Getting Started Guide

WI-FI ENABLED PIVOTING UNDER CABINET LIGHT
PPCCT-L24W-WIFI INSTRUCTIONS
Getting Started
1. Read these instructions in their entirety before installing or using this product.
2. Do not mount this light over a sink or a stove, in small enclosed spaces, or in
wet locations.
3. For use with 120V, 60Hz electrical power only.
4. Do not use on a dimmer-controlled outlet or when connected to a dimmer.
This light features on-unit dimming and is not compatible with external
dimmers.
5. This light is linkable with other Westek PPCCT models. Never link more than
240 Watts of PPCCT lights total. NOTE: WiFi will only work with PPCCT-WIFI
models.
WARNING
This light may present a possible shock or fire hazard if not properly
installed. Products should be installed in accordance with these
instructions, current local electrical codes, and/or the National Electric
Code. Always follow all grounding directions.
Choose Your Installation Method
Determine your installation location and method for connecting 120V power to the fixture. Lights connected to the house wiring with the use of a plug and
power cord and are generally simpler to install. Direct wire units are designed to be permanently mounted and are directly connected to the house wiring
through junction boxes, and offer some benefits such as the ability to connect to switches, but are often more complex to install. Because local codes vary, we
cannot offer exact guidance on how to direct wire this light to meet your local building codes. If you are not sure how to install this light properly, consult a local
licensed electrician or electrical contractor before proceeding.
Mounting the Light
Place the light against desired mounting surface and use a pencil to mark the spot where the screws will be located,
as shown in Figure 1. For best lighting aesthetics, we recommend mounting your light towards the front edge of
your cabinet with the pivoting head positioned towards the rear of your cabinet; this position usually gives the best
adjustability of the light, however you may mount it in any desired position based on your preferred aesthetics. If
installing to wood cabinets, use the included screws and drill 1/16” pilot holes. Caution: Check your cabinet thickness
first and use a drill depth stop to avoid drilling through your cabinet. Secure the light to your cabinet using a #2 Philips
screwdriver and the included screws. If mounting to drywall, use wall anchors rated for the application and weight (not
included).
Operating the Light
Power on the light by pressing the power button.
The light will start in its last-used state. When
brand-new, the light may flash to indicate WiFi
pairing mode is active. If you wish to pair to WiFi,
follow the instructions in the WIFI OPERATION
section. Otherwise, pressing any button on the
light will enter into normal operating mode.
Thank you for your purchase of this adjustable white WiFi-enabled pivoting under cabinet light. Whether
you want a bright white task light or the ambiance of a subtle warm white glow, this light has you covered
with infinitely-adjustable brightness and 3000K, 4000K & 5000K modes accessible directly from the light.
Or, pair to WiFi and enjoy any color temperature from 3000K to 5000K. With the Westek app, you can
even set your lights so you wake up to a soft glow and slowly ramp up to a full-bright daylight lamp. Or
better yet, let Alexa or the Google Assistant adjust them for you - the choice is yours!
Installing the Light
Plug In Installation
Connect the 5’ power cord to the power input of the light. The power input on the light is on the side of
the light closest to the power buttons. If installing more than one compatible light, these lights may be
linked together using the included linking cable. The linking cable connects to the power output port of
the first light, located on the end further from the power buttons, and connects to the power input of the
second light. WARNING: Do not conceal power supply cords inside a wall, ceiling, soffit, cabinet, or other
enclosed structure. Do not run power cords through holes in walls, ceilings or floors. Use only UL-Listed
cable staples to secure the wire to the bottom of the cabinet or wall for a clean-looking installation.
Direct Wire Installation
WARNING: Before installing this light, make sure to de-energize the electrical circuit, and do not re-
energize it until you have completed the installation.
Install the light in accordance with all applicable building codes and regulations. If you have any questions
on proper installation or regulations, consult a licensed electrician. To install, remove the desired knockout
on the back or rear access panel of the light and install the included strain relief connector as shown in
Figure 2 and wire the light as shown in Figures 3 & 4. Do not leave any open holes on the housing - if you
remove more than one knockout, plug the un-used knockouts. This light should be wired with 14 AWG
or 12AWG armored or non-metallic cable as required by your local electrical codes and/or the National
Electric Code. This light should not be connected to an external dimmer switch - dimming is controlled
on-unit or via WiFi.
This light fixture can be installed via direct wire or with the included 5’ Power
Cord. When using the power cord, this light must be plugged into a grounded
outlet - do not use an adapter, extension cord, or alter the plug in any way.
• To dim the light, press and hold the POWER
button. The light will pause at its maximum
and minimum brightness settings.
• To adjust the color temperature of the light,
press the WHITE ADJUST button. The light
will scroll through 3000K > 4000K > 5000K.
• When finished operating your light, tap the
power button to power it off.
Figure 1
Figure 2
Figure 3
Figure 4
Locate Holes
Rear Access Panel
Knockout
Cable Connector
AC Supply Wires
Armoured or
Non-Metallic Cable
Connector
Ground (Green or
Copper) Supply Wire
Hot (Black) Supply Wire
Hot (Black) Fixture Wire
Ground/Yellow
Fixture Wire
Neutral (White)
Supply Wire
Wire Nuts
Neutral (White)
Fixture Wire
Armoured Cable (BX)
Non-Metalliuc Cable (NM)
Wire Nuts