Sky Link outdoor User Manual AMN0504PBLR Tx - AMN35223_PM & Rx - AMN36254_PM צmmmmmcm www.amimon.
Rx without enclosure An AMIMON Inc. Document Copyright 2013 Version 1.
Important Notice AMIMON Ltd. reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to AMIMON's terms and conditions of sale supplied at the time of order acknowledgment.
AMIMON ne garantit ni ne déclare que toute licence, explicite ou implicite, soit accordée en vertu d'un brevet AMIMON, de droits d'auteur, masque droit de travail ou autre droit AMIMON de la propriété intellectuelle relatif à toute combinaison, machine ou processus dans lesquels les produits ou services AMIMON sont utilisés.
Revision History Version Date Description 1.0 05 May 2013 Initial Draft 1.1 07 May 2013 Initial Draft 1.2 18/08/2013 Changed the input voltage value 1.3 29/10/2013 Fixed the product number 1.4 28/11/2013 Add registration with button, Update the Equipment list 1.5 31/12/2013 General overhaul 1.6 20/1/2014 Inserting notice in French and FCC Warning 1.7 19/2/2014 Supports MAC 30.0 1.8 23/02/2014 Added more detail 1.
Table of Contents Safety Instructions .....................................................................................................8 Caution ......................................................................................................................8 Overview....................................................................................................................9 Package Contents ....................................................................................................
OSD - Menu ............................................................................................................. 26 Link Quality Indicator ............................................................................................... 28 Technical Specifications ........................................................................................... 29 Specifications ....................................................................................................... 30 Troubleshooting ........
Safety Instructions When operating this equipment, read and follow all the instructions in this manual. Do not open unit. Do not block the air ventilation openings. Use only accessories specified or recommended by Amimon. When devices are switched on keep away at least 20cm from your body. Do not expose to moisture or excessive heat. Keep devices away from water Use the mains plug to disconnect the apparatus. Clean with a dry cloth only.
Overview The HD SkyLink system was designed to establish wireless HD video signal transmission without any latency over large distances. Amimon finally made this possible with revolutionary technology! The HD SkyLink is a lightweight but still very powerful wireless HD system, which is the perfect solution for live streaming from your multicopter or from a steadycam system. The HD SkyLink transmits encoded but uncompressed signals.
Package Contents Please verify the following items are in the shipping box, prior to installation of the - AMN35223_PB transmitter and Amimon-AMN36254_PR2 receiver: ITEM DESCRIPTION QUANTITY HD wireless video transmitter 1 HD-SDI wireless video receiver 1 12V Power Supply (optional) 2 (optional) SDI cable (optional) 1 HDMI cable (optional) 1 Remote Control (optional) 1 USB to mini USB cable (optional) 1 2/5dbi (depending on region) OMNI directional antennas for 2 Transmitter (optional)
Product Description 1.1.1 AMN35223 - General Guidelines (Tx) Figure 1 - Tx AMN35223 Description of all connectors and their functionality including USB, Pass through, power conn pin out debug connectors, 1.1.1.
09- External antenna UFL connector CH#1 10- LED #1 - NETWORK status 19- DIP Switch- 1 – BOOT1, 2- DIP0 20- MAC DEBUG Port Transmitter 1 Antenna connectors 8 5V 2pin generic connector 2 Network status LED 9 MiniUSB port - Used for firmware updates 3 Video status LED 10 N/A 4 Power LED - Indicates battery 11 N/A status 5 Registration button 12 Mode slide switch - Switches between Aerial and Multi-monitor mode 6 Reset button 13 HDMI input port - For connecting the HD video source to the H
Slide switch - operation mode selection Mode Slide Switch Not in use AUDIO Aerial mode Multi-monitor mode LED behaviors – Transmitter Network LED BLINKING MODE DESCRIPTION Solid When a connection to Rx is established Slow Device is in listen mode Normal Fast During link setup mode/during Registration System Error (Video LED flashing as well) Video LED BLINKING MODE DESCRIPTION Blinking mode Description Solid Video signal is locked Normal Video is not supported Fast System Error (Netwo
Receiver 1-5 External antennas 18 Registration Button/Link quality button 6-10 Internal antennas 19 Input voltage connector 7-17v 11 Power connector 7-17v 20 ON/OFF switch 12 DFS antenna (located on the other 21 USB port side) 13 Power LED 22 IR input connector 14 Video LED 23 HD-SDI output 15 Network LED 24 2D-SDI output 16 N/A 25 Reset button 17 DIP switches 26 DC power connector 7-17v
LED behaviors - Receiver Network LED BLINKING MODE DESCRIPTION Solid When a connection to Tx is established*/Link quality is good Slow Device is in listen mode/Link quality is reasonably good Normal Fast During link setup mode/during registration System Error (Video LED flashing as well)/Link quality is poor *In Aerial mode even when Tx is out of range.
