ANYWAVE Version 1.1 COMMUNICATION TECHNOLOGIES June 6, 2017 MHPTV User Manual October 18, 2019 - Version 3.
MHPTV TX User Manual Copyright Notice Copyright © Anywave Communication Technologies, Inc. 2019, All rights reserved. No part of this publication may be reproduced, translated, transcribed, stored in a retrieval system, or transmitted into any form or by any means, without the express written permission of Anywave Communication Technologies, Inc. FCC Compliance Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
MHPTV TX User Manual PLEASE READ THIS MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO OPERATE THE EQUIPMENT. CONTACT ANYWAVE WITH ANY QUESTIONS OR CONCERNS YOU MAY HAVE. Unpacking Carefully unpack the equipment and perform a visual inspection to determine if any apparent damage has occurred during shipment. Please notify the delivery carrier and Anywave immediately if shipment damage has occurred. Retain all original shipping materials.
MHPTV TX User Manual WARNING THE VOLTAGES, CURRENTS, AND RF ENERGY IN THIS EQUIPMENT ARE DANGEROUS. PERSONNEL MUST AT ALL TIMES OBSERVE ALL SAFETY WARNINGS, INSTRUCTIONS, AND REGULATIONS. IN THE CASE OF EMERGENCY, ENSURE THAT ALL POWER HAS BEEN DISCONNECTED. ALWAYS DISCONNECT POWER BEFORE REMOVING COVERS, ENCLOSURES, OR SHIELDS. DO NOT PERFORM SERVICE ON THE EQUIPMENT WHEN ALONE OR FATIGUED. KNOW YOUR EQUIPMENT AND DO NOT TAKE RISKS.
MHPTV TX User Manual Contents 1. Introduction ...................................................................................7 1.1 TX System Configuration ........................................................................................ 8 1.2 TX Overview ........................................................................................................... 9 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 1.2.8 2. System Block Diagram ........................................................
MHPTV TX User Manual 5. 6. 4.6 OPTITUNE (Available in CTL-M) ........................................................................ 98 4.7 VOLTAGE ADJUSTMENTS (Available in CTL-M) .......................................... 103 Local (Touch Screen) User Interface.......................................106 5.1 HOME SCREEN ................................................................................................. 106 5.2 A/B EXCITER ICON SCREEN .................................................
MHPTV TX User Manual 1. Introduction This User Manual contains operational instructions for the Anywave MHPTV Transmitter fitted with 1, 2, 3, 4, 5, 6, or 8 PA drawers, delivering output powers as shown below (after the BPF). Please note that trained and qualified personnel are required to operate, install, maintain, and service this transmission equipment. 1100W ATSC 1000W COFDM 2200W ATSC 2000W COFDM 3300W ATSC 3000W COFDM 6600W ATSC 6000W COFDM MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.1 TX System Configuration The operation of the MHPTV Transmitter is essentially the same independent of the Exciter modulation standard implemented - DTV (ATSC, ATSC 3.0, DVBT/T2, ISDBT, DTMB, etc. The differences are in the Exciter setup and configuration (please reference your specific Exciter user manual for details). MHPTV Transmitters are fitted with Doherty (Hi-Efficiency) PAs.
