Installation Instruction

ManualsBrandsAndrew Wireless System ManualsElectronicsION-M Remote Unit for cellular systems

The Remote Unit, Extension Unit or Master Unit must be

mounted by proffessionel / special trained installer.

1.1. MECHANICAL INSTALLATION

1.1.1. Health and Safety for Mechanical Installation

1. Caution: Risk of injury by the considerable weight of the unit falling. Ensure there is

adequate manpower to handle the weight of the system.

2. Caution: Risk of serious personal injury by equipment falling due to improper installation.

The installer must verify that the supporting surface will safely support the combined load

of the electronic equipment and all attached hardware and components. The screws and

dowels (wall anchors) used should also be appropriate for the structure of the supporting

wall.

1.1.2. Property Damage Warnings for Mechanical Installation

1. Attention: Do not install the unit in a way or at a place where the specifications outlined in

the Environmental and Safety Specifications leaflet of the supplier are not met.

2. Attention: Due to power dissipation, the Remote Unit may reach a very high temperature.

Ensure sufficient airflow for ventilation.

3. Notice: Exceeding the specified load limits may cause the loss of warranty.

4. Notice: When connecting and mounting the cables (RF, optical, mains, ...) ensure that no

water can penetrate into the unit through these cables.

5. Notice: Also observe all additional rules or restrictions regarding mounting that depend on

the type of Remote Unit. For details refer to section 7.2.2 Mechanical Specification. Install

the unit vertically with the fan unit at the top. A maximum tilt angle of 25° from a vertical

position must be kept, as in the following illustrations:

Summary of content (9 pages)

PAGE 1
Installation Instruction The Remote Unit, Extension Unit or Master Unit must be mounted by proffessionel / special trained installer. 1.1. 1.1.1. MECHANICAL INSTALLATION Health and Safety for Mechanical Installation 1. Caution: Risk of injury by the considerable weight of the unit falling. Ensure there is adequate manpower to handle the weight of the system. 2. Caution: Risk of serious personal injury by equipment falling due to improper installation.
PAGE 2
6. Notice: A spacing of 40 mm (1.58 inch) around the unit is required. 7. Notice: To ensure sufficient airflow when mounting the unit in enclosed spaces, two lid openings (one for the air inlet and the other for the air outlet) must be provided. Do not block these air inlets and outlets when mounting the Remote Unit. The size of each opening must equal at least 16 x 16 cm (>250 cm2). Ensure that there is no thermal short circuit between the air inlet and air outlet.
PAGE 3
1.2. 1.2.1. ELECTRICAL INSTALLATION Health and Safety for Electrical Installation Read and observe chapter 1.3 Health and Safety. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 1.2.2. Property Damage Warnings for Electrical Installation 1.
PAGE 4
1.3. HEALTH AND SAFETY 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 3. Caution: Laser radiation.
PAGE 5
8. Notice: Only license holders for the respective frequency range are allowed to operate this unit. 9. Notice: Make sure the repeater settings are correct for the intended use (refer to the manufacturer product information) and regulatory requirements are met. Do not carry out any modifications or fit any spare parts, which are not sold or recommended by the manufacturer. 1.5. COMPLIANCE 1.
PAGE 6
5. Notice: For installations which have to comply with FCC/ISED requirements: English: This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with Health Canada’s Safety Code.
PAGE 7
6. Notice: The unit complies with Overvoltage Category II. It also complies with the surge requirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local supply connection) and/or coarse protection (external surge protection) is recommended depending on the individual application in order to avoid damage caused by overcurrent. For Canada and US, components used to reduce the Overvoltage Category shall comply with the requirements of IEC 61643-series.
PAGE 8
Equipment Symbols Used / Compliance Please observe the meanings of the following symbols used in our equipment and the compliance warnings: Symbol Compliance --- FCC --- ISED CE CE Meaning / Warning For industrial (Part 20) signal booster: WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.
PAGE 9
Required Antenna Distances ION-M Model ION-M23 SDARS 3Sec. ION-M23 SDARS 1Sec. Antenna gain without cable loss [dBi] 9 9 Maximum Distance FCC ISED m inches m inches 0.355 13.97 ----0.596 23.46 ----- WEEE Recycling Country specific information about collection and recycling arrangements per the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations is available on CommScope’s website. http://www.commscope.