DIP switches - operation mode selection DIP SWITCH UP DOWN #1 Default N/A #2 Default N/A #3 Default N/A #4 Aerial mode Multi-Monitor mode
Operating modes Aerial mode In this mode a link is established between a single receiver and a single transmitter. This mode uses DFS frequencies as well making it flexible and easy to adjust to all different fields of use and to meet the regional and national frequency requirements and laws. For some SkyLink version the message "please wait 60 seconds" may appear on the monitor when the link is first established to inform the user that the system is searching for a free DFS frequency.
Multi-monitor mode In this mode a single transmitter can establish a link with several receivers. A link can be established even when the systems are not within close proximity to each other. Operating Frequencies FREQUENCIES [MHz] DESCRIPTION 5755 Non-DFS 5795 Non-DFS Switching between Aerial and Multi-monitor modes Switching between Aerial and Multi-monitor will be done by toggling DIP switch #4 on the Rx side and sliding Mode Slide switch on the Tx side.
Installation Transmitter See Transmitter Product Description for port location described in this section. 1. Switch on Source. 2. Connect the Amimon - AMN35223_PB transmitter to the HD video source via HDMI input port (port #13). 3. Connect the Amimon - AMN35223_PB transmitter to the 7-17v power, via the Lemo connector (port #14). 4. Antenna orientation: It is recommended to separate the antennas so that they form a "V" (as shown in the picture).
Remote control Remote Control Hotkeys ADD - Direct access for starting the registration process on the receiver. Delete - will open the "Remove Video Source" in the OSD menu to allow the user to choose to remove devices from the list of registered devices. Video Source Keys – These three keys (1st/2nd/3rd Video Source) will toggle between the first, second or third source registered with the receiver, in order of appearance on the registered sources list.
Registration Amimon products require registration between the transmitter and receiver, in order to establish a wireless link. The registration process includes keys exchange, for enhanced security and can be managed using the remote control, provided with the product. Sets of Amimon - AMN35223_PB transmitter and Amimon-AMN36254_PR2 receiver usually arrive prepaired, when purchased as pairs. In such case, video link will be established automatically after completing installation.
Registering without remote control If there is no transmitter registered to the receiver, you should see an OSD menu on the monitor. 1. Connect the HD Source to the Amimon-AMN36254_PR2 transmitter. 2. Connect a HD-SDI cable from the Amimon-AMN36254_PR2 receiver to the HD display*. 3. Turn on the transmitter and receiver. 4. Long press the Registration button [#18] on the Rx. 5. The message “Please Activate the Registration on Transmitter Unit” will appear on the monitor. 6.
14. When all the receivers have been registered to the transmitter power on all the receivers one by one. 15. The video should be displayed on all monitors. *The registration process can be done without HD source, an OSD message will appear to notify of missing video source. Registering multiple transmitters to a receiver 1. Connect the HD Source to the Amimon - AMN35223_PB transmitter*. 2. Connect a HD-SDI cable from the Amimon-AMN36254_PR2 receiver to the HD display. 3.