MHPTV TX User Manual 1.2 TX Overview 1.2.1 System Block Diagram A hi-level System Block Diagram of the MHPTV TX is shown below. The MHPTV system essentially consists of an Exciter, a Controller (with built-in preamp), 1,2,3,4,5,6, or 8 Power Amplifiers with corresponding input Splitter and output Combiner, and a Band Pass (mask) Filter. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.2 1-PA TX The Anywave 1-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below. The main subsystems (as seen from the front) include one or two Exciter(s), one Controller (with a touchscreen LCD, and built-in preamp), one PA-8D-C-FA power amplifiers (8-power transistors per PA), and one AC Mains Breaker. Exciter Controller PA AC Mains Breaker MHPTV-USR-DOC-V3.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, one 2-port directional coupler and one Low Pass Filter (installed in the cabinet). LPF Exciter Coupler Controller PA AC Distribution MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 1-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 1-PA MHPTV system Cabinet dimensions are shown below. Please note: if the BPF (not shown) is mounted on top of the TX cabinet – then the additional height of the BPF must be considered in the overall system height. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.3 2-PA TX The Anywave 2-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include an AC Distribution System, one 2-way Splitter and Combiner, one 2port Directional Coupler, and one Reject Load. Splitter Exciter Coupler Controller PA 1 PA 2 Combiner AC Reject Load MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 2-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 2-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.4 3-PA TX The Anywave 3-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, one 3-way Splitter and Combiner, one 2port Directional coupler, and one Reject Load. Coupler Exciter Controller Combiner PA 3 Splitter PA 2 PA 1 Reject Load MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 3-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 3-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.5 4-PA TX The Anywave 4-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, one Combiner, one 2-port Directional coupler, and one Reject Load. Coupler Exciter Controller Splitter PA 4 Combiner PA 3 PA 2 Reject Load PA 1 AC Distribution MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 4-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 4-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.6 5-PA TX The Anywave 5-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, one Combiner, one 2-port Directional coupler, and one Reject Load. PA 1 PA 2 PA 3 PA 4 Combiner PA 5 Reject Load AC Distribution MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 5-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 5-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.7 6-PA TX The Anywave 6-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual 10” Touch Screen for Performance Monitoring (with ANY1022 option) MHPTV-USR-DOC-V3.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, one Combiner, one 2-port Directional coupler, one Low Pass Filter, and one Reject Load. Coupler Exciter Controller LPF PA 1 PA 2 Combiner PA 3 PA 4 PA 5 PA 6 Reject Load AC Distribution MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 6-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 6-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.2.8 8-PA TX The Anywave 8-PA MHPTV Transmitter comes in single and dual exciter configurations. Photos of a single exciter system are shown below.
MHPTV TX User Manual From the rear view of the TX cabinet, several other main components can be seen which include one AC Distribution System, Combiners, one 2-port Directional coupler, one Low Pass Filter and one Reject Load. Coupler LPF Exciter Controller PA 1 PA 2 Combiner PA 3 PA 4 PA 5 PA 6 PA 7 PA 8 Reject Load AC Distribution MHPTV-USR-DOC-V3.
MHPTV TX User Manual The diagram below shows the overall system interconnect between the various modules in the 8-PA MHPTV system. MHPTV-USR-DOC-V3.
MHPTV TX User Manual The 8-PA MHPTV system Cabinet dimensions are shown below. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1.3 TX Specifications RF Output Connector: Frequency: Rated Power (after BPF): Level Stability: MER: Amplitude Flatness: Shoulder Level: Return Loss: Environment Operation Temperature: Operation Humidity: Atmospheric Pressure: Power Supply Voltage: Frequency: 1 5/8” (1, 2, 3, 4 or 5 PA), 3 1/8” (6 or 8 PA), 50 Ω 470~610 MHz, in steps of 1 Hz 1.1, 2.2, 3.3, 4.4, 5.5, 6.6, 8.8 kW (rms) (ATSC) < ±0.2 dB > 35 dB < ±0.
MHPTV TX User Manual 1.4 AC Power Requirements Please review the safety WARNINGS on page 4 of this manual before proceeding with any electrical work. A licensed Electrician is required to properly and safely connect the AC mains power cable from your station's electrical panel to the terminal block located inside the TX AC Mains Distribution compartment in compliance with local electrical and building codes.
MHPTV TX User Manual The MHPTV TX AC distribution compartment may be wired for 240VAC singlephase (3-wire, L1, L2, GND) or 208VAC three-phase (4-wire, L1, L2, L3, GND) power to be sourced from a proper breaker sized according to the charts below. Also, please note the recommended cable gauge to make the connection between the TX AC Mains Distribution terminal block and the circuit breaker installed in the facility electrical panel.
MHPTV TX User Manual MHPTV – (Granite) Doherty AC Power Requirements MHPTV- (Granite) Doherty (888E) -AC Power Requirements, Dimensions, and Weights 240VAC 208VAC Net Weight (lbs.) After BPF(W) Single-phase (L1, L2, GND) Three-phase (L1, L2, L3, GND) Dimensions (mm) Delta 3110W consumption 3110W consumption 20A, 2pole breaker, gauge 12 1100(ATSC), 1PA 15A, 3pole breaker, gauge 14 wire Weight: 400 lbs. 1358H x 850D x 725W (mm) wire 2200(ATSC), 2PA 3300(ATSC), 3PA 13.0A/phase-current draw 8.
