888.880.8992 OWNER’S GUIDE Aperion Intimus 4T Summit Wireless 5.1 Home Theater System powered by: www.summitwireless.com AperionAudio, Audio,Inc. Inc Aperion 18151SW SWBoones BoonesFerry FerryRoad Road 18151 Portland,OR OR97224 97213USA USA Portland, toll-free(USA): (USA):888.880.8992 888.880.8992 toll-free fax:503.598.8831 503.598.8831 fax: email:customerservice@aperionaudio.com customerservice@aperionaudio.com email: web: www. www.aperionaudio.com web: aperionaudio.
Congratulations! Thank you for purchasing the Intimus 4T Summit Wireless Home Theater System. You are one of the first in the world to experience the high quality audio and easy setup of truly wireless home theater! While we did our absolute best to eliminate every possible wire, the realities of power had to be considered.
Owner’s Guide Notes Contents ______________________________________________________________________________ 1. Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Home Theater One Wireless Transmitter 12. Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12.1 ASSOCIATE Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12.2 Frequency Agility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12.3 Speaker Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 12.4 MyZone™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Home Theater One Wireless Transmitter Owner’s Guide 16. Warranty 1. Package Contents Aperion Audio provides a transferable ten (10) year limited warranty on our speaker cabinets and drivers; a transferable one (1) year limited warranty on our electronics in subwoofers, powered speakers and wireless transmitters; and a non-transferable lifetime limited warranty on our cables. Make sure you have all the items listed below. Inspect each piece to make sure nothing was damaged during shipping.
Home Theater One Wireless Transmitter Home Theater One Wireless Transmitter 2. Home Theater One Wireless Transmitter Features 2.
Home Theater One Wireless Transmitter 3.2 Panel Connections 14.Rear Regulatory Statement The United States Federal Communication Commission has established certain rules governing the use of electronic equipment. 14.1 FCC Certification This device complies with Part 15 of the FCC Rules. Owner’s Guide 3.
Owner’s Guide Home Theater One Wireless Transmitter Owner’s Guide 13. Specifications 13. Specifications • Three HDMI 1.4 inputs 3.2 Rear Panel Connections • One ThreeHDMI HDMI1.4 1.4output inputs • Coaxial digital One HDMI 1.4input output • Optical Coaxial digital input • Two analog stereo inputs Optical digital input • Dolby TrueHD Two analog stereo inputs • DTS Audio DolbyMaster TrueHD • Audio sampling: 32 KHz, 44.1 KHz, 48 KHz, and 96 KHz DTS Master Audio • Audio sampling: 32 KHz, 44.
Home Theater One Wireless Transmitter 12. Glossary Owner’s Guide 4. Remote Control 12.1 ASSOCIATE Button The ASSOCIATE Button puts the speaker in associate mode so the Home Theater One Wireless Transmitter can determine what speaker should be the anchor speaker. This operates much like the Associate button on a wireless keyboard or mouse on computer systems. Only use the ASSOCIATE button on one speaker in a room during initial setup.
Home Theater One Wireless Transmitter 5. Wireless Speaker Back Panel Owner’s Guide 8. Pressing MyZone keeps showing “Please Retry.” The following shows a typical Aperion Wireless speaker back panel. The speakers must be plugged-in and powered on for the system to work. When the Home Theater One Wireless Transmitter is powered off, the speakers go into a low-power standby state and should remain plugged in at all times.
Home Theater One Wireless Transmitter 3. Remove the speaker grill from the center speaker. It can be reinstalled after the system has been successfully set up. 4. Use the Refresh Map menu item (see the section “Refresh Map” for more details). 5. The map shows my proper speaker setup, but the input signal display shows "No Sig" and I can't hear anything. When the display shows "No Sig", that means it is not receiving any audio data from your player. Check the following: Owner’s Guide 6.
Home Theater One Wireless Transmitter 7. Speaker Placement Owner’s Guide 3. The display Map shows a different number of speakers than I have. To get the best audio reproduction from surround-sound encoded material, Dolby and DTS recommend you place the speakers in a configuration as close as possible to the following diagram. Make sure each speaker can directly “see” the other speakers in the room and that they are pointed toward the center of the room.
Home Theater One Wireless Transmitter Owner’s Guide Refresh Map If you’ve moved speakers to new positions, or if you want to add additional speakers, select this option. Any audio that is playing stops, and the system restarts. After restart, the system identifies new speakers, if any, and remaps them. Note: This menu item is the same under the main menu and the advanced menu. The function is the same.
Home Theater One Wireless Transmitter Owner’s Guide Front Speaker Placement OK Current Speaker OK Current Level Setting 2. Pressing LEFT ARROW or RIGHT ARROW on the remote selects different speakers. Pressing UP or DOWN adjusts the level of the currently selected speaker in 1 dB steps. Note: The system works best with the left and right speakers either even with or in front of the center channel speaker. 3. When finished, press EXIT to return to the main display. 10.6.
Home Theater One Wireless Transmitter Owner’s Guide 8. Speaker Placement Tips and Hints 10.6.1 Speaker Volume Settings Note: Enter MENU to find this option. 1. Where should I place the front speakers? The first step in optimizing the speaker system is to run MyZone (refer to "MyZone Optimization" for details). For almost all situations, this is all that is needed. MyZone automatically adjusts speaker volume based on your location and the speaker's location.
Home Theater One Wireless Transmitter 9. Connections Owner’s Guide 10.4 Changing Volume Connect your Home Theater sources to the Home Theater One Wireless Transmitter inputs that fit them best. See the examples on the following pages. Place Antennae in Vertical Position To change the current volume, use the VOL buttons on the remote control. You’ll see the status update in the volume section of the front panel: VOL+ — Pressing increases the volume. Pressing and holding quickly increases the volume.
Home Theater One Wireless Transmitter 10. Using the System Owner’s Guide 9.1 Example 1: HDMI These sections explain how to use the features of the Home Theater One Wireless Transmitter. 10.1 Powering On and Off After you're finished with the initial setup (see section 6 “Installation and Setup” for details), you simply need to press the POWER button on the remote control to turn the Home Theater One Wireless Transmitter on and off.
Home Theater One Wireless Transmitter 9.2 Example 2: Non-HDMI Video Source Owner’s Guide 9.