REACH/WEEE
印刷+模切+折叠
四色印刷
深圳市爱培科技术股份有限公司
SC20050028-IP206机器说明书（英文版）
版本号码：V1.02
设计日期：2021-08-30
责任设计师：姚佳欢
尺寸：80*80mm
材质：整本80g双胶纸
工艺：正反印刷，骑马订
公差：公差：±1mm
变更履历：
1. 增加内容
2.
3.
爱培科产品包装图纸
19206
User Manual
Packing List
Please make sure unit and accessories well after box open .
Camera x1
Screw bag x1
Position paper x1
User manual x1
USB cable x1 AC adaptor x1
ID instruction
Lens
Mic
Micro SD
LED indicator
Speaker DC
Setting
3. Installation on the wall ( Optional)
Cement Wall
Wood Wall
-Before installation, please confirm that the camera has
been added into the APP;
-Removing the positioning paper and paste it to the installation
location;
-Aligning the wall of the positioning paper part and pushing the
screw directly; The cement wall needs to be drilled, pushing in
the anchoring screw firstly, and then pushing in the screw;
-Aligning the guide rails on the back of the camera with the
screws, and pushing the camera back to fix the camera;
Installation instruction
1.Before the installation. , make sure the camera has been
added onto app.
2.Pls try to find a place which has good view to place the
camera.
Normal Questions
Q: How to record a video?
A: The camera supports two kinds of storage ways, local
storage and cloud storage (Need purchase).
Local Storage: Put the camera recorded video on the
Micro SD card Cloud Storage: Put the camera recorded
video on the cloud, according to the length of storage
recording, it can support the two types of loop recording
the recent seven days and thirty days. Support checking
online, downloading the history video.
Q: Why the camera can’t connect with the WI-FI network?
A: Currently the camera supports 22.4G WI-FI which based
on the 802.11b/g/n protocol, not support the 5G Wi-Fi.
Please make sure the router WI-iFi signal is under the
coverage.
Q: The camera offline strangely, how to check?
A: Check whether the power and network is normal
Restart the device via the re-plugging
Re-matching the camera
Check whether the network bandwidth is above 4Mbps
8 9
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
shall be installed and operated with minimum distance 20cm
between the radiator & body.
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
RF Exposure Warning Statements:
Quick configuration
1.Connect the mobile phone to the WI-FI network, scan the QR
code below on WeChat, follow the WeChat official account,
download the Tuya smart APP and complete the installation.
2.Open the Tuya smart APP and click "Register". If you have an
account, you can log in directly.
3.After logging in, click the "Add Device" button on the
homepage interface, or the "+" button in the upper right
corner to complete the device addition according to the voice
prompts.
Power supply connection
Connect the power interface and power socket on the back of
the camera with the data cable. When the indicator light of the
camera is on, the power is switched on.
Indicator light
- Always red light: The camera has been connected to the power
supply and is not bound to the account“和目”；
-Red light flashing: After long press the setting key, the camera will
enter the scanning state;
- Always green light: The camera is successfully bound and the
connection network is normal；After long press the setting
button, the green light will be long, indicating hardware failure；
-Green light flashing: The camera is connected to the Internet.