Unregistering transmitters 1. Power on the Amimon-AMN36254_PR2 receivers. 2. Use the remote control at the Amimon-AMN36254_PR2 receiver and Press the “Delete” Hotkey button. 3. Select the source to be removed, using the up, down arrow buttons, and “OK” button. 4. Confirm removal of the selected source by pressing the “OK” selection by pressing the “Exit” button. 5. Wait 30 seconds for the removal process to be completed. 6. Transmitter removal is complete.
Switching between transmitters 1. In order to switch between video transmitters, press the “SOURCE” button and a menu will appear 2. Choose the desired transmitter using the up, down arrows, and “OK” buttons. *Note this is a Unicast product, the desired transmitter must be disconnected from any another system before being chosen. 3. The existing video link will be lost and within 30 seconds, the new transmitter will connect and new video link will be established.
OSD - Menu The Amimon-AMN36254_PR2 receiver generates an OSD-Menu (On-Screen Display). This is used for adding/removing devices and presenting the link status and technical information. OSD - Setup window In order to open the Setup window Use the remote control at the Amimon-AMN36254_PR2 receiver and Press the “Menu” Hotkey button. The Setup window contains: Add new source, Remove source, Modify name source and Status menus for technical information.
In order to modify the source name, follow the instructions below: 1. In order to modify the transmitter name press the “MENU” button to open the OSD menu. 2. Choose the “Modify Video Source Name” option using the up and down arrows. 3. Press the “OK” 4. A list of all the registered transmitters will pop up. 5. Choose the source to rename using the “Up” and “Down” arrow buttons. 6. Press “OK” 7. Choose the characters you wish to modify using the right and left buttons on the remote button.
Link Quality Indicator The link quality indicator gives the user an indication of link quality. When enabled this indicator appears in the top left corner in three different colors, depending on the quality of the link: - Very good - Reasonably good - Poor In order to enable the indicator the user must short press the link quality button on the Receiver during link.
Technical Specifications SPECIFICATION DESCRIPTION Video Resolution: 1080p/50, 1080p/60, 1080/59.94i, 1080/50i, 1080/29.97p, 1080/23.98p, 720/59.94p, 720/50p, 525i/59.94, 625i/50, 1080/24p. Frequencies: Non-DFS Frequencies : 5.170~ 5.250 GHz for EU 5.170 ~ 5.250 GHz and 5.735~5.815 GHz for US DFS Frequencies (used only in Aerial mode): 5.250-5.330 GHz and 5.490 ~ 5.690 GHz for EU 5.250-5.330 GHz and 5.490 ~ 5.590 GHz and 5.650 ~ 5.690 GHz for US ISM Frequencies: 5.725 ~ 5.
Specifications Amimon - AMN35223_PB transmitter and Amimon-AMN36254_PR2 receiver Video Interface Audio Frequency Control Antenna Voltage Size User Control TRANSMITTER AMN35223 HDMI male connector RECEIVER AMN36254 SDI splitter Option to connect external connector board Over HDMI. Supports up to 2 channels.
Troubleshooting Registration fails Make sure both transmitter and receiver are powered on. Make sure the power cable is continuous. Make sure that pairing units are the only Amimon devices currently powered on. Bring the transmitter and receiver closer together but no closer than 1 meter. Keep the number of solid walls between the transmitter and receiver to a minimum. No Signal on monitor Make sure the receiver is powered on. Make sure the monitor is powered on.
Make sure the IR receiver is connected to the Amimon-AMN36254_PR2 receiver. Make sure there is a far enough distance between the IR receiver and any fluorescent lighting or radiation interfering with the IR signals.
Other malfunctions The receiver keeps outputting a “Searching…” message, and the NETWORK LED is constantly blinks: It should take up to one minute to establish a wireless link. If the link was not established within that time period, verify the transmitter is powered on and not connected to another receiver. The receiver is outputting “Connected to source name, Please Check Video Source”: Check the HD-SDI connection between the transmitter and the video source.
Appendix Tx without enclosure Rx without enclosure