DIY Do-It-Yourself Quick Start Guide Wireless NVR System With H.
FCC Warning This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference that is received, including any interfer ence that may cause undesired operation. Manufacturer: Ansjer Electronics Co., Ltd RF exposure warning : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
IMPORTANT! This instruction guides you how to install surveillance system. What accessories you need before getting started 1.One monitor or TV,can not be less than 19" 2.One VGA Cable/one HDMI Cable,use any one that monitor supports 3.One surge protector (advisable) 4.Power supplies for the NVR and cameras. Only use approved PSU's from your supplier. 5.Appropriate tools for installation. Note: This instruction guide provides basic information on how to install your CCTV system.
B SETTINGS WIZARD Before turning on your NVR, ensure that all connections are correctly installed. POWER ON AND LOGIN Connect the NVR with the power supply to start-up. The light labelled POWER on the front bezel will illuminate. After the NVR start-up, a Wizard Setting panel displays to choose your required settings, including language, date format, time format, time zone, system date & system time as shown below.
CHANGING DISPLAY RESOLUTION Optimize the NVR Video output to match the monitor output, using the following steps: NB: Make sure the monitor supports the same resolution as your NVR output resolution, otherwise the monitor will be unable to display the video. STEP 1. Right click mouse for quick shortcut menu and select Main Menu STEP 2. Click Setup, then choose Basic menu STEP 3. Select the desired Video Output resolution STEP 4. Click Apply to save the settings STEP 5.
D PLAYBACK Go to system Main Menu--Search, view the following screen. Play/Pause Fast Forward Rewind Previous Next frame frame Multi-screen display Single-screen display Previous Record Next Record Previous Record: Move to last recorded event Next Record: Move to next recorded event Select the channel Fast Forward: video can be played at different speeds, from x1, x4 to x16 speed. Start playing Rewind: Video can rewind at x1, x8, x16 & x32 speed.
REMOTE SURVEILLANCE GUIDE F Step 1.
2). Enter the NVR menu interface to restore it to the factory settings; Main Menu-Setup-Advanced-Reset. 3).Connect the NVR and WiFi camera by RJ45 cable, as shown in figure 2. 4).Enter the NVR interface, right click the mouse, select “IPC Channel Config”, as shown in figure 3. Figure 2 Figure 3 5).Click “search”, WiFi camera IP address is displayed, then click “WiFi add” to add the camera to NVR system, as shown in Figure 4 and Figure 5. Figure 4 Figure 5 6).
Personal Account Registration ● Start the mobile app ADCloud ● Click “Register ” in the bottom of interface ● Input your mobile phone number to get validation code,click Next to input email box, password,then save it. Login Interface Registration Login Password Setting Note: Email box is used to retrive password when it is forgotten. Add Device Login the app,get into the main interface(My Device),click”+”in the upper right corner,three different options of device addition are available.
2.QR Code Scanning ● Find UID QR Code(in DVR label and DVR system) ● Click Scan QR Code to get the Device ID ● Input Password(Same as DVR system login),Device Name ● Click √ to save 3.Local Search ● Turn on mobile phone WiFi setting,make it connect with the same LAN as DVR’s ● Click Local Seach,Device ID will be displayed in a few seconds ● Choose the intended ID to add ● Input password(Same as DVR system login),Device name ● Click √ to save App Function Introduction 1.
Device Information Video Preview B: PC Client Remote Monitoring The PC Client AVSS is applied for DVR,NVR,IPC, with functions live view, Device management, remote video playback,etc. Ask for AVSS from the local distributor or download it from the link www. nsst.com (If available). 1.Login Install the PC Client,double click the icon AVSS to open, choose language and click to Login. Note: use the default user name and passpword, or enter the same login information as your mobile App. 2.
Add Area. Right Click mouse in the blank to add area and enter area name. Area name is used to describe the monitored place. Add Device. Right Click Mouse on Area name to add device, change the device type, enter device name, device ID, user name, device password and channel number, then click OK to save. 3. Preview Click preview to find device list, right click device to Play All and Stop All, preview video can be displayed or stopped.
4. Playback Click Playback, select the Device ID, Channel number, Date, then Searching to find the video, double click the Recording Time to fix the exact time, then click Start Play. FAQ: 1).Q: Why failed to search the device when adding ? A:Make sure the device and mobile are in the same local area network,otherwise Enter Device ID by manual 2).Q:Why the device is offline ? A:Please check ● If device has been connected to Internet ● If Router working fine ● If DHCP server of Router turned on or not 3).