Operation/Reference Guide Tango Amplifiers DAS-TAMP4-SIG Tango 4-Channel Amplifier DAS-TAMP8-SIG Tango 8-Channel Amplifier Tango Distributed Audio Last Revised: 2/10/2010
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1. Read instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS b Tango Amplifiers
Table of Contents Table of Contents IMPORTANT SAFETY INSTRUCTIONS ................................................................ a Tango Amplifiers ................................................................................................1 Overview .................................................................................................................. 1 Product Specifications ............................................................................................. 2 Rack Mounting ...
Table of Contents ii Tango Amplifiers
Tango Amplifiers Tango Amplifiers Overview Where more than one pair of speakers is required in Tango Distributed Audio zones, the Tango Amplifier (FIG. 1) provides the extra power needed to drive up to 4 additional speaker pairs per unit for a total of 12 additional speaker pairs or 24 channels per zone. Use Tango Amplifiers in backyards, large rooms or other zones where additional speakers are needed. FIG.
Tango Amplifiers Product Specifications Tango Amplifiers - Product Specifications Models Available: DAS-TAMP4-SIG 4-Channel Amplifier: • US version (120V) - FG1103-21 • Int’l version (240V) - FG1103-23 DAS-TAMP8-SIG 8-Channel Amplifier: • US version (120V) - FG1103-22 • Int’l version (240V) - FG1103-24 Dimensions (HWD): • 3 1/16” x 17” x 13 1/2” (7.68cm x 43.18cm x 33.52cm) • RU: 2 Weight: 25.75 lbs (11.
Wiring and Connections Wiring and Connections Overview - Speaker Wire Technology (SWT) Speaker Wire Technology (SWT) allows both data and audio signals to travel over the same four conductor wire. This remarkable technology removes the need for control wire since the control and audio signals are shared on the same wire. The reliability and simplicity of this system has been proven for years.
Wiring and Connections Cable Type The Tango Amplifier is cabled using standard 4-conductor speaker cable originating at the Tango Controller, passing through the Keypad, and terminating at the speaker location. AMX recommends using a bundled 4conductor 16-gauge stranded copper wire in a single continuous run.
Wiring and Connections Wiring Diagram - Single Amplifier FIG. 3 illustrates the connections from a Tango Audio Controller, and to SWT Speakers and Metreau (SWT) Keypad. Tango Audio Controller Tango Amplifier DAS-MET-6SRC Metreau 6-Source Audio Keypad FIG.
Wiring and Connections Wiring Diagram - Expanded Configuration FIG. 4 illustrates stacking up to three Tango Amplifiers units per zone, to allow up to 12 speaker pairs (24 channels) in a single zone: Tango Audio Controller DAS-MET-6SRC Metreau 6-Source Audio Keypad Note: Only one Keypad can be installed per zone Tango Amplifier #1 Tango Amplifier #2 Tango Amplifier #3 FIG.
Wiring and Connections Tango Amplifiers 9
2/10 ©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.
