Operating Manual Metris Vibe Ex Revision: 03 00 25.02.2019 Operating Manual PJO 01 16.02.2021 Operating Manual EPG 02 03.03.2021 Operating Manual EPG 03 22.03.2022 Operating Manual EPG Confidential document. All rights reserved. No duplication or disclosure to third parties permitted without written consent from ANDRITZ. ANDRITZ AG Stattegger Strasse 18 8045 Graz, Austria Phone: +43 (316) 6902 0 Fax: +43 (316) 6902 415 www.andritz.
Operating manual: Metris Vibe Rev.: 03 Table of Contents Abbreviations ......................................................................................................................................... 3 Preface .................................................................................................................................................... 4 Information on the manufacturer .........................................................................................................
Operating manual: Metris Vibe Rev.
Operating manual: Metris Vibe Rev.: 03 PREFACE The present operating manual contains the information required according to valid regulations (2014/30/EU, 2014/53/EU, 2011/65/EU, 2014/34/EU) for transport, installation, operation, and maintenance of the vibration sensor METRIS VIBE. The manual is intended for persons who work with the METRIS VIBE described herein. The only way to avoid faults in the equipment and guarantee trouble-free operation is to follow this operating manual.
Operating manual: Metris Vibe Rev.: 03 INFORMATION ON THE MANUFACTURER ANDRITZ AG Stattegger Strasse 18 A-8045 Graz, Austria Phone: +43 (316) 6902 0 Fax: +43 (316) 6902415 www.andritz.com (referred to below as “ANDRITZ”) Legal form: Corporation Company seat: Graz, Court of registry Landes- und Handelsgericht Graz Company reg. no.: FN 50935 f, DVR: 005 0008, ARA license no.
Operating manual: Metris Vibe Rev.: 03 1 INTRODUCTION This manual is describing the METRIS VIBE sensor supplied by ANDRITZ. Condition Monitoring Systems (CMS) are described as systems that monitor the condition of machines and systems to provide advanced detection or prediction of damage. As consequences increased vibrations are indicating increased wear, damage to bearings, rotating parts, the frame of the machine or the building.
Operating manual: Metris Vibe Rev.: 03 • Incorrect start-up and operation of the METRIS VIBE sensor. • Use of the METRIS VIBE sensor for purposes other than its intended use. • Unauthorized structural changes or additions to the METRIS VIBE sensor that do not conform to the basic configuration supplied and tested as well as changes to the user software. 1.
Operating manual: Metris Vibe Rev.: 03 1.6 SHIPPING NOTICE Special symbols are printed on the packaging according to common international practice. It is important to take these symbols into account when loading, unloading, or moving the goods. Non-compliance with these instructions can result in material damage. If in doubt, always ask the manufacturer to organize a suitable solution.
Operating manual: Metris Vibe Rev.: 03 Da m a g e Check the deliveries immediately for visible damage upon arrival at the place of destination, preferably in the presence of the forwarding agent. In fo rm a tio n Care must be taken to ensure that special packaging is not damaged during the inspection. In case of obvious transport damage proceeds as follows: 1. Take photos of the transport damage. 2. Open the damaged package only to the point where damage to components can be verified and documented.
Operating manual: Metris Vibe Rev.: 03 In fo rm a tio n Follow the respective disposal instructions for environmentally friendly disposal of the packaging. 1.7.3 STORAGE NOTICE Parts that are not stored correctly can suffer damage after a short period of time due to climatic influences, resulting in a need for repeat treatment or re-machining. Always follow the manufacturers’ information regarding storage of individual parts.
Operating manual: Metris Vibe Rev.
Operating manual: Metris Vibe Rev.: 03 1.7.3.1 STORAGE OF METRIS VIBE SENSORS The following information should be considered when putting METRIS VIBE sensors into storage: It is p o s s ib le to s to ra g e th e METRIS VIBE Ex s e n s o rs u p to 2 ye a rs if th e s e n s o r is n o t a c tiva te d .
Operating manual: Metris Vibe Rev.: 03 2 SAFETY Safety instructions for components that were not manufactured by ANDRITZ are included in the descriptions of the component suppliers and must be obeyed as well. 2.1 SAFETY INSTRUCTIONS Everything mentioned in the Safety section is important and safety-relevant.
Operating manual: Metris Vibe Rev.
Operating manual: Metris Vibe Rev.: 03 3. METRIS VIBE SENSOR START UP 3.1 ACTIVATING THE METRIS VIBE FROM STORAGE MODE It is necessary to activate the Metris Vibe sensor from storage mode before installing it on equipment. This is possible with the Metris Vibe mobile App. In the App you have to connect for the first time with the sensor for activation. When using the gateway router this happens automatically. The serial number is printed on each sensor starting with Axxxx. 3.
Operating manual: Metris Vibe Rev.: 03 It is very important to mount the sensor according the installation instruction. 3.3 DOWNLOADING DATA To download data from the sensor Blue Tooth LE is used. Therfore 2 (two) possibities are foreseen to get access to the required data. • Industrial Gateway routers Data is downloaded from sensor, automatically, via industrial gateway routers. • Smartphone or Tablet Data is downloaded from sensor, manually, using the METRIS VIBE mobile App.
Operating manual: Metris Vibe Rev.: 03 3.5 SPECIAL CONDITIONS The ambient temperature range is set from -40°C to +85°C. Category 1 equipment The vibration sensor may only be operated in an explosive atmosphere, which requires equipment of category 1, if atmospheric conditions exist (temperature from –20°C to + 60°C, pressure from 0.8 bar to 1.1 bar). 4. REPAIR NOTICE No Reparing possible If the METRIS VIBE sensor is damaged it is not possible to repair it.
Operating manual: Metris Vibe Rev.: 03 5. DECOMMISSIONING If the METRIS VIBE sensor is no longer fit for use and is to be scrapped, it must be decommissioned and disassembled. 5.1 DISPOSAL Comply with all national, regional and local legal requirements and regulations during the disposal or recycling of parts and components of the METRIS VIBE sensor as well as of materials needed to operate it.
Operating manual: Metris Vibe Rev.: 03 6.
Operating manual: Metris Vibe Rev.: 03 7.
Operating manual: Metris Vibe Rev.: 03 8.
Operating manual: Metris Vibe Rev.: 03 9.
Operating manual: Metris Vibe Rev.: 03 10. FCC AND ISED INFORMATION This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Operating manual: Metris Vibe Rev.: 03 10.2 RF EXPOSURE INFORMATION ACCORDING 2.1091 / 2.1093 / KDB 447498 / RSS-102 Radiofrequency radiation exposure Information The radiated output power of the device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. 10.3 USED FREQUENCE RANGE, USED MODES AND ANTENA INFORMATION Frequence range 2.402 - 2.
Operating manual: Metris Vibe Rev.
