I
Preface ©Copyright 2008 All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Lithium batteries can be dangerous. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Under no circumstances should the user attempt to disassemble the power supply. The power supply has no user-replaceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
EN 50371: 2002 EN 60950-1: 2001 REGULATORY STATEMENT (R&TTE / WLAN IEEE 802.11A/B/G & 802.11 A/G/N) European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the 2.4465-2.4835GHz frequency range and must be restricted to indoor use.
Table of Content Introducing Your Notebook ................................................................................. 2 Install the Battery Pack..................................................................................... 3 Connecting to a Power Source......................................................................... 3 Open the Display Panel .................................................................................... 5 Turning on Your Notebook Computer..........................
VII
1
INNTTRRO G YO NG CIIN K UC OK DU OO OD BO R NO EB UR TE OU OT Operating Environment You can use your computer under a wide range of environmental conditions. However, to ensure long use and continued high performance, consider the following factors when setting up your computer: Set the computer on a flat, stable surface. To prevent damage to the computer’s hard disk drive, avoid using the computer where it will be exposed to strong vibration.
Preparing your computer. Install the Battery Pack Connecting to a Power Source You can use the provided AC adapter to supply your computer with power from an AC wall outlet. Place the computer so that you have easy access to its rear panel. Plug the AC adapter’s connector into the DC-IN connector on the rear panel of the computer. Connect the power cord to the AC adapter and then to a wall outlet.
Do not use inferior extension cords as this may result in damage to your Notebook. An AC adapter is provided along with your Notebook. Do not use a different adapter to power the computer, and do not use the AC adapter to power other electrical devices. Try not to turn off or reset your Notebook while the hard disk is in use.
Open the Display Panel Turning on Your Notebook Computer 5
Learning the Parts Open View 1
1. CCD Camera The built-in camera allows picture taking, video recording or video conferencing. You can use the hotkey combination of Fn + Esc to open the web camera. 2. LCD Display Your Notebook computer is equipped with a replaceable color Liquid Crystal Display (LCD) screen that supports up to 1280*800. It functions the same as a desktop monitor. Use a soft cloth without chemical liquids (use plain water if necessary) to clean the display panel. 3.
7. TouchPad The dual-button TouchPad is located below the keyboard. The TouchPad is hardware-compatible with the IBM PS/2 mouse and software-compatible with the Microsoft mouse. 8. TouchPad Buttons The buttons below the TouchPad correspond to the left and right buttons on a standard mouse. Left View 1. DC IN Connector Plug the AC adapter into this connector. 2. USB 2.0 Port (X3) The Universal Serial Bus (USB2.
3. Microphone Jack The microphone jack (3.5-mm diameter) is where you connect a microphone. 4. Stereo Headphone The stereo headphone jack (3.5-mm diameter) is where you connect the headphones or external speakers. 5. Card Reader The slot is where PC Card is inserted. The system also supports MMC, MMC plus, SD, 3-1 card reader. Right View 1. CRT Port The 15-pin VGA analog port is for connecting the external CRT monitor or projector.
Rear View 1. Kensington Lock Keyhole Your computer includes a keyhole to be used with a standard Kensington lock. You can connect the Notebook lock to a large object with the Kensington lock to prevent theft of your Notebook. 2. Ethernet / LAN Port The port connects to a network hub via the RJ-45 cable and also conforms to 10/100/1000Base-TX transmission protocol.
Bottom View 1. Battery Release Latch Slide the battery latch to release the battery pack 2. Battery Pack The battery pack is a built-in power source for the notebook.
System Status Indicator 7
LED Graphic Symbol Indication The solid-state disk drive indicator blinks when data is written to or read from the disk drive. The battery charge indicator (LED) shows the status of the battery’s power as follows: ON: The battery is charging when AC power is connected. OFF: The battery is charged or completely drained. Blinking: Battery power is in low low condition and AC adaptor is not connected. When the built-in wireless LAN is enabled, this indicator lights.
+ LCD/CRT mode – Press the Fn + F3 combination keys in switching to LCD/CRT mode. + WLAN mode – Press the Fn + F4 combination keys to Enable/Disable the wireless mode. + Brightness Up – Press the Fn + 6 key to increase the brightness of your screen display + Brightness Down – Press the Fn + 5 key to decrease the brightness of your screen display + Volume Up – Press the Fn + 4 key to increase the volume of any audio or video files the system is playing.
