Full Product Manual

ManualsBrandsANZZI ManualsBathKros Series 2-Handle Freestanding Claw Foot Tub Faucet with Hand Shower in Polished Chrome

V2.1

ITEM:FS-AZ0047**

03/03/2023

ANZZI Freestanding Tub Filler

V2.1-This version supersedes all previous versions as of 03/03/2023

Summary of content (9 pages)

PAGE 1
ITEM:FS-AZ0047** ANZZI Freestanding Tub Filler V2.1 03/03/2023 R V2.
PAGE 2
PAGE 3
PRODUCT SIZE CHART 41 1043mm 40.9 1040mm 3/8 COMPRESSION TOOLS AND MATERIALS Wrench Marker Pen Drill 25/64"(10mm) Drill Bit 2"Hole Saw PG.
PAGE 4
COMPONENT [01] [02] [03] [25] [04] [05] [06] [19] [20] [21] [10] [07] [09] [08] [09] [10] [11] [23] [12] [13] [14] [15] [16] [22] [24] Part [01] [02] [03] [04] [05] [06] [07] [08] [09] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] Description Spout Gasket Flow Regulator Faucet Check Valve Diverter Retainer(Diverter) Handle(Diverter) Screw Cap Post Hand Shower Check Valve Gasket Escutcheon Screw Anchor Expansion Screw Cartridge Retainer Cover Handle Inlet Hose Sh
PAGE 5
INSTALLATION 2 1 [11] [11] [15] [15] [16] STEP 1: Slide the Escutcheon [15] onto the Post [11]. [17] STEP 2: Install the Anchor [17] to the Post [11] and hand tighten it. Secure the Screw [16] on side by Allen Key. PG.
PAGE 6
INSTALLATION 3 4 [04] [04] [11] [23] [15] Hot Water [17] Cold Water STEP 3: Install the Inlet Hoses [23] to the Faucet [04] and secure. Note: Makes sure to connect the Inlet Hose [23] labeled “Hot” to the Faucet [04] inlet marked “H” and the Inlet Hose [23] labeled “Cold” to the Faucet [04] inlet marked “C”. STEP 4: Slide the Inlet Hose [23] through the Post [11] and the Anchor [17]. Install the Post [11] to the Faucet [04] and tighten it.
PAGE 7
INSTALLATION [04] [11] check for leaks here STEP 7: a.Unscrew the Post [11]. b.Turn on hot and cold water supplies and check connections at arrows for leak s. c. Connect the Post [11] to the Faucet [04] again. Tighten the Post [11] to secure. . 8 STEP 8: . [15] Nut a-1. Install the Expansion Screws [18] for concrete floor. Position the Anchor [17] of the faucet through the Expansion Screw [18], slide the Washers onto the Anchor [17] and secure it by tighten the Nuts. a-2.
PAGE 8
INSTALLATION 9 [12] 10 [08] [04] [22] [24] STEP 9: Install and secure the Hand Shower [12] and Shower Hose [24] to the faucet as the figure shows. Note: Make sure there are washers between the connections. STEP 10: Open the Handle [22], then turn the Handle (Diverter) [08] to check the flow of spout and hand shower. Check connections at arrows for leaks. Retighten if necessary, but do not over tighten. CLEANING & MAINTENANCE 1.
PAGE 9