Installation Guide

ManualsBrandsAmerican Standard ManualsBathSerin Wall-Mount AC Powered Single Hole Touchless Bathroom Faucet 0.35 PGM in Chrome

Installation Instructions

SERIN

™

Wall Mount Electronic

Proximity Lavatory Faucet

Certified to comply with ASME A112.18.1

Product No.'s & Options

Specications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Replacement Parts

2-5

6-8

9-10

10-11

T064.34X T064.35X T06B.30X

MODEL NUMBERS

M965613 REV. 1.8 (11/16)

NOTE: Please refer to R350 Mounting Kit

installation instructions #M965614 prior to

faucet installation.

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS

supplied cables, or cutting, splicing or modifying

any components will void the warranty.

Summary of content (13 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SERIN™ MODEL NUMBERS Wall Mount Electronic Proximity Lavatory Faucet T064.34X T064.35X T06B.30X CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. NOTE: Please refer to R350 Mounting Kit installation instructions #M965614 prior to faucet installation. Certified to comply with ASME A112.18.1 Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
GENERAL DESCRIPTION: Roughing-in Dimensions Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in checks, and flexible stainless steel 16-1/4" reach inlet hose for spout connection. 70mm (2-3/4) DIA. FINISHED WALL 150mm - 225mm MIN. (5-7/8) - MAX.
PAGE 4
1a INSTALL SPOUT MOUNTING KIT; Fig. 2 Fig. 2 7 1. Make sure that SEAL (7) is installed into the groove on the back of the MOUNTING FLANGE (8). Feed the CORD HOLDER (3a) and the EXTENSION CABLES (5a) through the MOUNTING FLANGE (8). 9 8 3a 2. Install the MOUNTING FLANGE (8) to the wall with three SCREWS (9) that thread into the MOUNTING PLATE (10) within the wall. DO NOT fully tighten the SCREWS (9). HAND TIGHTEN ONLY. 1b INSTALL SPOUT ASSEMBLY; Fig. 3 10 5a Fig. 3 1.
PAGE 5
1d ALIGN SPOUT ASSEMBLY; Fig. 5 Fig. 5 SPOUT LENGTH 150mm - 225mm MIN. (5-7/8) - MAX. 8-7/8 1. Align and push SPOUT (12) through hole, loosely installed MOUNTING FLANGE (8) and MOUNTING PLATE (10). 10 8 9 2. Once MOUNTING FLANGE (8) is aligned with MOUNTING PLATE (10) opening, tighten the three MOUNTING FLANGE SCREWS (9). (Tighten each screw little by little to avoid missalignment!) 3. Align and slide and COMPRESSION SEAL (14) and COMPRESSION RING (13) to MOUNTING FLANGE (8).
PAGE 6
2 INSTALL SUPPLY ELBOW ASSEMBLY & CONTROL BOX; Fig. 7 and Fig. 7a Fig. 7 23 15 22 1. Install HOSE CLAMP (22) onto SPOUT HOSE (15). Install SPOUT HOSE (15) onto ELBOW NIPPLE (23). Fully tighten HOSE CLAMP (22) to secure SPOUT HOSE (15) to ELBOW ASSEMBLY (24). Fig. 7. 2. Using the ANCHORS (25) and SCREWS (26) supplied, attach ELBOW ASSEMBLY (24) to finished wall, covering the hole in wall. Fig. 7. 25 26 Fig. 7a 3. Remove CONTROL BOX COVER (27).
PAGE 7
ELECTRICAL INSTALLATION Fig. 1 1 2 Product Plug-in AC Powe Kit (PK00.PAC) Page 7 Hard-Wired AC Prower Kit (PK00.HAC) 7 MULTI-AC Power Kit (PK00.MAC) 8 Fig. 1a Fig. 1b A PWRX & STANDARD BATTERY; Fig. 1 3 1. Remove CONTROL BOX COVER (1) from CONTROL BOX (2). Fig. 1. 7 4 5 INSTALL BATTERY 2. Feed the EXTENSION CABLE (3) from the Faucet through SIDE GROMMET (4). Fig. 1a. 6 4.
PAGE 8
B AC VERSIONS (HARDWIRE / PLUG-IN); Fig. 2 1 Fig. 2 and Fig. 3 CAUTION 2 Before opening CONTROL BOX disconnect AC power supply. 1. Remove CONTROL BOX COVER (1) from CONTROL BOX (2). Fig. 2. 2. Feed the EXTENSION CABLE (3) from the faucet through GROMMET (4). Then connect the SOLENOID CABLE (5) to EXTENSION CABLE (3). Install CONNECTOR LOCKING DEVICE (6). Fig. 2a. FOR PLUG-IN HOOKUP ONLY; Fig. 2 Fig. 2a 3. Insert POWER CORD (9) through OUTER GROMMET (10) as shown.
PAGE 9
Fig. 4 Unit #1 Unit #2 Unit #3 10 ft. EXTENSION CABLE AC POWER SUPPLY O R 10 ft. EXTENSION CABLE *MAXIMUM OF 15 UNITS PER AC POWER SUPPLY. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. YOU CAN USE EITHER THE PLUG-IN OR HARD-WIRED TRANSFORMER. OR 4" (102mm) SQ. X 3-1/2" (89mm) DEEP CONTROL BOX Hubbel-RACO #256 OR EQUAL (BY OTHERS). Fig. 4a C FOR AC-VERSION Unit #1 Detail (MULTI HOOK-UP); Fig. 4 and Fig. 4a 1. Remove COVERS from all CONTROL BOX (2). Fig. 4 and Fig. 4a. 4a 11a 2.
PAGE 10
START-UP / MAINTENANCE Fig. 1 A HAND WASH SENSOR OPERATION; Fig. 1 ! Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for 15 seconds after power is connected. When the Sensor detects a user, the water immediately starts to flow. Water flow will stop 1.5 seconds after user is out of sensor range. This comfort timer allows the user to move his hands without the flow cycling on and off.
PAGE 11
D HOW TO CLEAN AND REMOVE Fig. 4 THE AERATOR OR SPRAY; Fig. 4 9 1. Remove AERATOR or SPRAY HOUSING (7) with KEY supplied with faucet. 8 2. Remove AERATOR or SPRAY (8) from HOUSING (7). 7 7 3. Clean the AERATOR or SPRAY SCREEN (9). 4. Reassemble and install into spout end. Be sure the black seal washer is in place. E HOW TO CLEAN FLOW REGULATOR; Fig. 5 KEY Fig. 5 1. Remove SUPPLY HOSE (10) from SPOUT ELBOW ASSEMBLY (11). Pull out FLOW REGULATOR (12) from SPOUT ELBOW ASSEMBLY (11). 2.
PAGE 12
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.
PAGE 13
SERIN™ Wall Mount Electronic Proximity Lavatory Faucet M970040-0070A HOSE ASSEMBLY WITH CLAMPS M907815-YYY0A ESCUTCHEON MODEL NUMBERS T064.34X T064.35X T06B.30X Appropriate finish code CHROME SATIN NICKEL 002 295 M964911-0070A SENSOR KIT M964913-YYY0A AERATOR KIT (1.5 GPM) M964847-YYY0A SPRAY KIT (0.5 GPM) M964964-YYY0A AERATOR KIT (0.35 GPM) PWRX Battery Pack T064.