User's Manual

1
2
4
V/M
VOL
FUN
MAIN
MON
MIC
779UV
MIC
PPT
2
1
3
4
7
8
9
A
B
C
D
5
6
0
SQL
TONE
SCAN
BLK
REV
TOT
FUN
V/M
MAIN
DIL
SUB
RPT LAM
POW
SKIP
MON
V/M
VOL
FUN
MAIN
MON
MIC
779UV
PTT
MIC
MIC
PPT
2
1
3
4
7
8
9
A
B
C
D
5
6
0
SQL
TONE
SCAN
BLK
REV
TOT
FUN
V/M
MAIN
DIL
SUB
RPT LAM
POW
SKIP
MON
【UP】/【DN】
/
【UP】
【UP】/【DN】
/
»
779UV
V/M
FUN
MAIN
MON
VOL
2
1
3
4
7
8
9
A
B
C
D
5
6
0
S
Q
L
TONE
SCAN
B
LK
R
EV
TO
T
F
U
N
V
/
M
M
A
IN
D
I
L
S
U
B
R
P
T
LA
M
POW
S
K
I
P
M
O
N
P
P
T
M
IC
Instruction Manual
AT-779UV
1. WARNING
Transceiver
Screws
Microphone
Pads
Mobile Bracket
non-slip mat Fuse(10A 250V)
Adjusting screws
manual
2. ACCESSORIES
2.1
Standard Accessories
3. GETTING ACQUAINTED
3.1 Front panel
3.2 Rear panel
3.3 Microphone
VFO/Channel mode switch
Main channel
LCD
Up
Down
Indicator
Power on, volume switch
Menu
Monitor
Programming port/ microphone jack
Antenna jack
External speaker jack
Up /Down key
Indicator
Number key
4. BASIC OPERA
TIONS
4.1 Switching the Power On/Off
1. Turn the Volume knob clockwise to turn on the radio, the radio LCD will display
2. Power Of
f: Turn volume knob anti-clockwise until hear "click" to turn off the radio.
programmed text and emit a beep sound .
4.2
Adjusting the Volume
Turn volume knob clockwise to increase colume and anti-clockwise to reduce it.
4.3 Switch between Main Channel and Sub Channel
In standby states, press the microphpne key or front panel key to switch
between main channel and sub channel. The top left corner of LCD will display current
main channel .
4.4 Adjust
Channel
1. Press microphone key or front panel key to switch the radio to channel mode,
press microphone key or front panel key to choose channel .
2. In channel mode, input three numbers by number key to fast choose a channel.
4.5 Adjusting
Frequency
1. By number key: In VFO mode, yo
u can input wanted frequency by the microphone
number key. For example if want 145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want
145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over range.
2. By step size: In VFO mode, press microphone or front panel
【UP
】/【DN】
key can change frequency by step size.
Step size can be programmed by software from 2.5K to 50K.
4.5 Store channel
In standby states, press the microphpne key , the top left corner will display Func ,
then press KEY , the LCD bottom left corner will display Save to XXX,
now press key to choose a channel number, hold key to store the
new frequency and return to standby.
XXX stands for the channel number, if LCD displays “Null” under “Save TO XXX”,
means current channel is empty.
3
Qixiang Electon Science &
Technoloyg Co.,Ltd.
w w w
.qxdz.cn
【UP
】/【DN】
【# LAM】
4.6 Channel Delete
1.
In channe
l mode, press microphone key, then press key, the LCD displays
“Delete XXX” and frequency, presss key to choose the channel to delete,
【DN】
hold key delelte to current channel.
»
“XXX” stands for the channel number, the LCD displays “Null” after chennel deleted
(Europe version only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference.
GMRS Frequency List:
separation distance and the prohibition of operating to a person has been printed on the user’s manual.
Ω
cm between the radiator & body.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 71.372
For a transmitter that can only be operated with an FCC license,warningss concerning
compliance with applicable licensing requirements and information concerning license
applianction procedures.
Note: To get the best range from the external whip antenna(50 )should be used.
Ant:Tx GMRS, Rx:136-174&400-490Mhz, 0dBi . installation is height < 3m.