DSR - 301 ACE User Guide
INFORMATION TO THE USER INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONTENTS For Your Safety 1. Before Getting Started 1.1 Main Features 1 1 1.2 Accessories 2 2. Controls and Functions 2.1 Front Pannel 3 3 2.2 Rear Pannel 4 2.3 Remote Control Unit 5 3. Connections 3.1 Connecting to the TV, VCR and Satellite Antenna 7 7 3.2 Connecting to the TV, HiFi system and 0/12V switch 8 3.3 Connecting DiSEqC switch 8 3.4 Connecting CA Module 9 4. Settings and Operations 4.1 Basic Settings 10 10 4.2 Viewing TV(or Radio) 13 4.3 Other functions 17 4.
Before Getting Started 1.1 Main Features Easy Menu Function TV Guide Function RF Output Function Electronic Program Guide(EPG) for On Screen Channel Information Software Upgrading Function Through RS-232C Cable by PC Perfect DiSEqC 1.
Accessories 1.
CONTROLS AND FUNCTIONS 2.1 Front pannel STANDBY ON Turn the power on/off. MENU Shows the menu application. Channel Change channel, move menu, or input frequency value. Volume Control volume, change item on menu or input frequency value. OK Select menu or value on menu item. CI Slot Insert CI module into CI slot.
Rear pannel 2.2 Rear pannel DIGITAL It receives signals from the LNB in the range of 950 ~ 2150MHz. Connect a satellite dish to DIGITAL. OUT It sends signal to the another receiver. RS-232C It receives data by connecting to PC for software upgrading. Connect with RS-232C cable a PC and receiver. AUDIO It provides stereo audio output. Connect the audio on TV to AUDIO with RCA cable. VIDEO It provides composite video output. Connect the Video on TV to VIDEO with RCA cable.
CONTROLS AND FUNCTIONS 2.3 Remote Control Unit Open the controller cover on the back and insert two batteries (AA - 1.5V). POWER Turn the power on/off. TV/SAT Select between TV Channels and Satellite channels for RF output. Numeric(0~9) Move menu, change channel or input frequency value. CLEAR Clear wrong number input or delete channel from TV (Radio) list or favorite channel list. MUTE Deactivate current sound. MENU Shows the menu application. EXIT Exit from the menu.
Remote Control Unit PROGRAM GUIDE Shows the broadcasting information.(Video - Audio - LNB) INFORMATION Shows the information of current channel. Click the INFO button twice, TELETEXT mode will be displayed. FAVORITE Add TV or Radio channel to the favorite list on Edit TV(Radio) Channels, or watch favorite channel from your favorite list. TV Change to TV mode from radio channel. RADIO It is for fast change to radio mode from TV channel. Shows the current Radio program list.
Connections 3.1 Connecting to the TV, VCR and Satellite Antenna It is not necessary to adjust power, as the product is of free - voltage (100 ~ 240V ) 1. Connect the RF cable from the TV OUTPUT on the satellite receiver to a TV and connect the RF modulate on the VCR and the TV ANT.IN. 3. Connect an antenna to the LNB socket on the VCR or other receiver and cable of the satellite dish to the DIGITAL on the satellite receiver.
Connecting to the TV 3.2 Connecting to the TV, HiFi system and 0/12V switch 1. Connect the RCA cable from the VIDEO INPUT on the TV to the VIDEO on the satellite receiver. 2. To use 0/12V switch, connect one cable of the 0/12V switch to the 0/12V on the satellite switch and connect another cable to the DIGITAL on the satellite receiver. 3. Connect a RF stereo cable from the AUDIO RL on the satellite receiver to the AUDIO RL on the HiFi system. 3.
Connections 3.4 Connecting CA module To receive the distrivuted program of Service Provider you need a Smart card or CI module. 1. Insert CI module fully into the CI slot for watching TV programmes from Service Provider. 2. Insert your card fully into the slot on the CI module, so that the microchip(the yellow spot) faces upwards and inwards.
Settings and Operations 4.1 Basic Settings If it is the first time using a receiver, you should set parameters for system configuration. Refer to the following section. 1. Turn on your TV and Satellite receiver. 2. Press the MENU button, main menu screen will appear as shown below. 1. Select Installation on the Main Menu. 2. Select LNB Power. 3. If LNB Power is independently supplied from outside source, set the LNB Power OFF. Otherwise set it ON. 4.
DisEqC 1.2 Limit Settings If you have a DiSEqC 1.2 motoried system to control your satellite antenna you have to make the following setting. First, you must select ON on DiSEqC 1.2 of LNB Setting in the TP Configuration. < Please refer to the TP Configuration section > 1. Select DiSEqC 1.2 Limit Settings of the installation. 2. You should set the East Limit and West Limit of your satellite antenna If you use the satellite receiver at first.
Settings and Operations You have to know valid value for your LNB at first. 1. Select TP Configuration of the installation. 2. Select correct name of Satellite. If there is no proper satellite name listed in the item, select one from any of USER1 ~ USER 19. 3. To change value of LNB from each satellite, press OK button from LNB. < Standard > < Universal > 4. For universal type of LNB, select Universal from LNB Type item and input the LNB frequency value on L.O.Freq. and L.O.Freq.
