Installation Instructions

ManualsBrandsAmerican Standard ManualsShop AllAmerican Standard 3-Way Diverter Rough In Valve with Shared Functions - 3 Individual Functions and 3 Shared Functions

- 1 -

M965673 (2/16)

Thank you for selecting American-Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please

read these instructions carefully before you begin.

Installation must conform to all local building codes.

Certied to comply with ANSI A112.18.1

INSTALLATION

INSTRUCTIONS

R422; R433

TWO/THREE WAY

IN-WALL DIVERTER

ROUGH VALVE

DISCRETE OUTLETS

Product names listed herein are trademarks of AS America, Inc.

R422 R433

Adjustable Wrench Teon TapeChannel Locks

Tubing Cutter

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,

supply stores. It is essential that the tools and materials be on hand before work is begun.

ROUGHING-IN DIMENSIONS:

• NOTE: No concealed piping furnished

FINISHED

WALL

FINISHED

WALL

2-1/4"

(57 mm)

TWO WAY

BODY

ALL CONNECTIONS 1/2" NPT

FINISHED

WALL

FINISHED

WALL

2-1/4"

(57 mm)

THREE WAY

BODY

ALL CONNECTIONS 1/2" NPT

3-1/8"

(80 mm)

2-3/4"

(71 mm)

1-3/4"

(46 mm)

3-1/8"

(80 mm )

1-1/4

(31 mm )

1-5/8

(40 mm )

3-1/8"

(80 mm)

2-3/4"

(71 mm)

1-3/4"

(46 mm)

1-5/8

(40 mm )

1-5/8"

(40 mm )

1-5/8

(40 mm )

1-5/8

(40 mm )

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS R422; R433 TWO/THREE WAY IN-WALL DIVERTER ROUGH VALVE R422 DISCRETE OUTLETS R433 Certified to comply with ANSI A112.18.1 Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Installation must conform to all local building codes.
PAGE 2
1 ROUGHING-IN CAUTION DO NOT SEAL ANY OUTLETS. DIVERTER CANNOT BE USED AS A STOP VALVE. • Turn off hot and cold water supplies before beginning. • See Roughing-in Drawing on reverse side. The port with the BATH TUB picture is the high flow. • The DIVERTER can be installed with the inlet rotated in any position. • Supply connections are 1/2" (13mm) NPT connections. • For proper positioning the finished wall must be within side of PLASTER GUARD. • Connect water to valve.
PAGE 3
INSTALL TRIM • After finished wall is complete, remove, PLASTER GUARD. • See Seperate installation instructions supplied with trim kit for handle assembly. 4 SERVICE TO REPLACE O-RINGS: • Turn off water supply. • Unscrew CAP and remove STEM, SPRING and SEALS. • Remove old DIVERTER elements and install new parts. • Replace remaining parts in reverse order. • NOTE: Repair part numbers are 1 thru 9.
PAGE 4
TWO/THREE WAY IN-WALL DIVERTER ROUGH VALVE, DISCRETE OUTLETS MODEL NUMBER R422; R433 051310-0070A M964432-0070A SPRING KIT DIVERTER REPAIR KIT 912737-0070A STEM O-RING 051309-0070A CAP PLASTER GUARD TWO WAY BODY 060219-0070A STEM KIT 912647-0070A CAP SEAL THREE WAY BODY 963554-YYY0A EXTENSION KIT HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 10:00 a.m. to 4:00 p.m.