® ION -M7P/17EHP/19P Optical Remote Unit (M2-Cabinet) Manual MF0150A4A
DISCLAIMER: This document has been developed by CommScope, and is intended for the use of its customers and customer support personnel. The information in this document is subject to change without notice. While every effort has been made to eliminate errors, CommScope disclaims liability for any difficulties arising from the interpretation of the information contained herein.
Table of Contents TABLE OF CONTENTS 1. GENERAL 5 1.1. USED ABBREVIATIONS 5 1.2. HEALTH AND SAFETY 6 1.3. PROPERTY DAMAGE WARNINGS 6 1.4. COMPLIANCE 7 1.5. ABOUT COMMSCOPE 11 1.6. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 12 2. INTRODUCTION 14 2.1. PURPOSE 14 2.2. THE ION-M7P/17EHP/19P 14 3. COMMISSIONING 16 3.1. 3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5.
Figures and Tables 6. APPENDIX 47 6.1. ILLUSTRATIONS 47 6.2. 6.2.1. 6.2.2. 6.2.3. 6.2.4. SPECIFICATIONS SW Requirements Electrical Specifications Environmental and Safety Specifications Mechanical Specifications 48 48 48 48 48 6.3. SPARE PARTS 49 7. INDEX 50 FIGURES AND TABLES figure 4-1 Wall mounting - pitches .............................................................................. 18 figure 4-2 Pole mounting - pitches .....................................................................
1. General 1. General 1.1.
1. General 1.2. Health and Safety 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 3.
1. General 7. Notice: Read and obey all the warning labels attached to the unit. Make sure that all warning labels are kept in a legible condition. Replace any missing or damaged labels. 8. Notice: Only license holders for the respective frequency range are allowed to operate this unit. 9. Notice: Make sure the repeater settings are correct for the intended use (refer to the manufacturer product information) and regulatory requirements are met.
1. General 3. Notice: For installations which have to comply with FCC/Industry Canada requirements: English: This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with Health Canada’s Safety Code.
1. General 4. Notice: Installation of this equipment is in full responsibility of the installer, who has also the responsibility, that cables and couplers are calculated into the maximum gain of the antennas, so that this value, which is filed in the FCC Grant and can be requested from the FCC data base, is not exceeded. The industrial boosters are shipped only as a naked booster without any installation devices or antennas as it needs for professional installation. 5.
1. General Equipment Symbols Used / Compliance Please observe the meanings of the following symbols used in our equipment and the compliance warnings: Symbol --- Page 10 Compliance Meaning / Warning FCC For industrial (Part 20) signal booster: WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.
1. General 1.5. About CommScope CommScope is the foremost supplier of one-stop, end-to-end radio frequency (RF) solutions. Part of the CommScope portfolio are complete solutions for wireless infrastructure from top-of-the-tower base station antennas to cable systems and cabinets, RF site solutions, signal distribution, and network optimization. For patents see www.cs-pat.com. CommScope has global engineering and manufacturing facilities.
1. General 1.6. International Contact Addresses for Customer Support Canada United States CommScope Canada Andrew LLC, A CommScope Company Mail 505 Consumers Road, Suite 803 Toronto M2J 4V8, Canada Mail 620 North Greenfield Parkway Garner, NC 27529, U.S.A. Phone +1-905-878-3457 (Office) +1-416-721-5058 (Cell) Phone +1-888-297-6433 Fax +1-905-878-3297 A Fax E-mail wisupport@commscope.com Caribbean & South American Region CommScope Cabos do Brasil Ltda.
1. General United Kingdom Scandinavia Andrew Wireless Systems UK Ltd Andrew Norway (AMNW) Mail Unit 15, Ilex Building Mulberry Business Park Fishponds Road Wokingham Berkshire RG41 2GY, England Mail P.O. Box 3066 Osloveien 10 Hoenefoss 3501 Norway Phone +44-1189-366-792 Phone + 47 32-12-3530 Fax +44-1189-366-773 Fax + 47 32-12-3531 E-mail wisupport.uk@commscope.com E-mail wisupport@commscope.
2. Introduction 2. Introduction 2.1. Purpose Cellular telephone systems transmit signals in two directions between base transceiver station (BTS) and mobile stations (MS) within the signal coverage area. If weak signal transmissions occur within the coverage area because of indoor applications, topological conditions or distance from the transmitter, extension of the transmission range can be achieved by means of an optical distribution system.