TP Configuration 7. Move to desired TP with CH on the RCU. If there are no transponder data which you want, move to Add and press OK button. 8. Select the desired satellite. And input correct values of Frequency, Polarization and Symbol Rate. Select the Polarization value as Hor or Ver. If you did not know accurate polarization value select Auto. Note You should find the correct data from satellite magazine or internet(http://www.SATCODX.com). 9.
Settings and Operations 12. In case of searching a certain satellite which can not be searched by TP Search, add channels by PID. Select Add Channel and input proper Channel name and input the values of Video PID, Audio PID and PCR PID. Then, press OK button from the Add item.
Viewing TV 4.2 Viewing TV(or Radio) 1. Press the Power button. 2. Press the TV(or Radio) button. 3. If you want to see all TV channel list, click the MENU button and then select the TV Channels(or Radio Channels). TV Channels(or Radio Channels) window will appear. Click the , you will see current Satellite name box. Select any satellite in the satellite name box, only the TV list of selected satellite will be displayed. VOL Viewing Favorite Channel 1. Press FAV key. 2. Select a CH .
Settings and Operations Edit TV Channels / Edit Radio Channels From these menus you can creat and edit channel list. Press OK button from Edit TV Channels and similar screen will be shown as below. Arrange channel To change the channel orders from TV List, press OK button from your desired channel. Then you should move to desired number by pressing CH , after then press OK button. Its orders will be changed.
Lock Channels Sort If you want to sort channels in order, select the SORT button in Edit channels. You can select the order you want. Lock Channels From here you can lock channels in any of the lists in order to prevent your children from watching. If you have the password already and want to lock a certain channel, press F.BK button at the desired channel. Everytime you watch the channel, the unit will ask you to input password. Edit Channel Name 1. Press INFO button on Edit TV or Edit Radio list.
Settings and Operations Parental Control If you use this funciton you have to enter the password everytime you start this satellite receiver. 1. Select Parental Control on the installation. 2. To secure program setting and installation, select Change Password. 3. Input 4 digits New Password. And input password Confirm New once more. After all the password function is set, the unit will ask you to input password to get into the menus of Installation and System Settings.
Other Functions 4.3 Other functions Audio Selection If broadcasting channel is supporting multi language, different language can be selected from Audio Selection. 1. To select different language on current channel, select Audio Selection on the Main Menu. 2. Press OK button on your favorite language. According to different audio data on each channel, up to 4 different audio language types can be selected. TV Guide Press GUIDE button of RCU for channel information. This function works in digital mode only.
Settings and Operations From Teletext Screen CLEAR Overlay background screen and teletext mode according to the following order(transparency - Teletext only - Opacity) INFO Hold of current Teletext page PAGE UP/DOWN Move previous and next page in one CH UP/DOWN Move previous and next page in one FAV/TV/RADIO/F.
System Settings 4.4 System Settings Please make sure to press OK button always, after the changing items of System Settings. Audio language Only if a current channel contains 2 or more audio language information, set the Audio Language as English or other favorite language. Then press OK button for its confirmation. Menu Language For menu language selection, select desired language from Menu Language of system Settings. Audio mode Select desired audio mode among Stereo, Main or Sub.
Settings and Operations TV Standard Except for a few, most countires are using PAL system for TV signal, accordingly set TV Standard as PAL. To be more flexible for NTSC or PAL signal from different satellites, select MULTI for automatic signal conversion. Then press OK button for its confirmation. RF mode If the satellite receiver is connected to the TV with a RF cable, you have to set the RF mode, which is dependent on the country where the satellite is being used. 1.
System Settings S/W Version Show software version. Select S/W Version. Initialization Press OK button from Initialization. If you want initialization, select OK button, otherwise, select any button of remote controller. The receiver will be turned off and on automatically after 1~2 seconds to initialize all the values to factory setting mode. As this procedure will clear and set to factory default values, end users are not recommended to operate this function. 4.
Appendix 5.1 Troubleshooting SYMPTOM SOLUTION No picture display and no LCD channel display Check the power connection No picture display with normal LCD channel display 1. Check the connection with TV 2. Check the connection between TV outside input and receiver cable 1. Check the LNB, Frequency, Polarization and Symbol Rate from Installation menu 2. Check the connection of receiver or Antenna angle 1. Check between sound output connector and TV 2.
Glossary 5.3 Glossary LNB Low Noise Block converter. The LNB is an electronic unit mounted on satellite dish to receive signals reflected by the dish and convert to signals. L.O. frequency Local Oscillator frequency as a part of LNB. It converts the satellite frequency to usable signals for the receiver. Polarization Polarization allows several programs to be fitted into same frequency band.
Appendix NTSC National Television Standards Committee PAL Phase Alternate Line Ku band 11~18GHz Frequency C band 3~4GHz Frequency SCPC Single Channel Per Carrier MCPC Multi Channel Per Carrier PID Packet Identifier. TP TransPonder SCART, RCA A connector for connection of Satellite receiver, VCR and TV sets. VCR Video Cassette Recorder.
