Power Window Control System Installation and Programming Guide Power Window Control System Installation and Programming Guide
Table of Contents Power Window Control System Window Preparation Existing Window or New Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-XX Power Window Control System Installation New Construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Existing Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-19 Power Window Control System Programming Console Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Window Control System Window Preparation Power Window Control System Window Preparation XX 000XXXX 3
Power Window Control System Installation Guide Power Window Control System Installation Guide for Andersen® Awning Windows with Power Windows for Andersen® Awning Windows with Power Windows Thank you for choosing Andersen. / Gracias por elegir Andersen. This document is under construction do not print, publish, or distribute For questions call 1-888-888-7020. For more information and/or guides visit a n d e r se n win d ows. co m. Please leave this guide with building owner.
Power Window Control System Installation (New Construction) Power Window Control System Installation (New Construction) ▶ See wiring diagram for proper wire configuration prior to starting ▶ See wiring diagram for proper wire configuration prior to starting XX 1 2 Interior Interior Install window following installation instructions. Install window following installation instructions. Drill 3/8" hole through side extension jamb as shown. Drill 3/8” hole through side extension jamb as shown.
5 Interior Side Jamb Side Jamb 18-3 Wire 18-3 Wire Run 18-3 wire to midpoint of window. Run 18-3 wire to midpoint of window. 14-2 (min.) Wire 14-2 (min.) Wire Run 18-3 wire through side jamb between power box and awning window(s) and run 14-2 (min.) wire to power box location. Run 18-3 wire through side jamb between power box and awning window(s) and run 14-2 (min.) wire to power box location. 6 Interior Pigtail Wire Pigtail Wire Plug pigtail wire into electric operator.
8 Do not over drive screws. Product damage may result. No ajuste demasiado los tornillos. El producto se puede dañar. Interior Fasten electric operator with four (4) screws. Fasten electric operator with four (4) screws. 9 Interior Strip pigtail wire ends and align same color wires with 18-3 wires and connect with wire nuts. Make sure wire color continuity is maintained. Strip pigtail wire ends and align same color wires with 18-3 wires and connect with wire nuts.
12 13 Interior Interior Route 18-3 wire through larger compartment Route 18-3 wire through larger compartment 6" Turn power off to this circuit. Failure to do so may result in personal injury. Turn power off to this circuit. Failure to do so may result in personal injury. Foam Packing Block Foam Packing Block Route 14-2(min) wire through smaller compartment. Route 14-2(min) wire through smaller compartment.
18 Tape Tape Interior Red Red Terminals Terminals Battery Battery Black Black Remove tape from battery terminals. Align and connect red and black leads to red and black battery terminals. Remove tape from battery terminals. Align and connect red and black leads to red and black battery terminals. 19 20 Interior Interior Tuck connected 18-3 wires into large compartment of power box and reapply faceplate, as shown.
23 Interior Fasten remodeling clip. Fasten remodeling clip. 24 Interior Keypad Keypad Wire Harness Wire Harness Keypad Connector pins Keypad Connector pins Fasten wire harness from power box to keypad connector pins. Fasten wire harness from power box to keypad connector pins. 25 26 Interior Interior Open keypad panel and fasten. Open keypad panel and fasten. Position keypad to mounting ring. Position keypad to mounting ring.
27 Interior Electric Operator Cover Electric Operator Cover LED Cover Lens LED Cover Lens Apply finish to electric operator cover and snap LED cover lens to cover as shown. Apply finish to electric operator cover and snap LED cover lens to cover as shown. 28 29 Interior Interior 29 Insect Screen Insect Screen Install insect screen. Insect screen must be in place for electric operator motor to operate. Install insect screen. Insect screen must be in place for electric operator motor to operate.
Power Window Control System Installation (Existing Construction) Power Window Control System Installation (Existing Construction) ▶ See wiring diagram for proper wire configuration prior to starting ▶ See wiring diagram for proper wire configuration prior to starting XX 1 2 Interior Interior Remove tape. Remove tape. Remove mounting ring and screws from power box. Remove mounting ring and screws from power box. 3 4 Interior Interior Remove attachment tab. Remove attachment tab.