2. Introduction The ION can be easily set-up and supervised from a graphical user interface (GUI). Remote units are commissioned through the use of built-in test equipment. An auto leveling function compensates for the optical link loss making installation easy and quick. The entire system as well as complete network of systems can be managed remotely most efficiently by Commscope`s A.I.M.O.
3. Commissioning 3. Commissioning Read and observe the health, safety, and property damage warnings as well as the description carefully to avoid mistakes and proceed step-by-step as described. Attention: Do not operate the Remote Unit without terminating the antenna connectors. The antenna connectors may be terminated by connecting them to their respective antennas or to a dummy load.
3. Commissioning 6. Notice: If any different or additional mounting material is used, ensure that the mounting remains as safe as the mounting designed by the manufacturer. The specifications for stationary use of the Remote Unit must not be exceeded. Ensure that the static and dynamic strengths are adequate for the environmental conditions of the site. The mounting itself must not vibrate, swing or move in any way that might cause damage to the Remote Unit. 7.
3. Commissioning 3.1.3. Wall-Mounting Procedure Notice: It is the responsibility of the installer to verify that the supporting surface will safely support the combined load of the electronic equipment and all attached hardware and components and to ensure that the RU is safely and securely mounted. 1. Mark the position of the drilling holes (for pitches refer to figure 3-1 Wall mounting). Drill four holes at the marked positions and insert dowels*. 2.
3. Commissioning 3.1.4. Pole Mounting with screw bands Standard mounting hardware cannot be used to mount the Remote Unit to a pole, a column, or other similar structures. Additional hardware must be used for this type of installation. The pole-mounting kit includes two mounting brackets with screw bands, (worm gear) clamps to mount the brackets to the pole and two M8x25 screws, flat washers, and split lock washers per bracket to attach the Remote Unit to the bracket. A 775 min. 788 max.
3. Commissioning 3. Hang the Remote Unit into the upper bracket, insert it into the lower bracket, and fasten it to the lower bracket with the M8x25 screws (C), split lock washers (D) and washers (E), see chapter 3.1.3. The maximum diameter of the pole or column must not exceed 120 mm (4.7 inch). ax. 120 m figure 3-5 Pole mounting – max. diameter 3.1.5.
3. Commissioning figure 3-7 Pole mounting - pitches figure 3-8 Pole mounting - brackets figure 3-9 Pole mounting - fasten RU 1. Apply this procedure to both mounting brackets on both sides: Screw a hexagon nut (E) to the threaded bolt and place a flat washer (F)) on it. Insert this side of the bolt into the mounting bracket (A). Then, fasten the mounting bracket with a flat washer (F), split lock washer (G), and the locking nut (D). See figure 3-6 Pole mounting – with brackets. 2.
3. Commissioning 3.2. Electrical Installation 3.2.1. Health and Safety for Electrical Installation Read and observe chapter 1.2 Health and Safety. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 3.2.2. Property Damage Warnings for Electrical Installation 1.
3. Commissioning 3.2.3. Connections Alarm output connector Alarm input connector not required for operation Antenna connector Status LED Antenna connector AC Mains connector Opticalfiber connector Grounding bolt figure 3-10 Connector flange of ION-M7P/17EHP/19P, AC version MF0150A4A.
3. Commissioning Alarm output connector Alarm input connector Antenna connector not required for operation Status LED DC Mains connector Antenna connector Grounding bolts Opticalfiber connector figure 3-11 Connector flange of ION-M7P/17EHP/19P, DC version figure 3-12 DC Connector of ION-M7P/17EHP/19P Page 24 MF0150A4A.
3. Commissioning 3.2.4. Grounding (Earthing) The RU must be grounded (earthed). When double grounding lugs are used they must support M6 studs with a stud hole spacing of 15.88 mm (5/8”). 1. Connect an earth-bonding cable to one or both of the grounding bolt connections provided on the connector flange of the Remote Unit. Do not use the grounding connection to connect external devices. figure 3-13 Grounding bolts figure 3-14 Grounding bolt, schematic view 2.
3. Commissioning Attention: To minimize passive inter-modulation (PIM) distortion, attention has to be paid to the physical condition of the connector junctions: Do not use connectors that show signs of corrosion on the metal surface. Prevent the ingress of water or dirt into the connector. Use protective caps for the connectors when not mounted. Before mounting clean the connectors with dry compressed air.
3. Commissioning Warning: Flammable material. Risk of fire. Keep away from sources of ignition. Caution: Eye irritant product. Risk of eye irritation. Avoid contact with eyes and skin. Wear protective clothing, especially protective glasses. 4. Clean the connector winding with lintfree wipe drenched with isopropyl alcohol. 5. Clean the lip of the inner ring with a cotton bud drenched with isopropyl alcohol. 6. Clean the inside surface of the inner ring with a cotton bud drenched with isopropyl alcohol.