+ Mute mode – Press the Fn + 2 key to mute the volume of any audio or video files the system is playing.
11
Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. We recommend you to use batteries that are approved by an authorized dealer. Try not to use the wrong battery for it would cause serious damage to your computer. Battery Low-Power Warning Low Battery Warning Low battery condition occurs when battery power is reduced to 10%. The red power LED indicator blinks.
When the battery is fully charged, the battery charge indicator becomes green. If system runs at heavy loading or in a high temperature environment, the battery may not be fully charged. Be sure is not running heavy application and the battery temperature is near the room temperature, you can then recharge the battery. Checking the Battery Level You can check the remaining battery power in the Windows battery status indicator, which is located at the lower right-hand corner of the task bar.
Read Section Protecting Your Notebook in the beginning of this manual for tips about how to maintain the battery pack. To achieve optimal battery performance, you may need to do a battery calibration at a 3-month interval. To do this: Fully charge the battery. Fully discharge the battery in idle mode till it shutdown. Fully charge the battery again. Using Windows Power Options Windows Power Management provides basic power saving features.
Suspend Mode Standby Suspend The system automatically enters this mode after a period of inactivity, which is set in the Power Schemes dialog box. In Standby mode, hardware devices, such as display panel and hard disk, are turned off to conserve energy.
Hibernate Suspend In this mode, all system data are saved in the hard disk before powering down. When this mode is activated, all system state and contents are saved to the hard disk drive after a period of inactivity defined by the user. Touchpad Your notebook touchpad is compatible with the PS/2 mouse. A device driver is not required for working with application software that supports PS/2 mouse operation.
Graphic Subsystem Your computer uses a high performance 8.9 inch WUXGA/WSXGA panel with high resolution and multi-million colors for comfortable viewing. Audio Subsystem Your computer’s audio subsystem is Sound Blaster Pro-compatible. Adjusting the Volume Manually To increase the volume, press the FN + 4 combination keys in front panel of the computer. To decrease the volume, press the FN + 3 combination keys in front panel of the computer.
18
CUUSSTTO R ER TE UT PU MP OM CO RC UR OU YO GY NG ZIIN MIIZ OM Using System Setup System Setup is used when changing the booting priority, system password or adding new devices. After turning on your computer, when the booting screen appears, press to enter the initial System Setup screen.
System Setup Menus Main Menu Configures the basic system environment Advanced Menu Configures OS and major chipset options of the system. Security Menu Configures system security options. Boot Menu Configures booting options.
F10 - Saves changes and exits System Setup Exit - Exits the current sub menu or opens the Exit menu. Configures the Password Setting the Supervisor Password This serve as a restriction of your system access to authorized users only. 1. Select the “Security” menu in the BIOS setup 2. On the “Set Supervisor Password” item, press . 3. Enter a password, press , re-enter the password for confirmation, and press again. 4.
Setting User Password A password can also be set for other users to use the system. Before you configure a user password, the supervisor password must have been configured. Other users can use the system with their user password but not access to the System Setup. It is only that the supervisor password is deactivate will also deactivates the user password. On the “Set User Password” item, press , and complete step 3 and 4 mentioned in “Configuring the Supervisor Password”.
Click on the “Display Settings”.
Click on the “Advanced Settings” to enter the “Generic PnP Monitor and Intel® Cantiga Express Chipset Family” window display.
Click on the “Graphic Properties”.
Display Devices Select the “Display Devices” to indicate the display connected to your system.
Display Settings Adjust the color quality, screen resolution and refresh rate of your display.
Color Correction Adjust the color rate of your display.
Hot Keys These are all the available hot keys as your default setting in executing some of the major functions. You can either add or change the available hot keys.
30
TROUBLE SHOOTING Your computer has been fully tested and complies with the system specifications before shipping. However, incorrect operations and/or mishandling may cause problems. This chapter provides a reference for identifying and correcting common hardware and software problems that you may encounter. When you encounter a problem, you should first try to go through the recommendations in this chapter.
Some software programs, which have not gone through rigorous coding and testing, may cause problems during your routine use. Consult the software vendor for problem solving. Legacy peripheral are not plug-and-play capable. You need to restart the system with these devices powered up and connected first. Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash. Be sure the Quick Key Lockout Switch on the bottom of the computer is not engaged; otherwise the quick keys will not work.
