COPYRIGHT Copyright © 2012 Amroad Technology Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form or by any means without the express written permission of Amroad Technology Inc. To obtain consent, write to the attention of Amroad Technology Inc. Document No. DP100-25 2012-0716 www.amroad.com.tw DISCLAIMER Amroad reserves the right to change product specification without prior notice.
CONTENTS Contents COPYRIGHT ................................................................................................................................................................................................... II CONTENTS ............................................................................................................................................................................................... I CHAPTER 1 : INTRODUCTION .......................................................
CONTENTS 2. Connect the DC wires and Ethernet Cable. ...................................................................................................................................... 14 3. Install Video Door Phone into the Mounting Box. ............................................................................................................................ 15 CHAPTER 4 : CONFIGURING VIDEO DOOR PHONE.................................................................................................
CONTENTS Electronic Lock .............................................................................................................................................................................................. 45 Electronic Bolt ............................................................................................................................................................................................... 45 Wiring Connection and Web Page Setup ............................................
DP100-25 VIDEO DOOR PHONE Chapter 1 : Introduction Welcome Thank you for choosing this Video Door Phone. This DP100-25 is designed to co-work with IP Video Phone to compose a SIP based door entry system. Besides taking advantages of IP technologies, this system also can fully utilize the SIP protocol to link to your SIP VoIP services. In other words, this system performs not only as an Intercom system, but also work with your SIP-based community system.
DP100-25 SI MANUAL General Application of Door Entry System There are two major models of Video Door Phone: one is single unit model, the other is community model. They are applied on different conditions. Please see following descriptions: Villa Application DP100-25 is designed for building, apartment or community. It is also used for single house or villa. Please see Figure 2. Using a home IP PBX to connect all SIP-based devices. Communicate with each device simply with extension numbers.
DP100-25 VIDEO DOOR PHONE with a large IP PBX. Residents can check visitors, monitor public areas or call each others with extension numbers. Connect to SIP VoIP services via Internet. Figure 3: Community Application Amroad Technology Inc.
DP100-25 SI MANUAL Use of SIP SIP, initial of Session-Initiation-Protocol, it is an application-layer control (signaling) protocol for creating, modifying, and terminating sessions with one or more participants. These sessions include Internet telephone calls, multimedia distribution, and multimedia conferences.
DP100-25 VIDEO DOOR PHONE Chapter 2 : Knowing Video Door Phone Package Contents The following items are included in your Video Door Phone package. Check this list before installation to ensure that you have received all items. n Video Door Phone Unit o Wall Mounting Box p Terminal Connectors q Screw Pack (4 pieces of M6 x 20mm) \ Wrench ] Screw for Earth Wire ^ Wall mounted screw pack _ H-type Terminal Connector for Power Wire ` Cord End Terminal (12 pieces) a Plastic Protective Cover Master RFID Card Qui
DP100-25 SI MANUAL 6 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Front Panel Figure 6: Front Panel Amroad Technology Inc.
DP100-25 SI MANUAL LED Light There are IR LEDs on both sides of CMOS lens for light compensation. Blue LEDs are behind the keypads, and LCD screen is with blue backlight. The LED and blue backlight will light when any button/keypad is pressed. And, the LED and backlight can be set through WEB UI. LED WEB UI SETTING DESCRIPTION Sleep Mode Disable The blue LED will light On when any keypad is pressed. And, the keypad LED will be turned off in 5~10 seconds after phone call is ended.
DP100-25 VIDEO DOOR PHONE Rear Panel Figure 7: Rear Panel and Connectors Amroad Technology Inc.
DP100-25 SI MANUAL Reset Button The default IP type setting of Video Door Phone is “DHCP Client “. 1. Pressing the reset button for 3 seconds=>DP100-25 will turn into Statics IP mode as "192.168.0.50" and reboot by itself. 2. Pressing for over 6 seconds and Green LED ON=>Turn to DHCP mode as the default value and reboot by itself (Restore to factory setting). VOID Sticker There is a “VOID” sticker on the rear side of the DP100-25.
DP100-25 VIDEO DOOR PHONE Dimensions Figure 9: Dimensions Amroad Technology Inc.
