ZigBee Server User Guide ZigBee Server USER GUIDE Version: 1.
ZigBee Server User Guide Contents Chapter 1: Chapter 2: Chapter 3: Appendix A: Introduction Welcome Installing Using the ZigBee Server 3.1 Internet Protocol (TCP/IP) setting 3.2 Setting IE 3.3 Log in ZS211H Web 3.4 Web UI 3.5 Features 3.
ZigBee Server User Guide Chapter 1 : Introduction Welcome The ZS211H ZigBee Gateway is a stand alone device that allows one to configure and control their ZigBee mesh network using a network-connected computer. The ZS211H can be accessed from anywhere on the IP networks, Ethernet or Internet, allowing one to control their ZigBee devices from home, office or on the road where Internet connectivity is available. This document defines the specifications of this product.
ZigBee Server User Guide Chapter 2 : Installing Package Contents The following items are included in your ZigBee Server package. Check this list before installation to ensure that you have received all items. n ZigBee Server o Power Adapter p Ethernet Cable q Phenix Connecter r Installation CD Please contact your dealer immediately in case you are missing items.
ZigBee Server User Guide Chapter 3 : Using the ZigBee Server ZS211H default I P is 192.168.0.100:3000,default data address of return destination is 192.168.0.200:2000。 3.1 Internet Protocol (TCP/IP) setting: a. On PC home page of Microsoft Windows. Click “right key” of mouse upon 「My Network Place」, select 「Properties」. b.
ZigBee Server User Guide c. Select 「I nternet Protocol(TCP/ I P) 」,click「Properties」.
ZigBee Server User Guide 5
ZigBee Server User Guide d. in 「using the following I P address」 key in I P address: 192.168.0.200,subnet mask:255.255.255.
ZigBee Server User Guide 3.2 Setting IE: a. click「I nternet Explorer 」browser 。 b. click 「Tools」,then 「I nternet Options」。 c. select 「Connections」,keep blank at 「Dial-up and Virtual Private network settings」, then click「LAN Settings」.
ZigBee Server User Guide 8
ZigBee Server User Guide d. Make sure this page is blank and click「ok」. Once more「ok」to escape.
ZigBee Server User Guide 3.3 Log in ZS211H Web: a. Open I nternet Explorer , key in address 192.168.0.100 then 「Enter 」. b. When you see ZS211H home page,select 「Setup Server 」. Login I D : admin,Password :admin,click「Login」,you will enter ZS211H setting page.
ZigBee Server User Guide 11
ZigBee Server User Guide c.
ZigBee Server User Guide 3.4 Web UI : a. Main mannual : Setting、MESH Network、I / O Ports、Alert 、Maintenance b. Sub mannual : You may key in or select proper features.
ZigBee Server User Guide 3.5 Features a.
ZigBee Server User Guide Network : Ethernet setting,I P,DNS,HTTP Port etc… 15
ZigBee Server User Guide Users : Update or modify administrator I D & Password 。 Register new User and password to joint. b.
ZigBee Server User Guide PAN Setting : input or modify ZigBee network setting.
ZigBee Server User Guide Node Setting : Update or modify ZigBee Node setting 。 Update or modify ZigBee Node Service setting 。 c.
ZigBee Server User Guide GPIO : GPI O : I nput Pin Alert’s input level setting。 Output Pin Alert’s input level setting。 19
ZigBee Server User Guide RS485 : RS485 interface setting, and settings of Baud Rate,Work Mode,Data Bit ,Stop Bit ,Parity Check,Terminator 。 d.
ZigBee Server User Guide Setting triggering devices for Service Alert. e.
ZigBee Server User Guide Display hardware version of ZS211H .
ZigBee Server User Guide Show all Services which are set Enable. User can operate them from display panel. 3.6 Hardware rest At rear panel of ZH211H, there is a hardware reset key. Short press once will enforce ZH211H back to default I P address, I P (192.168.0.100). Press longer than 3 seconds, ZH211H will retrieve all system default settings and restart automatically.
ZigBee Server User Guide Appendix Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.