User's Manual

ManualsBrandsAngelcare Monitors ManualsBaby MonitorsDigital Video Baby Monitor - Parent Unit

1) Press Menu icon to access

main menu.

2) Press sound icon to activate

or deactivate sound.

3) Press OK icon to confirm.

5.2 - SOUND

TO TEST SOUND:

Ask someone to speak into the Nursery

Unit or place the unit near a radio to ensure

that sound is being picked up.

ADJUST SOUND LEVEL PUT IN SILENT/MUTE MODE PUT IN DIALOGUE MODE

Raise volume (+)

Lower volume (-)

Press the (-)

button for 2

seconds to

mute sound.

Press and hold

talk button to

speak to baby.

ON OFF

TO ACTIVATE SOUND:

5.3 - BATTERIES

HOW TO CHECK THE BATTERIES:

Unplug the Adapters from both units.

• If the green light on the Nursery Unit does not show, replace the batteries.

• If the Parent Unit and its screen do not light up, recharge the batteries.

IF YOU HEAR NO SOUND:

• Check that both units are powered on.

• Check that both units are plugged

into functioning electrical outlets.

• Check the batteries in both units

(replace or recharge them if necessary).

• Bring Parent Unit closer to Nursery Unit.

IMPORTANT

To avoid feedback (whistling), keep

both units at least 3 m apart.

HOW TO CHARGE THE BATTERIES IN THE PARENT UNIT:

Leave the Parent Unit in the Charging Cradle

to fully charge the unit. Although the batteries

at 1/3 capacity works normally, we recommend

that you fully recharge them.

1/3 full 2/3 full full

PARENT UNIT BATTERY ALARM

• Alarm activates when the batteries need to be recharged.

• Parent Unit will emit a beep sound every 15 seconds.

• Battery Alarm icon will show on LCD screen.

Summary of content (8 pages)

PAGE 1
5.2 - SOUND 1) Press Menu icon to access main menu. TO ACTIVATE SOUND: 1 2) Press sound icon to activate or deactivate sound. 2 ON OFF OK 3) Press OK icon to confirm. TO TEST SOUND: Ask someone to speak into the Nursery Unit or place the unit near a radio to ensure that sound is being picked up. IMPORTANT To avoid feedback (whistling), keep both units at least 3 m apart. ADJUST SOUND LEVEL IF YOU HEAR NO SOUND: • Check that both units are powered on.
PAGE 2
YOU ARE NOW READY TO USE YOUR MONITOR The Angelcare® monitor can be used with the pre-program factory settings or you can also customise your settings to your preference.
PAGE 3
STEP 6 - ACTIVATING AND DEACTIVATING ADDITIONAL FUNCTIONS IMPORTANT When in the menu or sub-menu modes, sound transmission between Parent and Nursery Units will be temporarily deactivated. ONLY the motion-detection alarm will remain active (if function is activated). All changes and adjustments made in the main menu and sub-menus will not be activated unless you confirm them by pressing the OK icon. OK 6.
PAGE 4
6.2 - ALARM Allows you to select your preferred alarm mode for the Parent Unit. 1 3 2 1) Press the Menu icon to access main menu. OFF 2) Press the settings icon to access sub-menu. ON ON OK OK 3) Press the Alarm icon to change the alarm mode. 4) Press OK to confirm. Sound alarm only Alarm Mode icon shows in the top bar of the Parent Unit. Sound alarm and vibration Sound alarm will replace vibration mode when the Parent Unit is in its Charging Cradle.
PAGE 5
6.4 - THERMOMETER TO CHANGE THE MEASUREMENT UNIT: 1 3 2 o 30 C + o 15 C o ON C ºC ºF OK OK 1) Press the Menu icon to access main menu. 2) Press the temperature icon to access sub-menu. 3) Press the ˚C ˚F icon to change from Celsius to Fahrenheit. 4) Press OK to confirm. o o C ºC ºF Celsius F ºC ºF Fahrenheit TO ACTIVATE THE TEMPERATURE ALARM: 1 3 2 1) Press the Menu icon to access main menu. o 30 C + o 2) Press the temperature icon to access sub-menu.
PAGE 6
.5 - VIDEO Allows you to turn video function ON or OFF. 1 1) Press the Menu icon to access main menu. 4 2 2) Press the Video icon to activate or deactivate the video function. 3 3) Press OK to confirm. OFF OK 4) Press the Menu icon to return to main menu. ON OFF 6.6 - SCREEN SAVER Allows you to set the screen saver starting point. 1 2 1) Press the Menu icon to access main menu. OFF 3 2) Press settings icon to access sub-menu.
PAGE 7
6.7 - INFRARED NIGHT VISION Allows you to capture image when lighting is unsufficient. TO ACTIVATE NIGHT VISION: Press the Night Vision icon to chose available modes: AUTO: The infrared LEDS will turn on automatically when the lighting is not sufficient. The image transition takes 20 seconds ON: The infrared LEDS are ON at all times. OFF: The infrared LEDS are OFF at all times. There are 4 built-in infrared LEDs on the Nursery Unit to enable clear black and white image.
PAGE 8
6.10 - ZOOM MODE Allows you to zoom in to twice the normal view. 1 2 1) Press the zoom icon. 2) Press the directional arrows to zoom in on what you want to see more closely. 3) Press the zoom icon again to return 3 to normal view. 6.11 - MUTE Allows you to put your monitor in Silent/Mute mode TO PUT ON MUTE: Press the (-) button and hold for 2 seconds to mute sound. TO UNMUTE: NOTE: Press the (-) button again and hold for 2 seconds to unmute sound. On the Parent Unit, the Mute ICON will blink. 6.