MHPTV TX User Manual 1-PA 240VAC, Single-Phase AC Distribution Wiring Properly connect the three wires to the terminal block as shown in the above diagram, taking care to notice which terminal is connected to the chassis Ground in your system. Be sure to connect the GND terminal properly and other two connections as L1 and L2. MHPTV-USR-DOC-V3.
MHPTV TX User Manual 1-PA 208VAC, Three-Phase AC Distribution Wiring Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Schneider iC65N D 50A Controller Load Amp1 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 F16-371/24VD A1 SIEMENS 3TF45 22-1X UK35 24v/50w AC Gnd Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd KDY-204P PE Gnd Properly connect the four wires to the terminal block as shown in the above diagram, taking care to notice which termin
MHPTV TX User Manual 2-PA 240VAC, Single-Phase AC Distribution Wiring Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Controller Schneider iC65N D 50A Load Amp1 Amp2 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 F16-371/24VD A1 SIEMENS 3TF45 22-1X Gnd UK35 24v/50w AC Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC220V L N Gnd 1 2 3 4 L1 L2 Gnd Gnd UK50 KDY-202P PE Gnd Properly connect the three wires to the terminal block as shown in the above diagram, taking care to notice which te
MHPTV TX User Manual 2-PA 208VAC, Three-Phase AC Distribution Wiring Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Controller Schneider iC65N D 50A Load Amp1 Amp2 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Gnd UK35 F16-371/24VD A1 SIEMENS 3TF45 22-1X 24v/50w AC Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd KDY-204P PE Gnd Properly connect the four wires to the terminal block as shown in the above diagram, taking care to notice w
MHPTV TX User Manual 3-PA 208VAC, Three-Phase AC Distribution Wiring Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Controller Load Schneider iC65N D 50A Amp1 Amp2 Amp3 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 F16-371/24VD A1 SIEMENS 3TF45 22-1X Gnd UK35 24v/50w AC Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd KDY-204P PE Gnd Properly connect the four wires to the terminal block as shown in the above diagram, taking care
MHPTV TX User Manual 4-PA 208VAC, Three-Phase AC Distribution Wiring Set-top fan Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Exciter two Controller Load Schneider iC65N 4D 63A Amp1 Amp2 Amp3 Amp4 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 F16-371/24VD A1 SIEMENS 3RT50461BB40 Gnd UK35 24v/50w AC Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd KDY-204P PE Gnd Properly connect the four wires to the terminal bl
MHPTV TX User Manual 5-PA 208VAC, Three-Phase AC Distribution Wiring Set-top fan Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Exciter two Controller Load Amp1 Amp2 Amp3 Amp4 Amp5 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 F16-371/24VD A1 SIEMENS 3RT50461BB40 Schneider C120H C100 UK35 24v/50w AC Gnd Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd KDY-20-4P 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd PE Gnd Properly connect the four wires to the term
MHPTV TX User Manual 6-PA 208VAC, Three-Phase AC Distribution Wiring Set-top fan Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Exciter two Controller Load Amp1 Amp2 Amp3 Amp4 Amp5 Amp6 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 F16-371/24VD A1 SIEMENS 3RT50461BB40 24v/50w AC Schneider C120H C100 UK35 Gnd Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd KDY-20-4P 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd PE Gnd Properly connect the four wires
MHPTV TX User Manual 8-PA 208VAC, Three-Phase AC Distribution Wiring Set-top fan Spare5 Spare4 Spare3 Spare2 Spare1 Exciter one Exciter two Controller Load Amp1 Amp2 Amp3 Amp4 Amp5 Amp6 Amp7 Amp8 Gnd 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Gnd UK35 F16-371/24VD A1 SIEMENS 3RT50461BB40 24v/50w Schneider C120H C100 AC Gnd - 1L1 3L2 5L3 2T1 4T2 6T3 A2 DC24V + AC208V L N Gnd KDY-20-4P 1 2 3 4 5 L1 L2 L3 Gnd UK50 Gnd PE Gnd Properly c
MHPTV TX User Manual 1.5 RF System Connections If you purchased an Anywave BPF, Anywave will install the BPF either on top of the TX cabinet (as shown below) or standing on the floor, according to the transmitter and the BPF’s dimension, unless it is specified with order. If it is installed on top of the TX cabinet, four metal stand-offs “feet” with mounting hardware are supplied with the BPF to allow it to be fastened and secured to four holes located in the top panel of the cabinet.