Installation Guide

ManualsBrandsAmerican Standard ManualsPlumbingGreen Tea 1-Handle Tub and Shower Faucet Trim Kit in Polished Chrome (Valve Sold Separately)

Recommended Tools

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

Plumbers' Putty or Caulking

Phillips Screwdriver

Teflon Tape

FINISHED WALL

TOP OF TUB RIM

BOTTOM OF TUB

74" FOR HEAD

CLEARANCE

5" REF.

1-5/8" TO 3"

18" OPTIONAL

4-5/8" REF.

5-7/8" REF.

1/2" NPT

1/2" COPPER

7-1/2"

12" REF.

OPTIONAL TO FINISHED

FLOOR USUALLY

BETWEEN 65'' AND 78'

"SEE ILLUSTRATION "

Certiﬁed to comply with ANSI A112.18.1

ROUGHING-IN DIMENSIONS (For reference only)

To assure proper positioning in relation to wall, note roughing-in dimensions.

PRESSURE BALANCING BATH

AND SHOWER TRIM KIT

GREEN TEA

Installation

Instructions

T010.5XX

THREADED INLETS (STOPS)

INLETS

1/2" NPT

5-7/8"

INLETS 1/2" NPT

OUTLETS

1/2" NPT

OUTLETS

1/2" NPT

3-3/8"

THREADED INLETS

SHR. 1/2" NOM.

COPPER SWEAT

TUB 1/2" NOM.

COPPER SWEAT

4-1/16"

5-7/8"

INLETS

4-1/16"

INLETS

1/2" NOM.

COPPER

SWEAT

SHR. 1/2" NOM.

COPPER SWEAT

TUB 1/2" NOM.

COPPER SWEAT

SWEAT

INLETS

SWEAT

INLETS (STOPS)

INLETS

1/2" NOM.

COPPER

SWEAT

M968592 Rev.1.3

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

1-3/4"

2-1/4"

Summary of content (3 pages)

PAGE 1
Installation Instructions GREEN TEA T010.5XX PRESSURE BALANCING BATH AND SHOWER TRIM KIT Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 M968592 Rev.1.
PAGE 2
1 INSTALL VALVE TRIM Figure 1. Remove plaster guard from valve. Push CAP (1) over VALVE CARTRIDGE (2) until seated against stop. PLSTER GUARD 1 Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1) and attach with LONG SCREWS (4). Mount ESCUTCHEON SUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORT SCREWS (6). Figure 3. Align PINS (7) on back side of ESCUTCHEON (8) with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5) and press ESCUTCHEON (8) flush against finished wall. 2 Figure 1.
PAGE 3
ADJUST HOT LIMIT STOP HOT LIMIT SAFETY STOP ADJUSTMENT By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP. Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP (1). Follow Step "A" or "B" to adjust min./max. discharge temperature.