5 6 Interior Interior 1-5/8" Drywall Screw 1-5/8" Drywall Screw Drywall Saw Drywall Saw Attach screw and cut drywall on traced line. Attach screw and cut drywall. Remove cut drywall. Remove cut drywall. 7 Interior Drill 3/8” hole through side extension jamb as shown. Drill 3/8” hole through side extension jamb as shown. 9 8 18-3 Wire 18-3 Wire Interior Side Jamb Side Jamb Run 18-3 wire to midpoint of window. Run 18-3 wire to midpoint of window. 14-2 (min.) Wire 14-2 (min.
9 Interior Pigtail Wire Pigtail Wire Plug pigtail wire into electric operator. Plug pigtail wire into electric operator. 10 Interior Position electric operator. Attach electric operator arms to sash bar. Position electric operator. Attach electric operator arms to sash bar. 11 Interior Measure and mark center of sill. Measure and mark center of sill.
12 Center of Electric Operator Center of Electric Operator Interior Kerf Kerf Pencil Mark Pencil Mark Position center of electric operator at marked line on sill with operator tabs in locating kerf. Position center of electric operator at marked line on sill with operator tabs in locating kerf. 13 Do not over drive screws. Product damage may result. No ajuste demasiado los tornillos. El producto se puede dañar. Interior Fasten electric operator with four (4) screws.
15 Interior 12v DC Grommet 12v DC Grommet 16 Face Plate Face Plate Interior 17 Interior 120v AC Grommet 120v AC Grommet Foam Packing Block Foam Packing Block Remove wiring access hole grommets. Remove wiring access hole grommets. Remove faceplate. Remove faceplate. 18 19 Interior Interior Remove foam packing block. Remove foam packing block. Turn power off to this circuit. Failure to do so may result in personal injury. Turn power off to this circuit.
22 23 24 Interior Interior Interior 18-3 Wire 18-3 Wire 14-2 (min.) Wire 14-2 (min.) Wire 14-2 (min.) Wire 14-2 (min.) Wire Align 14-2(min.) wires to black and white wires in smaller compartment of power box and connect with wire nuts. Align 14-2(min.) wires to black and white wires in smaller compartment of power box and connect with wire nuts. Strip wire ends. Strip wire ends. 25 26 Interior Interior Tuck connected 14-2(min.) wires into small compartment of power box, as shown.
28 Interior Keypad Keypad Wire Harness Wire Harness Keypad Connector pins Keypad Connector pins Fasten wire harness from power box to keypad connector pins. Fasten wire harness from power box to keypad connector pins. 29 30 Interior Interior Position keypad to mounting ring. Position keypad to mounting ring. Open keypad panel and fasten. Open keypad panel and fasten.
32 3 33 Interior Interior Insect Screen Insect Screen Install insect screen. Insect screen must be in place for electric operator motor to operate. Install insect screen. Insect screen must be in place for electric operator motor to operate. ▶ Power window control system installation in existing construction is complete. ▶ Power window control system installation in existing construction is complete. Insect Screen Sensor Insect Screen Sensor Rotate slightly and snap sill cover onto motor housing.
Power Window Control System Console and Remote Control Operation and Programing Power Window Control System Console and Remote Control Operation and Programing for Andersen® Awning Windows with Power Windows for Andersen® Awning Windows with Power Windows Thank you for choosing Andersen. / Gracias por elegir Andersen. This document is under construction do not print, publish, or distribute For questions call 1-888-888-7020. For more information and/or guides visit a n d e r se n win d ows. co m.
Power Window Control System Programming Procedure (Console) Power Window Control System Programming Procedure (Console) ▶ XXX ▶ XXX XX 1 If insect screen is not present, screen sensor must be depressed for electric operator motor to operate. If insect screen is not present, screen sensor must be depressed for electric operator motor to operate.
a 2 Selector Switch Selector Switch Move selector switch on key pad to “ON” position. Move selector switch on key pad to “ON” position. 3 Display Display 3X Program Button Program Button Insert paper clip into console’s program button location and hold until key pad LED blinks 3 times slowly and “E” is displayed on the screen. Insert paper clip into console’s program button location and hold until key pad LED blinks 3 times slowly and “E” is displayed on the screen.
