ys TM Smart Inflate™ Blood Pressure Monitor Instruction Manual Features: • Smart Inflate™ Technology • Auto memory for up to 60 readings • One-Touch Operation • Pre-Programmed Alert Feature • Easy-to-read Display • Time and Date Display 106-940
Table of Contents Smart Inflate™ measuring technology . . . . . . . . . . . . . . . . . . . . 3 Statement of accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About blood pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Blood pressure standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Blood pressure fluctuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before taking a measurement . . . . . . . . . . . . . . . . .
Smart Inflate™ Measuring Technology This Physio Logic™ monitor uses trend-setting Smart Inflate™ Technology to detect your blood pressure. With one touch of a button, it will automatically start to inflate and determine your blood pressure by analysing your pressure oscillations while inflating. When the measurement is completed, the device will automatically deflate the cuff and display your systolic, diastolic, and pulse. Measurement time is significantly shortened and user comfort is greatly enhanced.
Blood Pressure Standard The Joint National Committee on prevention, detection, evaluation, and treatment of high blood pressure has developed a blood pressure standard, according to which areas of low and high risk blood pressure are identified. This standard is a guideline as blood pressure varies among different people and different age groups... It is important that you consult with your physician regularly.
Before Taking a Measurement To help you obtain more accurate readings: • Urinate if necessary. • Remove any clothing and jewellery from your left arm. Placing the cuff on anything other than bare skin can result in an inaccurate reading. • Sit in a comfortable position with your legs and ankles uncrossed and your back supported. • Sit quietly for 15 minutes before measuring your blood pressure. • If you need to retake a reading, wait at least 5 minutes to allow your circulation to return to normal.
Name / Function of Each Part Date / Time - Set button On / Off / Start button Memory recall button LCD display Battery compartment Arm cuff Air tube and connector INDEX 2 ~ 3 cm 0.8~1.2 inch K O INDE X 22~32 cm 8.7~12.
Display Explanation Date and time Systolic pressure Diastolic pressure Pulse rate Appears when measurement value is stored in memory or is recalled from memory. Appears when blood pressure reading is higher than 160 mmHg (sys.) or 95 mmHg (dia.) Appears when batteries should be replaced. Shows the pulse rate per minute. Occurs when a error was made during measurement. Installing Batteries 1. Press down and lift the battery cover in the direction of the arrow to open the battery compartment. 2.
Recalling Memory 1. To recall stored blood pressure readings from memory, simply press the Memory button. The last set of memorized readings will be displayed. 2. Another press of the Memory button will recall the previous set of readings. Time Adjustment 1. Press and hold the ( ) button for more than 3 seconds to enter Time Adjustment Mode. The display will show a blinking Month. Hold for more than 3 seconds Blinking month 2. Press the “+” or “–” to change the Month. 3.
Applying the Arm Cuff IN IN DEDEX X 1. Insert the cuff’s connecting tube into the unit. 2. Unwrap the arm cuff, leaving the “Index” end of the cuff through the D-ring of the cuff. 3. Put your left arm through the cuff loop. Position the artery mark ( ) at the middle of your arm above the elbow, in line with your middle finger. Tighten the cuff by pulling the “Index” end of the cuff (snug, not tight). 4. Turn your left palm upward and place the edge of the arm cuff at approximately 2 to 3 cm (0.8” - 1.
Taking a Measurement 1. Press the On / Off / Start button. All displays will appear for approximately one second before returning to “0”. 2. The unit will automatically start to inflate and begin to measure your blood pressure. During inflation, a changing measure of the cuff pressure will be shown on the display. 3. When pressure reaches your systolic blood pressure, the monitor will deflate the cuff automatically.
Troubleshooting Symptom: No display when the On / Off / Start button is pressed. Correction: If the batteries have run down, replace them with new alkaline batteries. If the batteries are not in the correct position, re-insert them with the correct polarities. Symptom: EE mark shown on display or the blood pressure value is displayed excessively low (high). Correction: Wrap the cuff properly so that it is positioned correctly. If you talked or moved during the measurement, measure it again quietly.
Specifications Measurement method Measurement range : Oscillometric : Pressure: 20 to 280 mmHg ; Pulse: 40 to 180 beats / min.
