User's Manual

Wireless RF Remote Control System RFK106

Hand Held Transmitter and Plug-in Receiver

Imagine turning on your house lights from inside your car. Or turning off your stereo from

across the room. This wireless Radio Frequency(RF) control now makes it possible. RF

Controls are an easy, convenient way to remotely control lights, and appliances in and

around your home or office. The invisible RF signal passes through walls, dorrs, ceilings,

floors and even around corners. Simply plug the desired appliance into the receiver and

the receiver into any outlet. A press of the button on the hand held transmitter, turns

whatever you, ve plugged into the reciever on or off.

Channel Code Information

Three operating channels are available so you can control three separate at defferent

locations in your home. Be sure to match common frequency channels, for those devices

you want operated by the same swith.

INSTRUCTIONS

Notes: The total load of appliances connected to the Plug-in Receiver should not exceed

1800 Watts or 15 Amps.

Do not use Plug-in Receiver to control appliance loads that may be dagerous to turn on

remotely(i.e. power tools).

The Plug-in Reciever must be located within 100 feet of the Wall Transmitter.

A Remove back cover of Hand Held Transmitter by pushing cover down.

A Remove plastic battery tab by gently pulling it from the battery compartment(this tab is

isolates the battery until it’s ready for use and insures that you’ll have a fresh battery).

A Reassemble Hand Held Transmitter.

A plug your light/appliance into the outlet on the Receiver being careful to match the wide

slot on the outlet.

A Plug the Receiver into any standard ground 110/120 Volt outlet being careful to match

the wide blade of the Receiver with the wide sloton the outlet. Fully insert.

A Hold your hand Held Transmitter at the location where you wish to use it.

A Press Switch to determine if your light/appliance turns on and off. If your light/appliance

does not repond try relocating the transmitter or receiver. Large metal objects such as

metal doors should not be in the way of the Transmitter and Plug-in Receiver since this

could decrease the range of the RF signal.

A Attach transmitter to any keyring or place in a convenient location around the house.

OPERATION

Simply press the button on the Hand Held Transmitter to turn the light/appliance you’ve

plugged into Receiver on or off.

Note: Wait at least 3 seconds after you press the transmitter on or off before you press it

again. This allows for the RF signal transmission to be completed.

PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

PAGE 1
Wireless RF Remote Control System RFK106 Hand Held Transmitter and Plug-in Receiver Imagine turning on your house lights from inside your car. Or turning off your stereo from across the room. This wireless Radio Frequency(RF) control now makes it possible. RF Controls are an easy, convenient way to remotely control lights, and appliances in and around your home or office. The invisible RF signal passes through walls, dorrs, ceilings, floors and even around corners.
PAGE 2
BTTERY REPLACEMENT Your RFK106 battery should last 2-3 years under normal use. To replace battery: A Remove back cover of Hand Held Transmitter by pushing cover down. A Remove battery from Battery Compartment and replace with another 12Volt battery(Radio ShackTM 23, 23M, VR22,EL22 or equivalent). Troubleshooting Guide SYMPTOM PROBABLE CAUSE Light does not turn on. 1. 2. 3. 4. 5. Light does not turn off. 1. Light comes on randomly. Circuit break of fuse is turned off. Swith on lamp is turned off.
PAGE 3
REMINDING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.