EMIV-DUAL V2.0 User Manual Application Information Sep. 29, 2006 01-EMIV-DUAL V2.0_X1 AnyDATA.NET AnyTime AnyPlace Any Wireless Data Solutions™ EMIV-DUAL V2.0 AnyDATA.
AnyDATA CDMA EMIV-DUAL V2.0 Copyright © 2005 AnyDATA Corp. All Rights Reserved. Any part of this document may not be distributed, communicated, reproduced or transmitted in any form or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of AnyDATA Corp. AnyDATA Inc. does not assume any liability arising out of the application or use of its products. AnyDATA Inc. assumes no responsibility for any damage or loss resulting from the misuse of its products. AnyDATA Inc.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information Contents 1 Introduction 1.1 Purpose 1.2 Organization 1.3 Revision History 2 Overview 2.1 Application Description 2.2 Technical Specifications 2.2.1 General Specification 2.2.2 Receive Specification 2.2.3 Transmit Specification 2.2.4 Standards 2.3 Interface Diagram 2.4 EMIV-DUAL V2.0 Photo 2.5 Internal Module Photo 3 PIN Description 3.1 8-Pin Connector (RS232 Standard) 3.2 3-Pin Connector (Debugging) 3.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 4 Interface Descriptions 4.1 Overview 4.2 RS232 Interface (Standard) 5 Electrical Specifications 5.1 Absolute Maximum Ratings 5.2 Recommended Operating Conditions 5.3 Power Consumption 5.4 Serial Interface Electrical Specifications 6 Mechanical Dimension 6.1 EMIV-DUAL V2.0 Outline 7 Installation Example EMIV-DUAL V2.0 AnyDATA.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 1. Introduction 1.1 Purpose This Manual provides hardware interface and programming information for EMIV-DUAL V2.0 CDMA Wireless Data Modem. 1.2 Organization The interface and operation section is organized into the following subsections: Section 2 – Introduces users to the EMIV-DUAL V2.0 CDMA Wireless Data Modem basic features and general specifications. Section 3 – Contains EMIV-DUAL V2.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2. Overview 2.1 Application Descriptions The CDMA Wireless Data Modem is a complex consumer communications instrument that relies heavily on both digital signal and embedded processor technologies. The Wireless Data Modem manufactured by AnyDATA.NET supports Code-Division-Multiple-Access (CDMA). This operates in 800MHz CDMA and 1900MHz PCS spectrum.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2.2 Technical Specifications 2.2.1 General Specifications Parameters Descriptions External Access Code-Division-Multiple-Access (CDMA) CDMA Protocol IS-95 A/B, IS-126, IS-637A, IS-707A, IS-2000 Data Rate 153 Kbps max. on both the forward and reverse links Transmit/Receive Frequency Interval 45MHz for Cellular and 80MHz for PCS Band Width 1.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2.2.2 Receive Specifications Parameters Descriptions 869.04 ~ 893.97 MHz for 800MHz CDMA and Frequency Range 1931.25 ~ 1988.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2.2.4 Standards IS-95A/B/C : Protocol Between MS & BTS IS-96A : Voice Signal Coding IS-98A : Base MS Function IS-126 : Voice Loop-Back IS-637 : Short Message Service IS-707 : Data Service Built-in TCP/IP : AnyDATA proprietary software IS-657 : packet data EMIV-DUAL V2.0 AnyDATA.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2.3 Interface Diagram Figure 2-1 Interface Block Diagram EMIV-DUAL V2.0 AnyDATA.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 2.4 EMIV-DUAL V2.0 Photo Figure 2-2 EMIV-DUAL V2.0 Photo 2.5 Internal Module Photo CDMA Connector Figure 2-3 Internal Module Photo (DTG2000-DUAL V2.0) EMIV-DUAL V2.0 AnyDATA.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 3. PIN Description 3.1 8-Pin Male Modular Jacks (RS232 Standard) Molex (85503) RS-232 (Host) Pin 1 RI Pin 2 GND Pin 3 DTR Pin 4 CTS Pin 5 TX Pin 6 RTS Pin 7 RX Pin 8 DCD Figure 3-1 Right Angle Modular Jacks Pin Description (85503,Molex 8P) 3.2 Debug Connector VCC RXD TXD NC GND Figure 3-2 Debugging Connector (UX60-MB-5S8) 3.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 4. Interface Descriptions 4.1 Overview This chapter covers information required to design the EMIV-DUAL V2.0 into a subscriber unit application. In addition, the internal signals that are necessary for complete understanding of the UART interfaces are described below. 4.2 RS232 Interface (Standard) The Universal Asynchronous Receiver Transmitter (UART) communicates with serial data that conforms the RS-232 Interface protocol.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 5. Electrical Specifications 5.1 Absolute Maximum Ratings Operating the modem under conditions that exceed those listed in the Absolute Maximum. The Ratings table may result in damage to the modem. Absolute Maximum Ratings may be considered as limiting values, and are considered individually.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 6. Mechanical Dimensions 6.1 EMIV-DUAL V2.0 Outline EMIV-DUAL V2.0 AnyDATA.
Interface Description EMIV-DUAL V2.0 Reference Manual Application Information 7. Installation Example EMIV-DUAL V2.0 AnyDATA.