Power Window Control System Programming Procedure (Remote Control) Power Window Control System Programming Procedure (Remote Control) ▶ XXX ▶ XXX 1 Move selector switch on console to the “OFF” position. Move selector switch on console to the “OFF” position. 2 3X Insert paper clip into program button location and hold until key pad LED blinks 3 times slowly and “H” is displayed on the LCD.
3 4 3X Move selector switch on remote control to the “ON” position. Move selector switch on remote control to the “ON” position. Insert paper clip into enrollment button location and hold until key pad LEDs blink 3 times slowly. Insert paper clip into enrollment button location and hold until key pad LEDs blink 3 times slowly. 5 3X 3X After short delay, both remote and console LEDs will blink 3 times quickly, and the remote will be programed to the console.
Power Window Control System Operation Power Window Control System Operation 1 Push ( U ) on numbered button on key pad to open window. Display will light and window will open until stop button is pushed or window is fully opened. Push and release ( V ) to close window. Push ( U ) on numbered button on key pad to open window. Display will light and window will open until stop button is pushed or window is fully opened. Push and release ( V ) to close window.
Power Window Control System Wiring Diagram Power Window Control System Wiring Diagram Daisy Chain Connection Operator 4 Operator 3 Operator 2 Operator 1 Star Connection Operator 4 Operator 3 Operator 2 Operator 1 Single Connection 000XXXX 26
Power Window Control System Operation Codes Power Window Control System Operation Codes Use these codes to help trouble shoot power window problems. Refer to the instruction guide for detailed installation and operation guidelines. Call Andersen at 1-888-888-7020 for further assistance. Use these codes to help trouble shoot power window problems. Refer to the instruction guide for detailed installation and operation guidelines. Call Andersen at 1-888-888-7020 for further assistance.
Power Window Control System Trouble Shooting Power Window Control System Trouble Shooting Issue/ Issue Power driver Does Not Operate - Open or Close Power driver Does Not Operate - Open or Close Power Operator Has Intermittent Opening/ Closing Power Operator Has Intermittent Opening/ Closing 000XXXX Things To Check / Things To Check 1) Make sure the screen is properly installed and red screen sensor is depressed. 1) Make sure the screen is properly installed and red screen sensor is depressed.
Trouble Shooting Continued/ Issue/ Issue Light on Driver Does Not Light Up Light on Driver Does Not Light Up Console Display Does Not Light Up Console Display Does Not Light Up Window Dirver System Sound Quality Changes Excessivly Window Dirver System Sound Quality Changes Excessivly Where Do I Find The Wiring Schematic Diagram? Where Do I Find The Wiring Schematic Diagram? 000XXXX Things To Check / Things To Check 1) Make sure the control panel, driver and remote are all adequately powered: - Correc
Trouble Shooting Continued/ Issue/ Issue Rain Sensor Is Not Working when rain or moisture is present Rain Sensor Is Not Working when rain or moisture is present Things To Check / Things To Check 1) Check cleanliness of both rain sensors - Use rag to remove debris from sensor(s) 1) Check cleanliness of both rain sensors - Use rag to remove debris from sensor(s) 2) Inspect both rain sensors for signs of damage 2) Inspect both rain sensors for signs of damage 3) Rain sensors will only work if override has
Regulatory Statements FCC and Industry Canada Changes or modifications not expressly approved by Andersen Corporation may void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
voluptam, simenim intibus. Aboreicat is erci beaque plabore mporpor rovidem evelenimus et poreped eoste id eum si ut eos nis et aut pratiatus ex eium ium explace archilibus. Limited Warranty POWER OPERATOR Olent lis et molest, expelig enditas cupisti bustentia vere voles estiassin consendem ut eic tem la quiatem. Ibeaquam, qui comnis porume as que pratem volore vent harum vel eatem. Nam quia dolorpos quibusam core mi, quiat.