DP100-25 SI MANUAL Chapter 3 : Installing Video Door Phone Suggested Installation Positions Due to the view angle of the camera lens is limited, to install the Video Door Phone in a correct position to get better view is very important. Suggested height of the lens position is at the height of 155 cm according to building conditions. And, the distance from the bottom of wall box to the ground is 123.5 cm. View angle of this door phone is 105O. Please see an example of installation position on Figure 10.
DP100-25 VIDEO DOOR PHONE Installing Procedures 1. Insert the Wall Mounting Box into the Wall. Cutting a hole that is able to contain the Wall Mounting Box and prepare the DC +12V and Ethernet cable ready. Then insert the box into the wall and pull the DC wires and Ethernet cable through the hole on the box. You must place the Box very precisely in horizontal in order to keep the Video Door Phone in correct position. Figure 11: Installing the Wall Mounting Box Amroad Technology Inc.
DP100-25 SI MANUAL 2. Connect the DC wires and Ethernet Cable. Connect the DC wire of DP100-25 to H-type power connector, and connect Ethernet cable to DP100-25 according to below Figure 12. Please be careful when you are connecting the DC +12V, be sure to check the DC condition before you start to connect the wires. Please screw the earth cable to the “Wall Mounting Box “. Figure 12: Connecting Cable & Wires 14 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE 3. Install Video Door Phone into the Mounting Box. After properly connecting the wires and cables, insert the Video Door Phone into wall mounting Box carefully. Then screw the 4 screws that come with the package into the front panel. Please double check all the installation procedure again, and you may power on and start the configuration procedures. Figure 13: Insert the Video Door Phone Amroad Technology Inc.
DP100-25 SI MANUAL NOTE: We suggest that the protective cover should be attached to DP100-25 and should not be torn up after DP100-25 installation. Do not tear up the protective blister until residents of community/building begin to use DP100-25 Video Door Phone. Figure 14: Don’t remove Protective Cover 16 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Chapter 4 : Configuring Video Door Phone Finding Video Door Phone on Networks This chapter describes how to configure your Video Door Phone via Web User Interface. Before proceeding configuration, you have to locate the Video Door Phone on the network. You may find out the IP address of this device on the LCD display. NOTE: By pressing “#” key on front panel, you will see IP address like on Figure 16. IP A d d re s s 10 .3 .1 .
DP100-25 SI MANUAL NOTE:1. While configuring WEB UI (User Interface), please do not operate this product so as to prevent this product from being out of order. 2. Do not input special symbols “, \, and & in the fields on the WEB UI. Otherwise, you will fail to save your setting normally. 3. After configuring some Web pages and pressing “SAVE” button, you need to wait a little longer for system to save the configuration. 20 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE System - Basic Settings Item Description Device ID This ID is a unique number that assigned by manufacturer. Date & Time Here shows date and time set on this phone. Set New Time and Date These fields allow user to set correct date and time according to the local–standard. You may synchronize phone time to match your PC by pressing “Sync with PC” button. Time Zone This field allows you to select your time zone to fit your location.
DP100-25 SI MANUAL Number” in Web “Extension number” page in advance. Back Light Open Select “On” to turn on the Back Light of the LCD always. Select “Off” to turn on the Back Light when any keypad is pressed. Language This feature allows you to select the display language on the LCD screen. Select “English” or “Traditional Chinese” Reboot Password This feature allows you to reboot the DP100-25.
DP100-25 VIDEO DOOR PHONE System – Network Settings Item Description MAC Address This is a quasi-unique identifier attached to most network adapters. IP Type The default value is DHCP Client. There are two options: DHCP Client and Static IP. A. DHCP Client: The system will automatically assign you an IP address. B. Static IP: you have to input IP address, Subnet Mask, Default Gateway, Primary DNS and Secondary DNS data. Save Amroad Technology Inc. Click this button to save your setting.
DP100-25 SI MANUAL System Login Name The default ID and password for system login are admin and admin. User may change his Login ID and Password on the webpage by entering new Login ID and Password. Figure 19: System Login ID Settings System Reboot When user needs to reboot DP100-25 remotely, just click “Reboot” button on this webpage to start this action. After confirm rebooting, Web User Interface will back to the home page, but the video door phone may take 30~60 seconds to restart its system.
