Installation Manual

Mounting Kits For Wide Panel Antennas

BSAMNT Series: Mounting systems for

installations (60-115mm pipe diameter) for heavy duty applications

cylindrical pipe

Installation Instructions

Andrew Institute offers installation training.

Bulletin 639825-1 • Revision B • March 2013

Page 1 of 2

WSHR,LK,SPLT,M12,STL,GALV

Pre-assembly of Downtilt Brackets

Top / Middle Mount Installations

(fully collapsed position)

Part Lists

• Bracket edges parallel to each other.

M10 bolt

M12 bolt

BOLT,CARRIAGE,M12 X 200,STL,GALV 4

M10 bolt

be configured in pre-assembly

position (fully collapsed).

9 108

CRITICAL: For initial installation

to pipe, downtilt brackets must

ITEM NO. DESCRIPTION QTY U/M

1 PIPECLAMP BRACKET, NO FLANGE 2 EA

2 PIPECLAMP BRACKET, SHORT FLANGES 2 EA

3 NOTCHED BRACKET 1 EA

4BRACKET 1 EA

5 SCR,HCS,HEX,M8X25,STL,GALV 4 EA

6 WSHR,LK,SPLT,M8,STL,GALV 4 EA

7 TWO HOLE PLATE, 8mm X 1.25 PITCH 2 EA

8 NUT,HEX,M10,STL,GALV 12 EA

9 WSHR,LK,SPLT,M10,STL,GALV 6 EA

10 SCR,HCS,HEX,M10X40,STL,GALV 6 EA

11 NUT,HEX,M12,STL,GALV 8 EA

12 WSHR,FLT,M12,13X28X2.5,STL,GALV 4 EA

MAXIMUM TORQUE

M8 15N.m (11ft.lbs)

M10 37N.m (27ft.lbs)

M12 58N.m (43ft.lbs)

ATTENTION: Insert M12 bolts and M12

flat washers into bracket with tabs

prior to attaching bracket to antenna.

two hole plate

M8 bolt

PAGE 1
Installation Instructions Mounting Kits For Wide Panel Antennas BSAMNT Series: Mounting systems for cylindrical pipe installations (60-115mm pipe diameter) for heavy duty applications ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DESCRIPTION PIPECLAMP BRACKET, NO FLANGE PIPECLAMP BRACKET, SHORT FLANGES NOTCHED BRACKET BRACKET SCR,HCS,HEX,M8X25,STL,GALV WSHR,LK,SPLT,M8,STL,GALV TWO HOLE PLATE, 8mm X 1.
PAGE 2
BSAMNT Mounting Kit CommScope Bulletin 639825-1 • Revision B • March 2013 Page 2 of 2 (Continued from page 1) MAXIMUM TORQUE M10 37N.m (27ft.lbs) M12 58N.m (43ft.lbs) M12 bolt 14 12 13 11 10 9 8 2 1 M10 bolt ATTENTION: Insert M12 bolts and M12 flat washers into bracket with tabs prior to attaching bracket to antenna. Bottom Mount Installation • Loosen pivot bolts . (do not remove) M10 pivot bolt (loosen only) M10 pivot bolt (loosen only) • Remove adjuster bolts.
PAGE 3
RF Safety Warning: Although the final configurations are determined at time of licensing, it is important that the antenna selection and installation do not exceed equipment authorization and adequate separation distance is maintained. One of investigated configurations is that RRH 2x45 MHz has an output EIRP of 5.2kW and a minimum RF safety separation distance of 6.4 meters with max gain 17.5 dBi.