MOVE motor pro MOVE - Bluetooth controlled motor for indoor blinds and shades User manual
Table of Content Warnings and general precautions for safety .................................................................................................... 3 Regulatory and safety notices ............................................................................................................................ 4 Product description and intended use............................................................................................................... 5 All included parts ......................
Warnings and general precautions for safety Read these warnings carefully before you continue installing, connecting and using MOVE device hereinafter called the product. It is very important that you follow the safety and warning instructions written in this manual to ensure a safe use of the product. Keep these instructions. Heed all warnings. Only use the product as described in these instructions.
Regulatory and safety notices Model name: M2009, Product name: MOVE motor pro FCC warnings: FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
Product description and intended use Functional characteristics of the product: -MOVE motor pro is a motor for existing indoor blinds and shades. -MOVE motor pro is built to fit as many different manually controlled indoor blinds and shades as possible. The MOVE motor pro can be retrofitted to nearly all different manually controlled indoor blinds and shades. No matter if its continuous cord loops or bead chain. MOVE devices are installed with screws that are hidden behind the front cover.
Outside device overview 1. 2.4” display with touch 2. Micro USB type B charge port The touch display is used to access the different settings and adjust the position of the window cover where the MOVE device is installed. The MOVE devices can either be controlled directly at the device through the touch display, through a remote control or through an app running on a smartphone or tablet. The remote control can be used with or without the app to control MOVE devices.
Remove the front cover To remove the front cover when the MOVE device is new use the red stickers attached to the device. Use both hands. One hand should hold the sticker that is marked “hold”. The other hand should pull the sticker that is marked “pull”. These stickers should be removed after installation. If the red stickers are not present and the front cover should be removed a pulley need to be attached. One hand should hold the pulley and the other should pull the front cover for it to pop off.
Inside device overview 1. 2. 3. Front cover 2.4” display with touch Micro USB type B charge port 4. 5. 6. LiPo battery 7.4V 2600mAh Wall screw slot Wall screw slot The front cover needs to be removed when installing the MOVE device. The slot screw holes (5 and 6) are supposed to be used when installing the MOVE device. Screws and anchors are included in the package but depending upon the wall where the device is intended to be installed, different type of screws and anchors may need to be used.
Prepare for bead chain size #10, 4.5mm There are two types of pulleys for size #10 bead chain. The small pulley (part 3 in the picture “All included parts” at page 5) is intended for big and heavy window covers and the standard pulley (part 4 in the picture “All included parts” at page 5) is intended for regular size window covers. The size of the pulley will affect the speed of the open and closing of the window cover.
Install the standard pulley for size #10, 4.5mm bead chain Attach the standard pulley (part 4 in the picture “All included parts” at page 5). Install the small pulley for size #10, 4.5mm bead chain Attach the small pulley (part 3 in the picture “All included parts” at page 5).
Prepare support wall for cord loop and small size bead chains When installing a MOVE device to a window cover with cord loop it is important to first install the support wall to the MOVE device. The support wall will make sure the pulley grips the cord and smaller bead chains do not fall out of the pockets of the pulley. The main purpose of the support wall is to prevent slippage of the cord loops or skipping of beads for the smaller types of bead chain.
Remove the Philips screws at each side of the motor axel. Place the support wall so the holes line up. Reattach the Philips screws to fasten the support wall.
Prepare for cord loop D30, K35, C30, 2.7-3.5mm Use the support wall and the standard size pulley (marked 4 in the “All parts included” picture at page 5). Install at cord loop D30, K35, C30, 2.7-3.5mm After the support wall is installed the cord loop should be placed in the standard pulley. The standard pulley is then pressed onto the motor axel and the supplied screw is used to secure the pulley. Then attach the small top part to make sure the cord is always centered and aligned towards the pulley.
Prepare for vertical blinds track cord, bead chain size #6 and size #8 Use the support wall and the pulley that have small pockets (marked 5 in the “All parts included” picture at page 5).
All installations options below require the support wall. After the support wall is installed the cord loop or bead chain should be placed in the small pocket pulley. The small pocket pulley is then pressed onto the motor axel and the supplied screw is used to secure the pulley. Then the small top part is installed to make sure the cord is always centered and aligned towards the pulley. Use the supplied screw to secure the small top part.
Mount device to wall Warning! - Before starting, carefully read the warnings in the first part of this user manual. It is important that you install MOVE device as described in this manual to ensure safe use of the motor. Note! The motor inside a MOVE device has a torque of about 1Nm and incorrect installation and/or usage can be dangerous. Check the condition of the MOVE device upon unboxing it, do not install if damaged.
When the MOVE device is fastened to the wall, just snap on the front cover and mounting is complete. The front cover is available in a transparent version that can be painted or left as is to give the MOVE device a different look, contact your seller for more details.
Charing the battery MOVE devices charge the battery installed in them through a USB type B connector. The USB charger adaptor used must be rated for at least 0.5A and 5V. Set limits Limits in MOVE device can either be set through the app or at the device through the display. Because MOVE device can be installed in many ways there are an option to change direction in the set limit’s view. Set open limit (position 0). This is the maximum open position. Do this 1. 2. 3. 4.
Set speed MOVE devices let the users set different speed for opening and closing direction. The speed that is set will be used both when manually adjusting position but also when automations change the position. The speed can easily be set in the settings menu. To set the speed do this: 1. Wake the device by clicking anywhere in the display 2. Click the settings icon in the top right corner of the display 3. Click the “Set speed” option 4. Use the drawbar to set the opening speed 5.
Reboot the device MOVE devices can be rebooted by selecting this option the settings menu. Do this 1. 2. 3. 4. to reboot: Wake the device by clicking anywhere in the display Click the settings icon in the top right corner of the display Click the “More settings” option Click the “Reboot” option. The device will do the reboot and then load the main view Factory reset To clear all settings and go back to the default state of a MOVE device, a factory reset can be performed.