DP100-25 VIDEO DOOR PHONE Phone Settings – Video You may set change the video settings in this page. ITEM Description Bandwidth You may select preferred bandwidth for video and audio streaming. There are 4 options: 128Kbps, 256Kbps, 384Kbps, and 512Kbps. Please check which bandwidth is suitable for you with your service provider. Codec Priority You may select priority of video codec here: H.263 – will authenticate H.
DP100-25 SI MANUAL z Save Orange Lamps – This condition is suited for indoor orange color or more red color environments. Click this button to save your setting. : “Turn on/off IR LED” and “adjust the brightness of CMOS” via Amroad IP Video phone, DP100-25 can’t get the correct value of the CMOS brightness in some environment, please adjust the brightness value via the Amroad IP Video Phone by pressing “2”(brighter) or “8”(darker) in conversation state. 26 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Phone Settings – Audio ITEM Description Code Priority You may select the Audio streaming priority – G.711. Scene You may select the AEC (Acoustic Echo Control) scene according the environment of the installed location. Select “Disable”, ”Default” or “User Define”. Figure 22: Audio Setting When “User Define” is selected, the following two items appears: Noise Threshold (db): Default: -40. The voice intensity that is lower than the value (-40db) will be neglected.
DP100-25 SI MANUAL 28 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE SIP Services You may setup advanced SIP service parameters in this page: Item Description Authentication Display Name This name will show on the IP phones of called parties. You can fill in the preferred name here. For example, Doorphone NOTE: Please enter Doorphone in the field of Display Name. When the Door Bell is pressed, there will be “Preview” function and Doorbell sound on Amroad IP Video Phone/Video Indoor Station.
DP100-25 SI MANUAL select Disable in the dropdown menu. And, fill in each other’s IP address. IP Address You may fill in the IP address of SIP Proxy Server in this field. SIP Registrar Server ITEM Description IP Address You may fill in the IP address of SIP Registrar Server here. Registration Expire Time Set the time for SIP registration authorization The default is 3600 seconds.
DP100-25 VIDEO DOOR PHONE Entrance Settings – Extensions You may configure call services in this page: ITEM Description Mapping Number Select “Enable” to allow you use a real house number instead of extension number assigned from IP PBX. For large community, it is easier for visitors to enter the real house numbers than extension numbers. Save Click this button to save your setting. Select Mapping File Once you enable the Mapping Number feature, you may import the mapping table from this field.
DP100-25 SI MANUAL #5,105,105-1F,0 #6,106,106-1F,0 #7,107,107-1F, 0 #8,108,108-1F, 0 0,1000,The Operator,1 1202,1001,First St No120 3F,2 1203,1002,First St No.120 4F,3 1204,0282265688,Outbond Call,4 Where “blue” part is necessary for the file, please add your mapping number in their following. The title of each column must be exactly same as above sample, hereunder are explanations of each column title: “name” – This column is the number that you wish visitors to input on the Video Door Phone keypad.
DP100-25 VIDEO DOOR PHONE After selecting the CSV file, you can press “Upload” button to start the uploading. Export Mapping File This item allows you to export existing mapping file (*.CSV) from DP100-25. The exported mapping file may be a good example for you. Press “Export” button to start exporting existing mapping file and save on your computer. Amroad Technology Inc.
DP100-25 SI MANUAL Entrance Settings – GPIO You may configure GPIO in this page: ITEM Description Device Relay Output Select “Positive” or “Negative” to connect to Positive (Electronic Bolt) or Negative (Electronic Strike) - triggered Electronic Door Lock. Press “#” to unlock by Press the “#” key a few seconds from your Amroad IP Video Phone or Video Indoor Station can trigger the function during answering the phone call. You can select the timer here.
DP100-25 VIDEO DOOR PHONE Entrance Settings –RFID You may get the related RFID information and delete the issued RFID Cards here. ITEM Description Master Card The master RFID card can issue new cards for new tenants. This field will display the card number of the Master RFID Card. By default, this field is null. Scan a new RFID Card for the first time, and it will be set as Master RFID Card.
DP100-25 SI MANUAL The item Erase RFID Number will appear. Then, you may input the specific issued RFID card number to delete it. 36 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Upgrade – Firmware Update The Upgrade function allows you to upgrade firmware of the DP100-25. The ways to upgrade the firmware are via Web UI. Item Description Hardware Version This field is to show firmware version number. Software Version This field is to show current firmware version number. Language This field displays the Language Pack. Select Application Pack Press “Browse” button and select Application Pack from your local disk.
