User Guide

ManualsBrandsAPC ManualsComputer Accessories & PeripheralsAPC Back-UPS Pro 1000VA UPS Battery Backup & Surge Protector (BR1000G)

Installation and Operation

Back-UPS

™

Pro BR1000G

Connect the Battery

Install PowerChute

™

Personal Edition Software

PowerChute Personal Edition software provides automatic file saving and shutdown of your computer

in the event of a power failure. Use the cable supplied with the Back-UPS to connect the data port on

the Back-UPS to the USB port on your computer. Place the CD into your computer, and follow the on-

screen instructions.

Inventory Safety and General Information

Inspect the package contents upon receipt. Notify

the carrier and dealer if there is any damage.

Read the Safety Guide supplied with this unit before

installing the UPS.

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there

is excessive dust or humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for

proper ventilation.

• The battery typically lasts for three to five years. Environmental factors impact

battery life. Elevated ambient temperatures, poor quality AC power, and

frequent short duration discharges will shorten battery life

• Connect the UPS power cable directly to a wall outlet. Do not use surge

protectors or extension cords.





bu001b

Us er Doc ument atio n

bu055a

bu057a

bu059a

bu058a

bu060a

Us er D o cu me n ta t i on

Summary of content (8 pages)

PAGE 1
Installation and Operation Back-UPS™ Pro BR1000G Inventory Safety and General Information Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage. bu001b User Documentation Read the Safety Guide supplied with this unit before installing the UPS. • This UPS is intended for indoor use only. • Do not operate this UPS in direct sunlight, in contact with fluids, or where there is excessive dust or humidity. • Be sure the air vents on the UPS are not blocked.
PAGE 2
Connect the Equipment Battery Backup and Surge Protected outlets When the Back-UPS is receiving input power, the Battery Backup with Surge Protection outlets will supply power to connected equipment. During a power outage or other AC problems, the Battery Backup outlets receive power for a limited time from the Back-UPS. Connect equipment such as printers, fax machines, scanners, or other peripherals that do not need battery backup power to the Surge Protection Only outlets.
PAGE 3
Operation Power Saving Function To conserve electricity, configure the Back-UPS to recognize a Master device, such as a desktop computer or an A/V receiver, and Controlled peripheral devices, such as a printer, speakers, or a scanner. When the Master device goes into Sleep or Standby mode, or is switched OFF, the Controlled device(s) will be switched off as well, saving electricity.
PAGE 4
Front Panel Buttons and Display Interface Use the three buttons on the front panel of the Back-UPS and the display interface to configure the Back-UPS.
PAGE 5
Warnings and System Faults Audible Warnings Four Beeps Every 30 Seconds Back-UPS is running on battery. You should consider saving any work in progress. Continuous Beeping Low battery condition and battery run-time is very low. Promptly save any work in progress, exit all open applications, and shut down the operating system. Continuous tone Battery Backup outputs are overloaded. Chirps every 2 Seconds with the Load Capacity Bar flashing Battery is disconnected.
PAGE 6
Function Button Quick Reference Timing (seconds) UPS Status Power On 0.2 Off Press POWER to start receiving input AC power. If AC input power is not available, the Back-UPS will run on battery power. Power Off 2 On The Back-UPS is not receiving input AC power, but is providing surge protection. 0.2 On Verify the status or condition of the Back-UPS. The LCD will illuminate for 60 seconds. 2 On The LCD will illuminate and the Back-UPS will beep to confirm the Full-Time mode.
PAGE 7
Troubleshooting Problem Back-UPS will not switch on. Possible Cause Corrective Action The Back-UPS is not connected to AC power. Ensure that the Back-UPS is securely connected to an AC outlet. The circuit breaker has been tripped. Disconnect non-essential equipment from the BackUPS. Reset the circuit breaker. Re-connect equipment one item at a time. If the circuit breaker is tripped again, disconnect the device that caused the trip. The internal battery is not connected. Connect the battery.
PAGE 8
Specifications t VA 1000 VA Maximum Load 600 W Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the manual to eliminate common problems. Nominal Input Voltage 120 V 2. If the problem persists, contact Schneider Electric IT (SEIT) Online Input Voltage Range 88 - 141 V Customer Support through the APC by Schneider Electric Web site, www.apc.com. (94-107) +11.2% Automatic Voltage Regulation a.