User's Manual

Product Overview
LED Indicator
Button (Left)
Name Tag
Micro-USB
5-pin connector
Button (Right)
Reset Hole
Turning on
When both buttons are pressed at once, toggle LED
turns on and then noise level and vibration level alarm
goes off.
Message Transmission / Tracking mode feature is activated.
BLE Mode
1. BLE mode on : press left button for five seconds
2. BLE mode off : press left button for five seconds
*BLE mode
1. enables engineers to update firmware via BLE.
2. When BLE mode is on, the normal mode function
does not work.
Charging & Rebooting
Emergency Mode
NFC Tag feature is
triggered by the usual
motions
Micro-USB
5-pin connector
Reset Hole
Specification
Two buttons on each side to prevent malfunction
RFID/NFC Tag (Door Tag)
Haptic feedback for button or event alert trigger
Geo-location using WPS
RF
MCU
Geolocation
Connectivity
Antenna
User Interface
Embedded Sensors
Rfid
Battery
Charging
: Sigfox RC1/2/3/4/5/6 Uplink Class0u(>12dBm EIRP for RC1,
>20dBm@RC2)
: 32-bit Arm® based Cortex®-M0, 256KB Flash
: 2.4GHz WiFi Sniffing
: 2.4GHz Bluetooth LE 5.0 (BLE Advertising) 13.56Mhz NFC
(MiFARE DESFire)
: Internal Sigfox/WiFi/PCB pattern
: 7-color LED Indicator (Batt., TX/RX, Alert, Successful button
press, Charging)+ Push Button(2ea) & Haptic vibration
: 3-axis nano accelerometer : ±2~16g
: Mifare classic 4K
: Rechargeable Lithium-polymer cell (3.3V 500mAh) with
micro-USB 5-pin connector
: 5V micro-USB, Wireless Power Charging
Press both buttons for three seconds
Normal Mode
1. Transmitting messages: sound of alarm siren, LED,
vibration, message transmitted after 10 seconds
2. Canceling false alerts: press both buttons within
10 seconds after sirens go off
3. Siren turned off: press both buttons for three seconds
4. Siren muted : press right button for three seconds
*The Sigfox TX message is sent after WiFi scanning.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Safety Information
Refrain from using while it is charging.
DO NOT drop, strike, or shake the device.
DO NOT use in high-temperature environments.
DO NOT disassembles as it may cause malfunctions.
DO NOT charge in voltage over 5V, 2Amps.
FCC Caution
Personal ID Tracker
SB50-SW
ATOZ
User Manual
Address
Mobile
Email
AMOSENSE Co.,Ltd.
Customer Support
: 165 North Archer Avenue Mundelein, IL 60060, USA
: 1-224-619-6579
: [e-mail]