Specifications

ManualsBrandsAnhui NARI Zenith Electricity & Electronic ManualsElectronicsNRZT Wi-SUN Module

Table Of Contents

brief introduction

NRZT-RN-P915 is an antenna external surface mounted with Wi-SUN module equipped with

core VC7300, a maximum emission power of 21.089dBm, effectively solving the problem of

insufficient distance due to emission power.The series of modules meet the Wi-SUN

protocol standards, Sub-GHz frequency band, applicable to the global frequency band, with

interchangeable, reliable, economic characteristics, advanced wireless network (Mesh)

communication technology, can be widely used in wireless intelligent public networks and

related applications, has been certified by

the Wi-SUN alliance.

Size (unit:

mm) M

Summary of content (10 pages)

PAGE 1
brief introduction NRZT-RN-P915 is an antenna external surface mounted with Wi-SUN module equipped with core VC7300, a maximum emission power of 21.089dBm, effectively solving the problem of insufficient distance due to emission power.
PAGE 2
odule pin Specifications parameters modulation mode GFSK Working frequency band (MHZ) 902-928 working temperature -40-85℃ working voltage 5V transmitting power 21.
PAGE 3
communication interface UART size dimension 28*22*3.1mm attended mode SMD standard IEEE802.15.4G/E, Wi-SUN, Wireless M-Bus, 6LoWPAN functional characteristics The SMD packaging mode, with the maximum emission power of 30dBm and the reception sensitivity of-110dBm, can self-repair the network in a large-scale Mesh network in a crowded environment, providing a long-distance, anti-interference-resistant intelligent network for smart meters, smart street lamps and other industries.
PAGE 4
Insufficient power supply leads to abnormal module emission power. The test environment is bad, and the signal attenuation is great. The module passes through the wall and the other end of the communication, the wall and other signal attenuation, most of the signal is bypassing the wall signal attenuation.
PAGE 5
FCC WARNING FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
PAGE 7
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
PAGE 8
module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured.
PAGE 9
The module manufacturers shall provide a list of acceptable unique connectors. Explanation: The EUT has one Chip antenna, the antenna can be replaced by other authorized antennas, and the gain of each replacement antenna is no more than 1.0dBi 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules.
PAGE 10
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.