Installation & Assembly

ManualsBrandsAncona ManualsDrop-in Kitchen Sinks30" L x 19" W Double Basin Drop-In Kitchen Sink with Faucet

STANDARDS

ASME A112.18.1

CSA B125.1

NSF 61-9

LISTED IAPMO/cUPC

Gather the necessary tools as shown below to complete the installation of this

faucet. Some may not be needed depending on the model of faucet you are

installing. Check with your local hardware store on the requirements of your

installation situation.

Tools:

PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH

SAFETY GLASSES SCREW DRIVER

PLIERSCHANNEL LOCKS ADJUST ABLE WRENCH

SEALED-TUBE

HEX-KEY TAPE

Connect to water supply lines with either

A 3 8 O D copper tubing ball nose

risers with the coupling nuts or

B 3 8 copper tubing no ball with

supplied tube head interior connector or

C IPS faucet connectors 1 2

Tighten connection

with two wrench to

prevent damage to

tube body. Be

careful not to bend

the stem as this will

void the product

warranty.

A . B .

C .

Helpful Information

Flow Rate Chart

Important

Palermo

AN-4107

2015-09-25

MAAN4107-02

L/Min

Bar

Summary of content (6 pages)

PAGE 1
Helpful Information Tools: Gather the necessary tools as shown below to complete the installation of this faucet. Some may not be needed depending on the model of faucet you are installing. Check with your local hardware store on the requirements of your installation situation. Palermo AN-4107 PLUMBERS STANDARDS - SAFETY ASME A112.18.1 CSA B125.1 NSF 61-9 LISTED IAPMO/cUPC PUTTY FLASHLIGHT GLASSES CHANNEL SCREW DRIVER LOCKS ADJUST ABLE WRENCH HEX-KEY SEALED-TUBE Flow Rate Chart A. B. C.
PAGE 2
Installation size map Three Hole Installation Step 1: Repeat steps 1 and 2 from Single Hole Installation. Step 2: Insert plate before inserting faucet body into sink deck. Step 4: Ensure all connections are tightly set in place to avoid leakage. 19 1/4” (490 mm) 9 7/8” (252 mm) Test Faucet Installation A. Move handle into "OFF" position. B. Turn on water supplies. Check connections for leaks. C. Remove hand shower and let both hot and cold water run for one minute.
PAGE 3
Single Hole Installation WARNING Ensure hoses are tightly screwed into positon as they may move during transportation and installation. Step 1: Unscrew shank Hot/ Chaud Assurez-vous de bien serrer les embouts de chaque Tuyau car ils peuvent se dévisser lors du transport – bien valider après l’installation aussi Etape 1 : Dévisser la tige filletée.
PAGE 4
Information utile Outils: Réunissez les outils nécessaires comme montrés ci-dessous, pour compléter l'installation de ce robinet. Certains peuvent ne pas être requis, selon le modèle du robinet que vous installez. Vérifiez avec votre quincaillerie locale sur les exigences de votre situation d'installation. Palermo AN-4107 MASTIC DE PLOMBIER NORMES - LAMPE DE POCHE LUNETTES DE SÉCURITÉ ASME A112.18.1 CSA B125.
PAGE 5
Carte de dimension d'installation Étape 1: Répetez les étapes 1 et 2 de l’Installation à un orifice. Étape 2: Inserrez la plaque avant d’inserrer le robinet dans le comptoir. Étape 4: Afin d’assurez qu’il n’ya pas les fuites d’eau. 19 1/4” (490 mm) 9 7/8” (252 mm) Testez l'installation du robinet 2 1/16” (52 mm) Max 1 3/4” (45 mm) 18 11/16” (221 mm) Étape 3: Répetez les étapes 3 à 6 de l’Installation à un orifice. A. Déplacez la poignée vers le bas à la position “OFF“. B.
PAGE 6
Installation à un orifice WARNING Ensure hoses are tightly screwed into positon as they may move during transportation and installation. Step 1: Unscrew shank Hot/ Chaud Assurez-vous de bien serrer les embouts de chaque Tuyau car ils peuvent se dévisser lors du transport – bien valider après l’installation aussi Etape 1 : Dévisser la tige filletée.