Hard Disk Problems The hard disk drive does not work or is not recognizable If you had just performed a hard disk upgrade, make sure the hard drive connector is not loose and the hard disk drive is also correctly seated. The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be re-installed as well. Check the hard disk indicator LED. When you access a file, the LED lamp should light up momentarily. The new HDD may be defective or is not compatible.
The hard disk takes longer to read a fileIf you have been using the drive for a period, the files may be fragmented. Go to [Start > Programs > Accessories > System Tools > Disk Defragmenter] to perform a disk defragmentation. This operation may take a while. Interrupt requests or problems with other hardware devices may have occupied the CPU and therefore slows down the system performance. The files are corrupted Run the Error-checking utility in Windows to check the HDD. Double-click My Computer.
Memory Problems The POST does not show an increased memory capacity when you have already installed additional memory Certain brands of memory module may not be compatible with your system. You should ask your vendor for a list of compatible DIMM. The memory module may be defective. Network Adapter/Ethernet Problems The Ethernet adapter does not work Go to [Start > Settings > Control Panel > System > Hardware > Device Manager].
A freeze on the system during program operation An error occurs during program currently being used. Solution: An error with the Windows OS. Reboot the system using the Power button. System Not Resuming Operation If the system will not resume operation after system operation has been suspended, check the following possible causes: Solution: The battery may either be defective, or discharge to a critically low level. To correct this problem, connect an external power supply such as AC adapter.
Wireless LAN connection is disconnected after 2~3 minutes, and the connection is not recovered. Solution: The reason may be caused by channel interference, change the channel of the AP and reconnect. The computer is unable to connect to the Internet. Solution: Account for Internet service provider (ISP) is not properly configured. Ask for your ISP assistance. The Wireless LAN is connected, but I can not connect to or to another computer. Solution: Check the device driver is properly installed.
are using. What messages, if any, are on the screen? What software were you running at the time? What have you done already to try to solve the problem? If you have overlooked a step, your dealer may be able to solve the problem over the phone. The system could not resume after it enter the Standby mode Solution: Standby Mode – allows the computer or program save into the RAM. The system will enter the saving mode.
temperature reach the room temperature. After charging, the indicator will display 95~99% still uncharged Solution: The battery has the tendency to fully automatically discharged, once the battery is charged it will lower its capacity. When the system will automatically charged upon it reaches 94% capacity, this is a normal condition in protecting the battery.
40
SPPEECCIIFFIICCAATTIIO S NS ON CPU Intel® Diamonville platform, 400/533 MHz FSB, 512kB L2 Cache (1.6G) 2.5Watts CHIPSETS Core Logic: 945GSE 3.5W-6W + ICH-7 1.1Watts MEMORY 1x DDRII SODIMM 533M 256MB - 1024MB Maximum VGA 945GSE ultra low power Integrated 3D graphics AUDIO High Definition Audio BIOS INCLUDES SYSTEM & VIDEO Boot from USB Plug & Play APM 1.2 ACPI 2.
Card Reader - SD/MMC Card slot DISPLAY RESOLUTION CHANGE ZOOM function for 1024x600 as default LCD DISPLAY 8.9" 1024X600 WSVGA LCD, 210 nits CAMERA 0.3~1.3M CCD module (Option) 1.3M --> Z high 5.4m 0.3M --> Z high 5.4mm AUDIO Built in Stereo Speaker * 2 Built in Analog micro phone *1 Stereo Head Phone (3.5 mm) COMMUNICATION Wireless 802.11 b/g (Mini PCIe) ANTENNA 1 x Wireless LAN b/g I/O 1 x Stereo Headphone (3.5 mm) 1 x Stereo Microphone (3.5 mm) 1 x RJ-45 connector 1 x CRT port 3 x 4-pin USB 2.
BUTTON Power Button Functional short cut key Touch pad with Left/Right Button LED INDICATOR 1 X HDD Active 1 X Battery Status 1 X Wireless activity AC/DC ADAPTER Miniature Size Compact Adapter type (AC Plug on Power Brick) - US AC 100~240Volt / DC 12V 3A 36W(LC89) BATTERY PACK 1 Removable Battery Pack BATTERY CHARGE Smart Charger COLOR Yellow-Black, White, Black. DIMENSION 233.5X177.3X26.4-34.
Gift Box REGULATORY APPROVAL EMC - CE/FCC/ BSMI/VCCI Safety - UL/TUV/CB/CCC RF - FCC ID,CE,TELEC,DGT,SRRC WHQL - Windows XP Home 44