3. Commissioning 8. Clean in the similar way the connector of the connected cable. Remove protective caps from the unit connector first. 9. Remove metal chips and small particles from the mating and inner surfaces of the connector using compressed air. 10. Continue with the winding area using lint-free wipe drenched with isopropyl alcohol. 11. Continue with the inside mating surface of the inner ring. 12. Clean the outside surface of the center pin. Page 28 MF0150A4A.
3. Commissioning 3.2.7. Antenna Cable Connector Assembly The figures in this chapter illustrate the connection procedure and do not show the actual RU. 1. What is needed for the connector assembly? a. Torque wrench. b. (Adjustable) counter wrench 2. Join the connectors and turn the coupling nut until the thread grips. 3. Push in the connector until it clicks. 4. Fasten the coupling nut hand-tight. Do not turn the connector but the coupling nut only. MF0150A4A.
3. Commissioning 5. Retain the cable connector with the counter wrench and fasten the coupling nut with the torque wrench until the torque is applied (torque wrench clicks). Torque wrench For angled antenna connectors use your hand to retain the cable connector and fasten the coupling nut with the torque wrench. Make sure only the coupling nut is turned, not the cable connector. Counter wrench 3.2.8.
3. Commissioning Before connecting the fiber cables, follow the procedure below to ensure optimized performance. It is important for these procedures to be carried out with care: Remove fiber-optic protective caps. Do not bend the fiber-optic cable in a tight radius (<4 cm) as this may cause cable damage and interrupt transmission.
3. Commissioning 3.2.9. Protective Plug Connection A protective plug is provided for the connection of the fibre-optic cables. figure 3-15 Protective-plug assembly Note: Only high-quality connectors must be used for this type of plug. Qualified brands are Diamond or Huber & Suhner. For plug assembly, observe the following instruction: 1. Pass one or two contacts through the backshell and the clamp ring. 2.
3. Commissioning 5. Fasten the insulator by screwing the 6. Place the appropriate seal parts (with one groove for one contact or two backshell tight onto it. Use a spanner grooves for two contacts) over the with opening 32 to screw the cable(s) and push them into the backshell tight (no gap). backshell. No gap Seals with one groove 7.
3. Commissioning 3.2.10. Protective-Tube Kit As additional protection for the optical fibres, this connector type can be supplemented by a special tube kit. To fasten the tube correctly, first unscrew the clamp ring (if already installed) of the original plug kit.
3. Commissioning 3.2.11. Mains Power Connection Before connecting electrical power to the unit, the system must be grounded as described in chapter 3.2.4. Mains power must be connected at the mains connector of the unit. 3.2.11.1. Mains power connection AC 1. Take the Mains power cable that was delivered with the RU. 2. Locate or install a suitable power junction box or receptacle near the RU and route the power cable from the power source to the RU.
3. Commissioning The Mains cable is part of the delivery. It’s available in two wiring configurations: Prot ect ive Cap Pin 1 2 3 PE Wiring 1 Name Color Phase Black Neutral White n.c. n.c Ground Green Pin 1 2 3 PE Wiring 2 Name Color Phase Brown Neutral Blue n.c. n.c Ground Green/Yellow table 3-2 AC power cable pinning For the AC power supply connection, a minimum cross section of 1.5 mm2 is required.
3. Commissioning 3.2.11.2. Mains power connection DC Caution: Danger of electrical hazard by high current. Disconnect mains power before opening the DC connector housing. Note: The Mains cable must be properly secured observing local regulations and electrical codes. Be sure to allow enough slack in the cable at the RU to mount or dismount the cable into the DC Mains connector of the RU. Unscrew the two M3 x 12 captive screws and take off the cover from the DC Mains connector housing.
3. Commissioning First, install a conduit fitting (not contained in scope of delivery) to the 34.52 mm hole. This must be a suitable fitting for a 1 Inch conduit with lock nut. Inside, the clearance around the hole is 5 mm, the maximum space for the nut is 8 mm. Then, insert your wiring through the opening and mount it to the M6 mains terminals. Observe the correct polarity. Close the conduit fitting to ensure water tightness.
3. Commissioning 3.2.12. External Alarm Inputs and Outputs There are four alarm inputs and four alarm outputs. Each alarm output can be assigned individually to any alarm at the Remote Unit. Settings need to be made via the ION-M Master Controller. For details please refer to the corresponding chapter in the User’s Manual of the ION-M Master Controller.