DP100-25 SI MANUAL RFID Module Version This field displays the version of the RFID Module. Press the Restore Default button and wait for system to restore its original factory default Restore Factory Default setting. 38 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Configurations Item Description Import File User may press Browse button to select the location of the configuration file to import, which you may previously save to a local directory through the Export File option. Upload After selecting the configuration file, you can press Upload button to start the importing. Figure 28: Configuration Export File You can also use Export File to back up DP100-25 settings on your computer.
DP100-25 SI MANUAL AR APS This webpage allows manufacturing factory to perform management function through APS (Auto Provision Server). Figure 29: Auto Provision Server Item Description APS Server: This allows you to upgrade firmware of DP100-25 through network. For example, APS Server: https://rc.amroad.com.tw/aps/TaServlet/doorphone.php Save Click this button to save your setting. 40 Amroad Technology Inc.
DP100-25 VIDEO DOOR PHONE Chapter 5 : Using Video Door Phone Making Calls From Video Door Phone Welcome! Using the Video Door Phone is quite simple. You will see “Welcome!” on and turn off the LCD display when the system is ready. Please follow these few steps to call the party that you wish to call: OK 1. Key in the extension number of the called party. Usually you will see an extension table beside this Video Door Phone: Extension Name 1001 Smith Floor 1, No.180 1002 Phillips Floor 2, No.
DP100-25 SI MANUAL answered. 5. When call is hang up by receiver, LCD display will show “Hanging Up”. 6. Talking If called extension number is occupied, the bell sounds a busy announcement. 7. If there is no one answering this call, the bell sounds (Ding-Dong) will continuously ring and be discounted OK automatically after 15 seconds.(The time out can be set at Web for 15 ,30 , 45 and 60 seconds). 8. You will see “Disconnected” message on LCD display if the networking is disconnected.
DP100-25 VIDEO DOOR PHONE DP100-25 RFID Card Usage Residents scan RFID card over the card reader. DP100-25 will verify the database to determine whether to Open door or not. Issue Master RFID Card First Time Take the Master RFID Card from package contents to scan on the DP101R RFID reader after the installation of DP101R is completed. The LCD Display will show the card number of the Master RFID Card. This Master RFID Card will be used as Master Card1.
DP100-25 SI MANUAL The new RFID card is authorized and can be used to scan over DP100-25 card reader and open door. Open the Door With the installation of electronic lock, residents can open the door through the following 3 ways to open door. 1. Press “#” key on IP Video Phone/Video Indoor Station to open the door. 2. Resident can press indoor “Open Door Button” to open the door. 3. Resident can scan authorized RFID card on DP100-25 card reader to open the door.
APPENDIX A: ELECTRONIC LOCK Appendix A : Electronic Lock Electronic Lock The DP100-25 can connect with various Electronic locks, including Electronic Strikes, Electronic Bolts and Electromagnetic locks. There are two types of Electronic door lock applications as below. One is Electronic Bolt, and the other is Electronic Strike. For more Electronic locks, please follow the similar method for connection. Electronic Bolt z Electronic Bolt The Electronic Bolt is closed when +12 V is supplied.
ELECTRONIC LOCK Wiring Connection and Web Page Setup There are two connectors: Terminal Connector Pack 1 and Terminal Connector Pack 2 on the rear side of the DP100-25. We provide the example for wiring connection and web page setup of Electronic Bolt. A Door Open Button is connected in the wiring connection.
APPENDIX A: ELECTRONIC LOCK Electronic Strike z Electronic Strike The Electronic Strike is opened when +12 V is supplied. The Electronic Strike is closed when +12V is not supplied. This function can let you not only press the pound key to open the door when you are answering Video Door Phone. but open the door with the Open Door Button directly.
ELECTRONIC LOCK 48 Amroad Technology Inc.
Amroad Technology Inc.
REGULATORY INFORMATION CE DECLARATION OF CONFORMITY (EUROPE) Manufacturer declares that this product conforms to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC: z EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment z EN 609 50 Safety z EN 300-328-1, EN 300-328-2 Technical requirements for Radio equipment Caution: This equipment is intended to be used in all EU and EFTA countries.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.