INSTALLATION INSTRUCTIONS FUN BATH Models # KT.001, KT.002, KT.003 F U T U R E U S E Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. S A V E F O R Model # KT.001 Model # KT.002 Model # KT.
! SAFETY WARNINGS ! WARNING: DROWNING HAZARD - Infants have DROWNED in bath tubs, ALWAYS keep child with in adult’s reach. WARNING: Never leave child unattended when using tub. WARNING: Never allow other children to substitute for adult supervision. WARNING: Never lift this product with child in it. WARNING: Never place this product in water, in a an adult bath tub or sink. WARNING: Children can drown in as little as 1 inch of water, always bathe your child in as little water as necessary.
Parts List Front Apron Tub Upper Frame Tub Front Support (2x) Reinforcement Bar (2x) Lower Frame Grab Bar (1x) & Polished Washers (2x) Hand Held Shower & Hose Hex Bolt 1" Long (2x) Washer (20x) Carriage Bolt 2" Long (2x) Hex Nut (8x) Shark Bite Fitting 1/2 NPT to Smooth Pipe 3 Flat Head Machine Screw 1-1/2" Long (6x) Quick Release Pin (x) Leveling Feet (4x) 754695-100
1 2 Remove faucet spout from wall. Some faucets have set screws on the bottom of spout. And need an Allen wrench to be removed. After removing faucet check if the water inlet pipe, is threaded or non-threaded. For non-threaded pipe use the SHARK BITE FITTING to attach to HAND HELD HOSE. Threaded Remove faucet spout from wall Some faucets only need to be twisted to be removed. Non-Threaded 3 4 Add LEVELING FEET to FRONT TUB SUPPORTS. Remove Knob Add LEVELING FEET to LOWER FRAME.
Add FRONT TUB SUPPORTS to UPPER FRAME. Use the QUICK PUSH BUTTON to lock FRONT TUB SUPPORT in place, at desired height. Push Button Adjustment 6 Add LOWER FRAME to UPPER FRAME.
7 Add REINFORCEMENT BAR to FRAME.
8 Mount FRAME to existing bath tub. Adjust LEVELING FEET so frame sits on existing bath tub. CAUTION: Be sure existing tub drain is in open position before installing the Fun Bath. WARNING: Only hand tighten LEVELING FEET, overtightening can crack or puncture the preexisting tub. 9 Drain and overflow install.
10 11 Inspect MOUNTING BRACKETS, gather QUICK RELEASE PINS (4x), for next step. Mounting Brackets are Factory Installed to Tub Place tub over frame, align MOUNTING BRACKETS with frame holes. Use QUICK RELEASE PINS to secure tub to frame.
13 Add GRAB BAR to tub, align with pre-drilled holes. Grab Bar Polished Washer Use Hex Nuts and Washers to secure Grab Bar under tub 14 Mount HAND SHOWER on tub deck.
15 Final step, add APRON to front of tub. Always keep FRONT APRON on tub while in use. Front Apron SUGGESTED TUB SIZES FOR USE WITH THE FUN TUB Minimum 58-1/2" Length Minimum 58-1/2" Length Minimum 30" Width Maximum 6" Wide Deck Be sure any wall mount items are above or below the 2"deck Once installed the Fun Bath will be 36" tall, be sure there are no soap dishes, shelving or faucetry that would interfere with installation.
LIMITED WARRANTY COVERAGE AS America, Inc. “American Standard” Fun Baths are warranted in accordance with the following warranty: This warranty is extended to the first purchaser and does not extend to products previously used as display models or products that have been modified or repaired by anyone else but American Standard unless approved by American Standard. American Standard premium acrylic Fun baths come with a fifteen (15) year warranty on the bathtub, ten (10) year warranty on the tub components.