3. Commissioning Alarm Outputs and +28V Output figure 3-21 Alarm outputs (optocoupler) figure 3-22 Flange connector, 7 poles The alarm outputs (pins 1 to 4: open collector output 5 V / 1 mA; see figure 3-22) are normally low. In case of an alarm they are high active (5 V). They can be used to monitor alarms with an external alarm indicator. The +28 V pin (pin 6&7) is specified to 28 VDC / 1 A and is protected by a thermoswitch.
3. Commissioning 3.2.13. Commisioning Flowchart Commissioning an ION-M Remote Unit Manual for Remote Unit Philips screwdriver Mounting kit Spanner, size 13 mm Drilling machine Dowels Screw driver Screw driver Spanner, size 13 mm Start Preperation Unpack RU, RU accessories and mounting kit. Mechanical installation Fasten wall or pole mounting kit to wall or pole. Mechanical installation Mount RU to mounting kit, ensure suffient air flow and avoid thermal short circuits.
3. Commissioning LED on? No Check power switch inside RU (RUs with door). Check mains cabling. Check mains power. Yes LED status Red Internal Error Change power supply (RUs with a door). Reduce environmental temperature. Eliminate thermal short circuit. Disconnect and connect mains. Fans should run. If not, replace the fans at RU. MU: Change amplifier setting at MU controller Orange Yellow LED status Yes Red Green Spare RU available? External error Close the door (RUs with a door).
4. Alarms and Troubleshooting 4. Alarms and Troubleshooting All alarms occurring can be checked via software at the Master Unit to where a message is transmitted when the software acknowledges a valid alarm. A new alarm message will not be repeated if the reason for the alarm is cleared or if the alarm continues. A new alarm message will be generated if the alarm is interrupted for at least five seconds after acknowledgement. Refer to the corresponding software documentation of the Master Unit for details.
5. Maintenance 5. Maintenance 5.1. General Read and observe chapter 1.2 Health and Safety. Caution: Rotating fans. Risk of injury in operation. Wear tight-fitting clothes and disconnect mains before connecting or replacing or cleaning the fan unit. Caution: The unit reaches high temperature in operation. Risk of burns by hot surface. Do not touch the unit before it has sufficiently cooled down. Note: Note: The Remote Unit does not require preventative maintenance measures.
5. Maintenance 5.2. Replacing the Fan Unit Replacement of the fan unit is not required as a preventative measure. Only if an alarm indicates a malfunctioning of a fan must the unit be exchanged. Note: Please observe that the fan unit can only be replaced as a whole. Do not remove the fans separately. Note: NEVER blow out the fan unit with compressed air. This would cause permanent damage to the unit. Read and observe chapter 1.2 Health and Safety as well as the instructions in section 5.
5. Maintenance 5.3. Cleaning the Heat Sink To avoid a malfunctioning of the Remote Unit, the heat sink should be cleaned in case of pollution. In order to prevent any damage, proceed as explained in the following. Note: Read and observe chapter 1.2 Health and Safety as well as the instructions in section 5.1 General before starting with the replacement procedure. Then, proceed as follows: 1. Switch off the Remote Unit.
6. Appendix 6. Appendix 6.1. Illustrations 176 824 Airf low 12.5 75 92 Power IN Cable R4 5m in. 150 Prot ect ive Tube Kit 21 R4 5 min . . min 21 00 R1 Cable bridge to Ext ension Unit figure 6-1 Cabinet drawing MF0150A4A.
6. Appendix 6.2. Specifications 6.2.1. SW Requirements Minimum Master Controller SW Package: with i-POI 17/17 (AWS-3) ION-M SW V7.20.0 without i-POI 17/17 ION-M SW V6.40.1 6.2.2. Electrical Specifications ION-M7P/17EHP/19P Electrical Mains power, nominal AC operating Power Mains power, nominal supply DC operating max.
6. Appendix 6.3. Spare Parts The following list contains all parts available for the Remote Unit. The configuration of the delivered unit meets the requirements of the customer and can differ depending on the state of the delivery. Maintenance of the RU should be performed on an FRU (Field Replaceable Unit) basis only. Do not damage the warranty labels on the components, as this voids the warranty.
7. Index 7. Index A H Alarms .................................................................... 43 External Inputs .................................................. 39 External Outputs................................................ 40 Inputs (external) ................................................ 39 List ..................................................................... 43 Outputs .............................................................. 39 Health and Safety .............................