Quick Start Guide

1
1
11
11
10
2
2
3
5
4
6
3
4 5 6
8
7
9
12
10
11
13
15
14
Follow the instructions in the owner's manual of your TV or converter box to change the input from ‘CABLE’ to ‘ANTENNA’, ‘AIR’, or ‘BROADCAST’.
FRONT VIEW ON MAST
Call to Learn.
Toll-Free Helpline:
1-877-825-5572
Point the front of the antenna in the direction of your TV stations' broadcast towers and check reception by
scanning for channels. If you are not receiving all of the available channels, move the antenna and rescan.
To add the mounting
hardware, assemble
the hardware, as
shown, and use the
Mast Clamp Bolts (9)
to secure.
Before installing the antenna on the J-Mount Mast (8), adjust the mast,
so it is in a vertical position. You will need to adjust the antenna aer it
is mounted for the best reception.
Install the antenna on
the J-Mount Mast (8) by
positioning the Mast
Clamp (10) around the
mast. Tighten the Wing
Nuts (11) to secure the
antenna to the mast.
J-MOUNT INSTALLATION
Attach the J-Mount Mast (8) to the Mount Base (14) with
the Hex Bolts and Nuts (12), as shown above.
Mark the Mount Base (14) position on the desired surface
and drill pilot holes, 1" deep, for each of the 50mm
J-Mount Bolts (13).
Place the Sealing Pads (15) over the pilot holes, and the
Mount Base (14) on top of the Sealing Pads.
Tighten the J-Mount Bolts (13) to secure the base to the
surface.
INSTALLATION ON THE J- MOUNT MAST
Technical Assistance is available Monday – Friday, 9:00 am to 9:00 pm
and Saturday – Sunday, 10:00 am to 6:00 pm, Central Time.
The ClearStream 4MAX™ comes with:
1) 2- Antenna Elements
2) Antenna Spine with 2 Short Tubes
3) 2 - VHF Dipoles
4) 2 - 19mm Dipole End Cap Screws
5) 2 - Dipole End Caps
6) 2 - 60mm Antenna Spine Bolts
7) Mast End Cap
8) J-Mount Mast
9) 2 - 25mm Mast Clamp Bolts
10) Mast Clamp and Back Plate
11) Wing Nuts and U-Clamp
12) 2 - 40mm Hex Bolts and Nuts
13) 4 - 50mm J-Mount Bolts
14) Mount Base
15) 4 - Sealing Pads
Attach the Antenna
Elements (1) to the
Antenna Spine (2) by
placing the Short Tubes (2)
in the spine holes, and
screwing in the 60mm
Antenna Spine Bolts (6).
Next, add the VHF Dipoles (3) using the Dipole End Caps (5) and the
19mm End Cap Screws (4).
13
15
14
WALL MOUNT
8
12
9
14
7
Quick Start Assembly/Installation Instructions
Before beginning assembly, make sure all parts needed are present.
Coaxial cable sold separately.
Connect the antenna to the TV or converter box and run a full channel scan. If reception is not as desired, move the antenna and rescan for the available channels.
CLEARSTREAM 4MAX™
To locate the broadcast towers in your area, go to
antennapoint.com and enter your zip code, or scan the
QR code.
HELPFUL TIP: IT'S IMPORTANT TO CHECK THE RECEPTION IN THE LOCATION
WHERE YOU INTEND TO INSTALL THE ANTENNA, PRIOR TO ATTACHING THE
J-MOUNT MAST TO ANY SURFACE.
Required: Coaxial Cable (sold separately), Adjustable Wrench, Power Drill, 3/16" Drill Bit,
8 and 10mm Ratcheting Drivers, and a #2 Phillips Screwdriver
Before permanently attaching the antenna to any surface, TEST RECEPTION
in that area.