Mobile Elite 4G QUICK START GUIDE Personal Emergency Response System Table of Contents Page 1
Items in your Box ............................................................. 3 Step 1: Reading the Directions ......................................... 5 Step 2: Preparing your System ......................................... 6 Step 3: Activating your System ......................................... 7 Step 4: Talking to the Call Center ..................................... 8 Step 5: Wearable Accessories ........................................... 9 Step 6: Setting up your Wearable .......................
Items in your Box Mobile Elite 4G Phone, charging cradle and power cord.
Items in your Box Speaker Network LED Power LED ON/OFF Button EMERGENCY Call Button MESSAGE Button USB on cradle for home use Microphone Charger Pins Power LED Plug into Wall Socket Plug USB into back of Cradle LED Call Indicator (Green or Red) Page 4
Step 1: Reading the Directions 1) Please take a few minutes to read through this quick start guide so you will be familiar with the steps required to set up your Mobile Elite 4G System. 2) Please make sure someone is with you while you are setting up and testing your system. 3) The Mobile Elite 4G Phone is programmed with multiple audio prompts to make it easier to use. Please follow the audio prompts if they occur.
Step 2: Preparing your System 1) Locate a place in your home that is central and is near a standard wall outlet. It should be easy to access for daily charging and to allow you to take the Mobile Elite 4G Phone with you when you leave the house. 2) Plug the Power Cord into a wall socket not controlled by a switch and the small end into your Charging Cradle.
Step 3: Activating your System 1) Your Mobile Elite 4G Phone will prompt you and guide you through the remaining setup. 2) When your Mobile Elite 4G Phone has sufficient charge, it will say “Hello, it’s time to test your system to make sure it is working properly. Please press and hold your EMERGENCY Call Button for three seconds now to allow us to confirm that your system is working properly.” 3) Press and hold the EMERGENCY Call Button for three seconds.
Step 4: Talking to the Call Center 1) The operator should have your name from your original order form, as well as the address where your cradle will be located. The operator will confirm: a. Your name b. Your Cradle address ** c. The quality of your call d. Your Mobile Elite 4G Phone location 2) The Mobile Elite 4G Phone will automatically end the call when the operator hangs up. 3) The Mobile Elite 4G Phone will announce “Your call has ended. Thank you.
Step 5: Wearable Accessories 1) The Wearable Button can be exchanged between the Wristband and Pendant. Locate your Wearable Button in the plastic tri-fold box. a. Turn the Wristband or Pendant accessory so the front is resting on a solid surface. You are now looking at the back of the accessory. You will insert the Wearable Button into the Wristband or Pendant accessory from the back. With the grey button side facing down, push the button into the accessory.
Step 6: Setting up your Wearable 1) The Wearable is ready to use. Please make sure someone is near your Mobile Elite 4G Phone when testing your Wearable. 2) Press the center of the Wearable (this is where the call button is located) for three seconds. 3) You will feel the click of the Button when you first push it. Hold the Button down until the green LED turns on (3 seconds) and then RELEASE it. You will see the LED at the top of the button start to flash.
Step 7: Care4Mom App 1) Your loved ones can keep in touch with you using the Care4Mom app. It may be downloaded from the Apple or Google store. A link to the Apple store may be found at www.anelto.com under the subsection Caregiver Solutions. You may also use this app yourself if you have an Android or iOS smartphone.
Step 8: Receiving Messages 1) Your loved ones may send you messages using the Care4Mom app. They may wish to remind you of a doctor’s appointment or just wish you a good day. 2) Your Mobile Elite 4G Phone may also automatically send you reminder messages when needed. 3) When you see the green LED blinking on the MESSAGE Button, push the button and listen to the message. You may wish to have a notepad and pencil ready in case you need to jot down any information.
Quick Reference: General Information 1) When traveling on a plane, press the ON/OFF button on top of the Mobile Elite 4G Phone and hold it down for five seconds to turn it off. Your Mobile Elite 4G Phone will announce, “Your device is powering down now”. Turn the Mobile Elite 4G Phone back on at the end of your flight by again pressing and holding the ON/OFF button for five seconds. Your Mobile Elite 4G Phone will announce “Your device is now ready”.
Quick Reference: LED Indicators The following is a guide to the LED indicators on the Cradle, Phone, and Wearable: 1) CRADLE GREEN LED – Solid green: Cradle is plugged in and has power. No LED: Cradle has no power. 2) Mobile Elite 4G PHONE GREEN LED (above Signal icon) – Solid Green: Mobile Elite 4G Phone is registered to network and able to make calls. Blinking Green: Mobile Elite 4G Phone is attempting to register to the network.
Quick Reference: LED Indicators #2 #3 #4 #5 #1 #6 Page 15
Important Tips and Reminders 1) Important: Your iOnMom Mobile Elite 4G Phone requires adequate battery charge and cellular signal to make an emergency call. 2) The GREEN LED Message system allows us to keep in touch with you and provide you with important information. Please Press the green Message Button whenever it is lit to listen to these messages. 3) The iOnMom Wearable Button is water resistant, but it is not waterproof. It can be splashed, but it should not be submerged.
Regulatory Compliance: FCC/IC The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the United States FCC regulations and has an Industry Canada registration (IC ID) of 20951-ANH0319.
FCC ID: 2AGPI-ANH0319 IC:20951-ANH0319 Model: ANH0319 Contains FCC ID: XMR201606EC21A IC:10224A-201611EC21A Model: Quectel EC21-A Conformité réglementaire : FCC/IC Le manuel ou le manuel d'instructions de l'utilisateur pour un radiateur intentionnel ou non intentionnel doit avertir l'utilisateur que des modifications ou des modifications non expressément approuvées par la partie responsable de la conformité pourraient annuler l'autorisation de l'utilisateur d'utiliser l'équipement.
l'équipement, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes : Réorienter ou déplacer l'antenne réceptrice. Augmenter la séparation entre l'équipement et le récepteur. Connectez l'équipement à une prise sur un circuit différent de celui auquel le récepteur est connecté. Consultez le concessionnaire ou un technicien expérimenté en radio/télévision pour obtenir de l'aide.
Regulatory Compliance: RF Exposure Your device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emissions limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and Industry Canada of the Canadian Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
Conformité réglementaire : Exposition rf Votre appareil est un émetteur radio et un récepteur. Il est conçu et fabriqué pour ne pas dépasser les limites d'émissions pour l'exposition à l'énergie par radiofréquence (RF) fixées par la Federal Communications Commission (FCC) du gouvernement des États-Unis et D'Industrie Canada du gouvernement canadien. Ces limites font partie des lignes directrices exhaustives et établissent des niveaux autorisés d'énergie RF pour la population en général.
HAVE QUESTIONS? Please refer to the more detailed information at www.anelto.com or contact your Dealer.