andi be free® Vent Mount Wireless Charger for car EN Manual DE Bedienungsanleitung
Operating instructions Congratulations on the purchase of your andi be free® Vent Mount Charger. The Vent Mount Charger charges your smartphone in the car and holds it magnetically and attaches stably to the vent. The charger rotates for an optimal view of the display. Please make it easy for yourself and watch the video for assembly. Just scan the QR code and watch the instruction. Thank you very much for this.
Connecting the Charger • • • • • Remove the Vent Mount Charger from the package and connect the included USB C cable to the charger head. Inspect the andi be free® Wireless Vent Mount Charger, as well as all included accessories, for damage. A defective device must not be put into operation under any circumstances. Check if the mechanism [1] of the hook is compatible with your ventilation. The hook must fit through the fins.
• • • • • show the same number/ millimeter. The millimeters at the top and bottom should also be identical. Take the Sticky Pad and remove the protective film. Hold the Sticky Pad on the edge only so as not to transfer any dirt to the adhesive surface (this will affect the adhesive strength). Hold the template firmly with one hand and check again that the template is correctly seated. Stick the Sticky Pad into the round recess of the template on the smartphone.
USB cable must not be bent, pinched or pulled over sharp edges. The unused and unattended andi be free® device must be disconnected from the power supply if you are going to be absent for a long period of time. If you notice that the andi be free® product emits odor, smoke or noises, immediately turn off the power supply to the device (by operating the fuses of the power supply), then disconnect the device from the power supply and do not use it again.
Known to us and excluded are silicone cases and potential future smartphone models with special (dirt) repellent coatings. Holding power and wireless charging function are only given if: from whom you purchased the device, or 2) the andi be free® store under ‚Returns and Warranty‘ (www.wireless-charging.com) if you purchased the device there. 1. your smartphone has an integrated wireless charging function 2. your smartphone case is not more than 5mm thick 3.
resources. To return the used device, the local return and collection systems should be used or the dealer from whom the product was purchased should be contacted. The latter can also take back the product for environmentally friendly recycling. or incomplete installation of the andi be free® Wireless Vent Mount Charger or failure to observe the safety and usage instructions.
Bedienungsanleitung Herzlichen Glückwunsch zum Kauf deines andi be free® Vent Mount Chargers. Der Vent Mount Charger lädt dein Smartphone im Auto, hält es magnetisch und wird stabil an der Lüftung angebracht. Das Ladegerät ist schwenkbar und ermöglicht dadurch eine optimale Sicht auf das Display. Wie montiere ich den Vent Mount Charger? Im Montage-Video wird dir alles schnell und einfach gezeigt. Einfach den QR Code scannen und die Anleitung anschauen.
Anschliessen des Chargers • • • • • • Nimm den Vent Mount Charger aus der Verpackung und schliesse ihn an das beigelegte USB C Kabel an den Charger Kopf an. Überprüfe den andi be free® Wireless Vent Mount Charger, sowie sämtliches mitgeliefertes Zubehör auf Schadstellen. Ein defektes Gerät darf in keinem Fall in Betrieb genommen werden. Prüfen Sie, ob der Mechanismus des Hakens [1]mit deiner Lüftung kompatibel ist. Der Haken muss durch die Lamellen passen.
• • • • • • 18 ist darauf zu achten, dass die Millimeterangaben an den Rändern des Smartphones/Hülle abgelesen werden können Verschiebe die Schablone, bis die Millimeterangaben auf der rechten und linken Seite dieselbe Zahl/Millimeter anzeigt. Auch die Millimeter oben und unten müssen identisch sein. Nimm das Haft-Pad und entferne die Schutzfolie. Halte das Haft-Pad nur am Rand, um keine Verunreinigungen auf die Klebefläche zu übertragen (das beeinträchtigt die Haftkraft).
stecke den Netzstecker aus. Trage oder ziehe das andi be free Produkt nicht am USB-Kabel. Das USB-Kabel darf nicht geknickt, eingeklemmt oder über scharfe Kanten gezogen werden. Das unbenutzte und unbeaufsichtigte andi be free Gerät muss bei längerer Abwesenheit vom Stromnetz getrennt werden.
andi be free® Haft-Pad für Smartphone-Hülle und Smartphone Unser andi be free® Haft-Pad kleben auf den meisten Smartphone Modellen und Hüllen. Uns bekannt, und ausgenommen sind Silikonhüllen sowie potentielle zukünftige Smartphone Modelle mit Speziellen (Schmutz-) Abweisenden Beschichtungen. Haltekraft und Wireless Charging Funktion sind nur gegeben, wenn: 1. 2. 3. 4.
scheuernden oder aggressiven Reinigungsmittel, weil diese die Oberfläche beschädigen können. Entsorgung Nicht im Hausmüll entsorgen. Der Vent Mount Charger muss verantwortungsbewusst recycelt werden, um die nachhaltige Wiederverwendung von Ressourcen zu gewährleisten. Um das verwendete Gerät zurückzugeben, sollten die lokalen Rückgabe- und Sammelsysteme genutzt oder der Händler, bei dem das Produkt gekauft wurde, kontaktiert werden.
Kontakt Tecflower AG Glarnerstrasse 88 8854 Siebnen Schweiz www.wireless-charging.com patents pending design protection WIPO assigned EU represented by: get-e-right GmbH Schlossstr.
FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.