Installation Guide

ManualsBrandsAmerican Standard ManualsTub FillersAmerican Standard Edgemere Deck Mounted Roman Tub Filler with Built-In Diverter

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

INSTALL SPOUT

Edgemere

Roman Tub Filler

INSTALLATION

INSTRUCTIONS

T018900

T018901

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

M965981 (8/18)

1" MAX.

(25 mm)

3-3/4"

(96 mm)

(51 mm)

4-1/8"

(105 mm)

5-1/16"

(129 mm)

9-3/16"

(233 mm)

8-7/16"

(215 mm)

8-1/4"

(210 mm)

10-3/16"

(258 mm)

8" TO 16"

FLEXIBLE INSTALLTION

(203 TO 406 mm)

Adjustable Wrench

Channel Locks

Flat Blade Screwdriver

Phillips Screwdriver

Hex Wench

(supplied)

Hex wench

(supplied)

RECESS

MOUNTING

SURFACE

• Apply 4-5 drops of THREADLOCKER (1)

on DIVERTER INSERT (2) threads (supplied).

NOTE: If installing on nished deck, install DIVERTER

INSERT (2) through WASHER (6).

• Thread DIVERTER INSERT (2) carefully until it touches the

installation surface, be sure the RUBBER RING (5)

is properly seated in it’s RECESS at the base of the

SPOUT (3).

• Thread SET SCREW (4) using 5 mm hex wrench supplied.

Make certain SET SCREW (4) is properly aligned and tight

so that SPOUT (3) is locked in place.

ROUGHING-IN

DIMENSIONS

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS T018900 T018901 Edgemere® Roman Tub Filler Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
VALVE ASSEMBLY • Remove PLASTER GUARDS. • Thread INSERT (1) into SIDE VALVE (2) until it touches the installation surface. • Thread INSERT (3) into SIDE VALVE (4) until it touches the installation surface. • Tighten COUPLING (5) into TEE (6) for products without hand shower. 3 1 VALVE LOCKING FITTING MOUNTING DECK COLD VALVE LOCKING 4 SPOUT SHANK 6 5 HOT 2 3 INSTALL HANDLES • Turn VALVE to OFF position.
PAGE 3
4 HANDSHOWER INSTALLATION (FOR MODEL T018901 ONLY) • Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12” max from SPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). • Add SEAL WASHER (3) and connect HOSE (8) to outlet nipple at the bottom of TEE (5). Tighten firmly. • Slip SHOWER HOSE (6) with COUPLING NUT through SPRAY HOLDER (4) and ESCUTCHEON (1).
PAGE 4
Edgemere® Roman Tub Filler MODEL NUMBER T018900 T018901 M970522-YYY0A TRANSFER KNOB KIT (T018901) M910270-0070A STREAM STRAIGHTENER M970261-0070A SET SCREW M911705-0070A RUBBER RING M970507-0070A TRANSFER ASSEMBLY (T018901) M970521-YYY0A LEVER HANDLE ASSEMBLY For T018901 Only 1660608.